Miele PT 7136 PLUS At the end of a program, Remaining time, Before the end of a program

Page 14

Use

Remaining time

When a program is selected, the approximate duration is displayed. This is the "remaining time".

The program duration can vary due to some factors: residual moisture after spinning, fabric, load size, room temperature and voltage fluctuations.

The adaptive electronic adjusts to the individual load to display the accurate remaining time. The remaining time is constantly checked which can lead to leaps in time.

The "Woolens handcare" and "Smoothing" programs can be ended ahead of time once a certain temperature is reached. This may be the case with fine fabrics or if the dryer had some residual heat from a previous program.

Before the end of a program

After drying with hot air, the cool down phase finishes the program. "Cooling down" is displayed. Only after the cooling phase has ended is the program finished.

The programs: "Woollen handcare" and "Smoothing" do not have a cooling down phase.

7. At the end of a program

"Anti-crease" (if selected) and "End" mark the end of a program in the display. During the anti-crease phase the drum will turn in intervals if the laundry is not immediately removed from the dryer to prevent the laundry from wrinkling. Run time 1 h.

Use the button to open the drum door.

Remove the laundry.

Check the drum for any missed pieces of laundry. Any items left in the dryer can be damaged because of over-drying.

If the door stays open, the light goes off after a few minutes (saving energy).

Close the door.

Cleaning and care hints

See "Cleaning and Care".

14

Image 14

Contents Operating and Installation manual Vented Dryer PT 7136 Plus Contents Contents Important Safety Instructions Important Safety Instructions Save These Instructions Guide to the dryer Control panelJog shuttle Display functionMain menu Program selection possibilityBasic menu of a drying program SettingsMenu Program selection Language Before using for the first timeWelcome screen Set the time of dayDrying tips UseFabric care labels Sort the laundry Load the laundryInsert coins if operated by coin mechanism Select Low temp. and/or TimerSelect a program Starting a programRemaining time Cleaning and care hintsAt the end of a program Before the end of a programAdding/removing laundry during a drying program Canceling a programCoin mechanism Continue dryingProgram guide Cool air Woollen handcareSmoothing Warm airShirts JeansNormal, Hand iron ProofingStarting the timer function TimerSelect the submenu Timer Canceling the timerBasic menu FavoritesSelecting/Changing a Favorite Other programs Drying level programsProgram Warm air, Cool air Assigning a direct select button Low tempSaving a Favorite Removing the lint filter Cleaning and CareCleaning the lint filter Disassembling the lint filterClean the lint filters dry Clean the lint filters wetCleaning the exterior and the control panel Inserting the lint filterWhat if Possible cause Solution Frequently asked questionsCheck and fault messages in the display Appears What if Possible cause Solution At the end of aProgram Other faults Drum? What if Possible fault Solution What if there isCondensed water Items madeBe started, What if Possible cause Solution Program cannotStart indicator Display remainsChanging the light bulb After sales service Optional accessoriesInstallation Instructions Important Safety Instructions Save These Instructions Installation Front viewSide view Rear view Top view Washer/ Dryer Stack Installation on a cement base Coin mechanism Level the dryer InstallationTransporting the dryer to the installation site Electrical connection Installation of exhaust venting General notesHow to calculate the effective duct length Tips about the ductwork Additional duct lengths 4 rigid pipe only Length Determining the position of the exhaust connection Changing the position of the exhaust connectionWindow connection Wall connection with rigid pipeChimney connection Direct wall connection Dryer top viewCollective exhaust duct Technical Data Disposal of an appliance Caring for the environmentDisposal of the packing materials Menu Settings To adjust standard settings Selecting Settings SettingsOpening the menu Settings Leaving the Settings menuOff LanguageAnti-crease Time of day NormalContrast/Brightness Not during current program default settingDelivery status 0 minutes normal cooling down phase StandbySettings Supervisor level Entering the codeSort languages Supervisor levelTimer Language entry Drying levelsDisplay the residual moisture as a percentage Cleaning the airways Cleaning the lint filtersNormal Factory default Light Cool air freePage Page Page All rights reserved Nr 975 240