Miele PT 7136 PLUS installation manual Use, Fabric care labels, Drying tips

Page 11

Use

Fabric care labels

Before drying, check fabric care labels for special drying instructions.

￿= Drying with normal temperature

￿= Drying with low temperature

￿= Do not dry in a tumble dryer

Drying tips

Observe the maximum loads, see the "Program guide".

Overloading the dryer will result in poor drying and wrinkling.

Do not place dripping wet items in the dryer. Spin the laundry after the wash for at least 30 seconds.

Dry delicate fabrics (with the fabric care symbol ￿) with the "Low temperature" option.

Open jackets to allow even drying.

Starched laundry can be dried in the tumble dryer. The amount of starch should be doubled during the wash.

Wash new, colored items before drying for the first time and do not dry with light-colored items. These fabrics can "bleed" (also onto plastic parts of the dryer). Colored lint may also get on the light colored items.

Wool and wool blends tend to felt and shrink. Dry wool and wool blends in the "Woollen handcare" program.

The fine fabric of down filled items tend to shrink. Dry these items in the "Smoothing" program.

Dry pure linen items only if it is recommended on the fabric care label. The surface of the fabric may become "rough". Dry these items in the "Smoothing" program.

Knitted fabrics (e.g. T-Shirts and underwear) tend to shrink when washed and dried for the first time. Do not overdry these fabrics.

Permanent press and delicate fabrics tend to crease more the bigger the load size.

For better drying results reduce the load size or select the "Shirts" program.

11

Image 11
Contents Operating and Installation manual Vented Dryer PT 7136 Plus Contents Contents Important Safety Instructions Important Safety Instructions Save These Instructions Control panel Guide to the dryerProgram selection possibility Display functionMain menu Jog shuttleBasic menu of a drying program SettingsMenu Program selection Set the time of day Before using for the first timeWelcome screen LanguageDrying tips UseFabric care labels Load the laundry Sort the laundryStarting a program Select Low temp. and/or TimerSelect a program Insert coins if operated by coin mechanismBefore the end of a program Cleaning and care hintsAt the end of a program Remaining timeContinue drying Canceling a programCoin mechanism Adding/removing laundry during a drying programProgram guide Warm air Woollen handcareSmoothing Cool airProofing JeansNormal, Hand iron ShirtsCanceling the timer TimerSelect the submenu Timer Starting the timer functionBasic menu FavoritesSelecting/Changing a Favorite Other programs Drying level programsProgram Warm air, Cool air Assigning a direct select button Low tempSaving a Favorite Disassembling the lint filter Cleaning and CareCleaning the lint filter Removing the lint filterClean the lint filters wet Clean the lint filters dryInserting the lint filter Cleaning the exterior and the control panelWhat if Possible cause Solution Frequently asked questionsCheck and fault messages in the display Appears What if Possible cause Solution At the end of aProgram Other faults Items made What if Possible fault Solution What if there isCondensed water Drum?Display remains What if Possible cause Solution Program cannotStart indicator Be started,Changing the light bulb Optional accessories After sales serviceInstallation Instructions Important Safety Instructions Save These Instructions Front view InstallationSide view Rear view Top view Washer/ Dryer Stack Installation on a cement base Coin mechanism Level the dryer InstallationTransporting the dryer to the installation site Electrical connection General notes Installation of exhaust ventingHow to calculate the effective duct length Tips about the ductwork Additional duct lengths 4 rigid pipe only Length Changing the position of the exhaust connection Determining the position of the exhaust connectionWall connection with rigid pipe Window connectionChimney connection Dryer top view Direct wall connectionCollective exhaust duct Technical Data Disposal of an appliance Caring for the environmentDisposal of the packing materials Menu Settings To adjust standard settings Leaving the Settings menu SettingsOpening the menu Settings Selecting SettingsNormal LanguageAnti-crease Time of day OffStandby Not during current program default settingDelivery status 0 minutes normal cooling down phase Contrast/BrightnessEntering the code Settings Supervisor levelSupervisor level Sort languagesLanguage entry Drying levels TimerCool air free Cleaning the airways Cleaning the lint filtersNormal Factory default Light Display the residual moisture as a percentagePage Page Page All rights reserved Nr 975 240