Alliance Laundry Systems P232156R9 manual Cycle Number Cycle Name

Page 34

Basic Installation/Operation

CAUTION

Be careful around the open door, particularly when loading from a level below the door. Impact with door edges can cause personal injury.

SW025

NOTE: When washing items which may disintegrate or fragment, such as mop heads or sponges, use laundry nets to prevent drain blockage.

IMPORTANT: To prevent out-of-balance conditions, premature wear or damage to machine when using laundry nets, use several small nets in a load.

6.When loading is complete, ensure that all fabric is inside the basket. Then close and lock the door.

7.Where applicable, add dry supplies into the supply dispenser compartment cups prior to the start of each cycle.

Liquid supplies can be injected directly into the washer-extractor by an external chemical supply system.

NOTE: Supply dispenser compartment cups must not be removed when an external chemical injection supply system is attached to the washer- extractor.

8.Press the numeric keypads to select the desired wash cycle. Refer to Table 11.

Cycle Number

Cycle Name

1

Permanent Press Light Soil

2

Light Soil

 

 

3

Permanent Press Medium Soil

4

Medium Soil

5

Permanent Press Heavy Soil

 

 

6

Heavy Soil

7

Rags

8

Reclaim

 

 

9

Delicates

10

95°C

11

60°C

 

 

12

40°C

13

95°C Permanent Press

14

60°C Permanent Press

 

 

15

40°C Permanent Press

16

70°C Permanent Press

17

50°C Gentle

 

 

18

30°C Gentle

19

Custom #1

20

Custom #2

 

 

21

Custom #3

22

Custom #4

23

Custom #5

 

 

24

Custom #6

25

Custom #7

26

Custom #8

 

 

27

Custom #9

28

Custom #10

29

Custom #11

 

 

30

Custom #12

Table 11

32

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232156

Image 34
Contents Washer-Extractors Page Contents Explanation of Safety Messages Important Safety InstructionsBasic Installation/Operation Safety Decals Operator Safety Weight And Shipping Information General SpecificationsSpecifications 100 125 150 Overall Dimensions UW UniLinc and M30 Control ModelsCylinder Speeds / Centrifugal Force Data Door Opening InformationDrive Train Information Balance DetectionElectrical Heating Optional UW A-Control, Variable-Speed Models Power ConsumptionWater Consumption MED Uwpv Models Specifications 100 125 150 Overall Dimensions UW P-Control, Variable-Speed ModelsWash/reverse, RPM / g Distribution, RPM / g UW 2 Speed Models UW35 UW60 Overall Dimensions Domestic shipping volume, ft.3 m3Cylinder Speeds/Centrifugal Force Data UW 3 Speed Models UW35 UW60 Overall Dimensions UW 3 Speed Models with P-Control or597 561 UniLinc and M30 Control Models Crush hazard100 125 150 911 14 UW150TV Uwav Models Models UW 35 Uwpv Pocket Hardmount Machine Dimensions Refer to and Figure Uwpv ModelsUW35PV UW125PV UW150PV 55.5 1410 64.5 1638 30.5 775 914 203 15.5 394 43.88 UW 2 Speed Models UW 3 Speed Models with P-Control or S-Control UW 3 Speed Models Operation UW Models With UniLinc ControlFor Technical Service Distributor ABC UW Models With M30 Control Cycle Number Cycle Name PHM784N UW Models with S-Control Cycle is complete when display reads donE Pre-Operating Instructions UW Models with P-ControlOperating Instructions UW150 Models SW025 UW Models with A-Control Basic Installation/Operation UW Models with B-Control Basic Installation/Operation Disposal of Unit