Miele PT 7136 PLUS What if Possible cause Solution Program cannot, Be started, Display remains

Page 30

Frequently asked questions

What if ...	Possible cause	Solution
A program cannot	The fault cannot be	– Is the dryer connected to
be started, the	detected immediately.		the power mains?
display remains		–	Is the door closed?
dark.		–	Are the fuses blown?
		–	Are the fuses blown?
The drum light does	The light turns off	After closing and opening the
not come on.	automatically (energy	door the light comes back on.
	saving).
	The bulb may be bad or	Change the light bulb. See
	burnt out.	"Dryer Care".
The display shows a	A different language was	Select the desired language.
foreign language.	selected under "Settings -	The flag symbol leads you to
	Language ".	the setting.
The "Start" indicator	This is not a fault.	After the program is started,
flashes when	It indicates that the	the indicator lights steadily.
selecting a program.	program can be started.
The display is dark,	The display and the	Press any button to turn the
the ring of light	program selector go into	display and jog shuttle back
around the jog	"Standby" mode to save	on.
shuttle does not	energy.
light.	If pressing a button does	Contact the Miele Technical
	If pressing a button does	Contact the Miele Technical
The "Start" indicator	not bring the display and	Service Department.
flashes slowly.	light back on, a fault has
	occurred.

30

Image 30

Contents Operating and Installation manual Vented Dryer PT 7136 Plus Contents Contents Important Safety Instructions Important Safety Instructions Save These Instructions Guide to the dryer Control panelJog shuttle Display functionMain menu Program selection possibilitySettings Menu Program selectionBasic menu of a drying program Language Before using for the first timeWelcome screen Set the time of dayUse Fabric care labelsDrying tips Sort the laundry Load the laundryInsert coins if operated by coin mechanism Select Low temp. and/or TimerSelect a program Starting a programRemaining time Cleaning and care hintsAt the end of a program Before the end of a programAdding/removing laundry during a drying program Canceling a programCoin mechanism Continue dryingProgram guide Cool air Woollen handcareSmoothing Warm airShirts JeansNormal, Hand iron ProofingStarting the timer function TimerSelect the submenu Timer Canceling the timerFavorites Selecting/Changing a FavoriteBasic menu Drying level programs Program Warm air, Cool airOther programs Low temp Saving a FavoriteAssigning a direct select button Removing the lint filter Cleaning and CareCleaning the lint filter Disassembling the lint filterClean the lint filters dry Clean the lint filters wetCleaning the exterior and the control panel Inserting the lint filterFrequently asked questions Check and fault messages in the displayWhat if Possible cause Solution What if Possible cause Solution At the end of a ProgramAppears Other faults Drum? What if Possible fault Solution What if there isCondensed water Items madeBe started, What if Possible cause Solution Program cannotStart indicator Display remainsChanging the light bulb After sales service Optional accessoriesInstallation Instructions Important Safety Instructions Save These Instructions Installation Front viewSide view Rear view Top view Washer/ Dryer Stack Installation on a cement base Coin mechanism Installation Transporting the dryer to the installation siteLevel the dryer Electrical connection Installation of exhaust venting General notesHow to calculate the effective duct length Tips about the ductwork Additional duct lengths 4 rigid pipe only Length Determining the position of the exhaust connection Changing the position of the exhaust connectionWindow connection Wall connection with rigid pipeChimney connection Direct wall connection Dryer top viewCollective exhaust duct Technical Data Caring for the environment Disposal of the packing materialsDisposal of an appliance Menu Settings To adjust standard settings Selecting Settings SettingsOpening the menu Settings Leaving the Settings menuOff LanguageAnti-crease Time of day NormalContrast/Brightness Not during current program default settingDelivery status 0 minutes normal cooling down phase StandbySettings Supervisor level Entering the codeSort languages Supervisor levelTimer Language entry Drying levelsDisplay the residual moisture as a percentage Cleaning the airways Cleaning the lint filtersNormal Factory default Light Cool air freePage Page Page All rights reserved Nr 975 240