Alliance Laundry Systems P232156R9 manual For Technical Service Distributor ABC

Page 32

Basic Installation/Operation

CAUTION

Be careful around the open door, particularly when loading from a level below the door. Impact with door edges can cause personal injury.

SW025

NOTE: When washing items which may disintegrate or fragment, such as mop heads or sponges, use laundry nets to prevent drain blockage.

IMPORTANT: To prevent out-of-balance conditions, premature wear or damage to machine when using laundry nets, use several small nets in a load.

7.When loading is complete, ensure that all fabric is inside the basket. Then close and lock the door. Add dry supplies are placed in the supply dispenser compartment cups prior to the start of each cycle. Liquid supplies can be injected directly into the supply dispenser by an external chemical supply system.

NOTE: Supply dispenser compartment cups must not be removed when an external chemical injection supply system is attached to the washer- extractor.

8.Press and keypads to select desired wash cycle.

For Technical Service

Distributor ABC

1-800-555-5555

As the cycle proceeds, the display will show a summary of the cycle occurring. Refer to Figure 8

To begin the cycle at any step other than the first step,

press the keypad to advance through the cycle to the desired starting point. (The Rapid Advance feature keypad is enabled at the factory and can be disabled.) Refer to Programming Manual for information to disable Rapid Advance.

If the door is not closed and locked, the display will indicate that the door needs to closed and locked. Refer to Figure 13.

PHM706N

Figure 13

Close door to start cycle or press keypad to return to Cycle Menu.

10.The cycle will continue until its completion. Then the display will show the door is ready to be unlocked and opened.

NOTE: The Drain Step that occurs before an Extract Step or a Spray Rinse Extract Step cannot be skipped using Rapid Advance. The machine MUST drain and balance during the Drain Step before it can extract.

Cycle41:

Supply Set

Up

Cycle Menu

Cycle01:

Towels

White

Bleach

Cycle02:

Towels White

PHM702N

Figure 12

9. Press to start the selected cycle.

30

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232156

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Washer-Extractors Page Contents Explanation of Safety Messages Important Safety InstructionsBasic Installation/Operation Safety Decals Operator Safety General Specifications Specifications 100 125 150 Overall DimensionsWeight And Shipping Information UW UniLinc and M30 Control ModelsDoor Opening Information Drive Train InformationCylinder Speeds / Centrifugal Force Data Balance DetectionElectrical Heating Optional Water Consumption Power ConsumptionUW A-Control, Variable-Speed Models MED Uwpv Models Specifications 100 125 150 Overall Dimensions UW P-Control, Variable-Speed ModelsWash/reverse, RPM / g Distribution, RPM / g UW 2 Speed Models UW35 UW60 Overall Dimensions Domestic shipping volume, ft.3 m3Cylinder Speeds/Centrifugal Force Data UW 3 Speed Models UW35 UW60 Overall Dimensions UW 3 Speed Models with P-Control or597 561 100 125 150 Crush hazardUniLinc and M30 Control Models 911 14 UW150TV Uwav Models Models UW 35 Uwpv Pocket Hardmount Machine Dimensions Refer to and Figure Uwpv ModelsUW35PV UW125PV UW150PV 55.5 1410 64.5 1638 30.5 775 914 203 15.5 394 43.88 UW 2 Speed Models UW 3 Speed Models with P-Control or S-Control UW 3 Speed Models Operation UW Models With UniLinc ControlFor Technical Service Distributor ABC UW Models With M30 Control Cycle Number Cycle Name PHM784N UW Models with S-Control Cycle is complete when display reads donE Operating Instructions UW Models with P-ControlPre-Operating Instructions UW150 Models SW025 UW Models with A-Control Basic Installation/Operation UW Models with B-Control Basic Installation/Operation Disposal of Unit
Top Page Image Contents