Miele PT 7136 PLUS installation manual Important Safety Instructions

Page 5

IMPORTANT SAFETY INSTRUCTIONS

￿To prevent the risk of fire, the following articles must not be dried in this tumble dryer:

items which have not been washed.

items, such as workwear, which have not been thoroughly cleaned and are still soiled with grease, oil or other substances (such as cosmetics, lotions, etc.)

If items have not been thoroughly cleaned there is a danger that they could ignite when heated, even after they have been removed from the dryer at the end of the program.

items that have been previously cleaned, washed, soaked or spotted with gasoline, dry-cleaning solvents, wax, wax remover, chemicals for buffing (e.g. mops and floor cloths) or other flammable or explosive substances. They may give off vapors that could ignite or explode.

items which have been spattered with hair spray, nail polish remover or similar substances.

When washing such heavily soiled items ensure that you use sufficient detergent and select a high temperature. If in doubt, wash the items several times.

￿To prevent the risk of fire, the following articles or items must not be dried in this tumble dryer:

fabrics which contain a large amount of rubber, foam rubber or rubber-like materials. For example, products made from latex, shower caps, waterproof textiles, rubberized articles, and items of clothing and pillows with foam rubber filling, or similarly textured rubber-like materials.

which contain padding or fillings (e.g. pillows, jackets). If these were damaged the filling could get out with the risk of igniting in the dryer.

￿In many programs, the heating phase is followed by a cooling down phase to ensure that the items are not too hot to handle when you remove them (this also avoids the danger of the laundry self-igniting). The program is not finished until the cooling down phase is complete.

Always wait until the end of the program before removing the laundry.

￿Warning: Do not switch the tumble dryer off before the end of the drying program. If this was done and the laundry was then removed immediately it could give off a great amount of heat.

￿Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

5

Image 5
Contents Operating and Installation manual Vented Dryer PT 7136 Plus Contents Contents Important Safety Instructions Important Safety Instructions Save These Instructions Control panel Guide to the dryerMain menu Display functionJog shuttle Program selection possibilityBasic menu of a drying program SettingsMenu Program selection Welcome screen Before using for the first timeLanguage Set the time of dayDrying tips UseFabric care labels Load the laundry Sort the laundrySelect a program Select Low temp. and/or TimerInsert coins if operated by coin mechanism Starting a programAt the end of a program Cleaning and care hintsRemaining time Before the end of a programCoin mechanism Canceling a programAdding/removing laundry during a drying program Continue dryingProgram guide Smoothing Woollen handcareCool air Warm airNormal, Hand iron JeansShirts ProofingSelect the submenu Timer TimerStarting the timer function Canceling the timerBasic menu FavoritesSelecting/Changing a Favorite Other programs Drying level programsProgram Warm air, Cool air Assigning a direct select button Low tempSaving a Favorite Cleaning the lint filter Cleaning and CareRemoving the lint filter Disassembling the lint filterClean the lint filters wet Clean the lint filters dryInserting the lint filter Cleaning the exterior and the control panelWhat if Possible cause Solution Frequently asked questionsCheck and fault messages in the display Appears What if Possible cause Solution At the end of aProgram Other faults Condensed water What if Possible fault Solution What if there isDrum? Items madeStart indicator What if Possible cause Solution Program cannotBe started, Display remainsChanging the light bulb Optional accessories After sales serviceInstallation Instructions Important Safety Instructions Save These Instructions Front view InstallationSide view Rear view Top view Washer/ Dryer Stack Installation on a cement base Coin mechanism Level the dryer InstallationTransporting the dryer to the installation site Electrical connection General notes Installation of exhaust ventingHow to calculate the effective duct length Tips about the ductwork Additional duct lengths 4 rigid pipe only Length Changing the position of the exhaust connection Determining the position of the exhaust connectionWall connection with rigid pipe Window connectionChimney connection Dryer top view Direct wall connectionCollective exhaust duct Technical Data Disposal of an appliance Caring for the environmentDisposal of the packing materials Menu Settings To adjust standard settings Opening the menu Settings SettingsSelecting Settings Leaving the Settings menuAnti-crease Time of day LanguageOff NormalDelivery status 0 minutes normal cooling down phase Not during current program default settingContrast/Brightness StandbyEntering the code Settings Supervisor levelSupervisor level Sort languagesLanguage entry Drying levels TimerNormal Factory default Light Cleaning the airways Cleaning the lint filtersDisplay the residual moisture as a percentage Cool air freePage Page Page All rights reserved Nr 975 240