Miele PT 7136 PLUS What if Possible cause Solution At the end of a, Program, Appears

Page 27

Frequently asked questions

What if ...	Possible cause	Solution
At the end of a	The dryer reminds you to	– Remove and clean the lint filter.
program	clean the lint filter.	To delete this message:
Clean filter or		–	Confirm with "OK".
Clean the lint filter		–	Confirm with "OK".
Clean the lint filter	The cycle of the "Clean	–	See "Settings - Supervisor level
appears	filter" message can be		- Cleaning the lint filters".
	filter" message can be		- Cleaning the lint filters".
	adjusted.
Clean out airways	The dryer does not work	– Check all possibilities as
	at its optimum or not		described under "Other faults -
	efficiently.		The program runs too long or
	Possible cause:		stops".
	clogging by lint or	To delete this message:
	detergent residues.	–	Confirm with "OK".
	The exhaust duct may	With a long exhaust duct, program
	be very long. This is not	times and energy consumption
	a fault.	increase.
		The "Clean out airways" message
		cycle can be adjusted.
		–	See "Settings - Supervisor level
			- Cleaning the airways".
Program finish	This is not a fault.	While the timer was counting
time changed		down, the settings were changed
		down, the settings were changed
		or there was a power failure.

27

Image 27

Contents Operating and Installation manual Vented Dryer PT 7136 Plus Contents Contents Important Safety Instructions Important Safety Instructions Save These Instructions Control panel Guide to the dryerProgram selection possibility Display functionMain menu Jog shuttleSettings Menu Program selectionBasic menu of a drying program Set the time of day Before using for the first timeWelcome screen LanguageUse Fabric care labelsDrying tips Load the laundry Sort the laundryStarting a program Select Low temp. and/or TimerSelect a program Insert coins if operated by coin mechanismBefore the end of a program Cleaning and care hintsAt the end of a program Remaining timeContinue drying Canceling a programCoin mechanism Adding/removing laundry during a drying programProgram guide Warm air Woollen handcareSmoothing Cool airProofing JeansNormal, Hand iron ShirtsCanceling the timer TimerSelect the submenu Timer Starting the timer functionFavorites Selecting/Changing a FavoriteBasic menu Drying level programs Program Warm air, Cool airOther programs Low temp Saving a FavoriteAssigning a direct select button Disassembling the lint filter Cleaning and CareCleaning the lint filter Removing the lint filterClean the lint filters wet Clean the lint filters dryInserting the lint filter Cleaning the exterior and the control panelFrequently asked questions Check and fault messages in the displayWhat if Possible cause Solution What if Possible cause Solution At the end of a ProgramAppears Other faults Items made What if Possible fault Solution What if there isCondensed water Drum?Display remains What if Possible cause Solution Program cannotStart indicator Be started,Changing the light bulb Optional accessories After sales serviceInstallation Instructions Important Safety Instructions Save These Instructions Front view InstallationSide view Rear view Top view Washer/ Dryer Stack Installation on a cement base Coin mechanism Installation Transporting the dryer to the installation siteLevel the dryer Electrical connection General notes Installation of exhaust ventingHow to calculate the effective duct length Tips about the ductwork Additional duct lengths 4 rigid pipe only Length Changing the position of the exhaust connection Determining the position of the exhaust connectionWall connection with rigid pipe Window connectionChimney connection Dryer top view Direct wall connectionCollective exhaust duct Technical Data Caring for the environment Disposal of the packing materialsDisposal of an appliance Menu Settings To adjust standard settings Leaving the Settings menu SettingsOpening the menu Settings Selecting SettingsNormal LanguageAnti-crease Time of day OffStandby Not during current program default settingDelivery status 0 minutes normal cooling down phase Contrast/BrightnessEntering the code Settings Supervisor levelSupervisor level Sort languagesLanguage entry Drying levels TimerCool air free Cleaning the airways Cleaning the lint filtersNormal Factory default Light Display the residual moisture as a percentagePage Page Page All rights reserved Nr 975 240