Suunto 110.9772 manual Stopping Your Dryer, Pausing or Restarting, Control Locked

Page 16

To make changes during an Auto Cycle:

Press STOP once.

Adjust Dryness Level.

NOTE: Dryness Level selections can be made only while using Auto Cycles. You can select a different dryness level, depending on your load, by pressing Dryness Level and choosing More Dry, Normal or Less Dry. Selecting More Dry, Normal or Less Dry automatically adjusts the sensed time needed.

How Auto Dry works

SmartHeat™ improves drying performance with Auto Moisture Sensing Plus, which advances the cycle as moisture is extracted from clothing. A thermistor (electronic temperature sensor) and moisture sensing strips in the dryer drum help measure the amount of moisture in the clothes as they tumble. An electronic control determines the load type to help save time, avoid overdrying, and increase the accuracy of the end dryness level. After the first 5 minutes of an automatic cycle, the estimated time display will adjust based on the approximate load size, cycle, dryness level selected and amount of moisture left in the clothes. When the clothes have reached approximately 80% of the dryness level selected, the estimated time display will adjust again, showing the final drying time. Auto Moisture Sensing Plus takes the guesswork out of drying time and enhances fabric care.

To use a Timed Cycle

NOTE: A light next to each feature will glow green when the feature is selected or will glow amber when the feature is selectable.

Press a Timed Cycles button.

Press MORE TIME or LESS TIME until the desired drying time is displayed. Tap MORE TIME or LESS TIME, and the time will change by 1-minute intervals. Press and hold MORE TIME or LESS TIME, and the time will change by 5-minute intervals.

NOTE: The More Time and Less Time buttons can be used only with Timed Cycles and the Touch Up Cycle.

Press the POWER button. Then rotate the dial to select the SteamCare Cycle. The indicator light for the selected cycle will glow blue. The preset modifiers for the selected cycle will glow green. Selectable options will glow amber. If an option or modifier is unavailable with the selected cycle, the light will not illuminate. The actual cycle time (in minutes) will show in the display.

Press MORE TIME or LESS TIME until the desired drying time is displayed. Tap MORE TIME or LESS TIME, and the time will change by 1-minute intervals. Press and hold MORE TIME or LESS TIME, and the time will change by 5-minute intervals.

NOTE: The More Time and Less Time buttons can be used only with Timed Cycles and the Touch Up Cycle.

Press TEMPERATURE until the desired temperature glows.

NOTE: During the Touch Up Cycle, you can change the settings for Time, Temperature, WRINKLE GUARD® and End of Cycle Signal. During the Refresh Cycle you can change WRINKLE GUARD® and the End of Cycle Signal. Press STOP twice to stop the dryer and clear the settings. Select another cycle or option.

4.(OPTIONAL STEP) If desired, select OPTIONS. For more details, see “Options.”

5.(OPTIONAL STEP) If desired, set the End of Cycle Signal. Select LOUD or SOFT by pressing the Cycle Signal button to alert you when a cycle ends.

6.Press and hold START for approximately 3 seconds until dryer starts. Be sure the door is closed.

If you do not press START within 5 minutes of selecting the cycle, the dryer automatically shuts off.

If you wish to end your drying cycle after pressing Start, press STOP twice.

Stopping Your Dryer

To stop your dryer at any time

Press STOP twice or open the door.

Press TEMPERATURE until the desired temperature glows.

NOTE: During a Timed Cycle, you can change the settings for Time, Temperature, WRINKLE GUARD® and End of Cycle Signal. Press STOP twice to stop the dryer and clear the settings. Select another cycle or option.

To use a SteamCare Cycle

NOTE: A light next to each feature will glow blue when the feature is selected or will glow amber when the feature is selectable.

Use of a fabric softener sheet is not recommended with SteamCare cycles as it may cause temporary staining on clothes.

Pausing or Restarting

To pause the dryer at any time

Open the door or press STOP once.

To restart the dryer

Close the door. Press and hold START until dryer starts.

NOTE: Drying will continue from where the cycle was interrupted if you close the door and press Start within 5 minutes. If the cycle is interrupted for more than 5 minutes, the dryer will shut off.

Select new cycle settings before restarting the dryer.

Control Locked

This feature allows you to lock your settings to avoid unintended use of the dryer. You can also use the Control Locked feature to avoid unintended cycle or option changes during dryer operation.

To enable the Control Locked feature:

Press and hold CYCLE SIGNAL for 3 seconds. The Control Locked indicator light glows, and a single beep tone is heard. To unlock, press and hold CYCLE SIGNAL for 3 seconds. The indicator light turns off.

16

Image 16
Contents Gas Dryer Table of Contents Kenmore Elite Appliance WarrantyDryer Safety Your safety and the safety of others are very importantTools and Parts Installation InstructionsParts supplied Installation clearances Optional PedestalLocation Requirements Parts neededDryer Dimensions Installation spacing for cabinet installationCloset installation Dryer only Recessed or closet installation Dryer on pedestalMobile home additional installation requirements Dimensions shown are for the recommended spacingMobile home installations require Electrical RequirementsGas Supply Requirements Venting Requirements If using an existing vent systemIf this is a new vent system Vent material Optional exhaust installations Alternate installations for close clearancesSpecial provisions for mobile home installations Plan Vent SystemInstall Vent System Install Leveling LegsVent system chart Connect VentLevel Dryer Connect Inlet HoseMake Gas Connection Reverse Door Swing Remove the doorReverse the hinge Indicated screwsReinstalling the door Complete InstallationReverse the door handle Dryer USE Starting Your DryerIf the dryer will not start, check the following To use an Auto CycleStopping Your Dryer Pausing or RestartingControl Locked Status Lights Drying and Cycle TipsCycles Auto Dry Preset Cycle Settings SteamCare Preset Cycle SettingsJeans Heavy DutyOptions ModifiersEnd of Cycle Signal Tumble Free Heated Dryer RackCleaning the Dryer Location Cleaning the Lint ScreenEvery load cleaning As needed cleaningCleaning the Dryer Interior Removing Accumulated LintWater Inlet Hoses Vacation, Storage and Moving CareTroubleshooting Dryer OperationCycle time too short Lint on loadStains on load or drum Loads are wrinkledProtection Agreements Sears Installation ServiceMaster Protection Agreements Page Índice USO DE LA SecadoraGarantía DE LOS Electrodomésticos Kenmore Elite Garantía Limitada DE UN AÑOSeguridad DE LA Secadora Su seguridad y la seguridad de los demás es muy importanteInstrucciones DE Instalación Herramientas y piezasPiezas suministradas Pinzas Cinta para medirPedestal opcional Requisitos de ubicaciónPiezas necesarias Usted necesitaráDimensiones de la secadora Espacios para la instalaciónEspacio para la instalación en el clóset Instalación en el clóset Sólo secadoraRequisitos eléctricos Las instalaciones en casas rodantes necesitanRequisitos del suministro de gas Requisitos de ventilación El tubo de gas de la secadoraSi usa un sistema de ventilación existente Si éste es un nuevo sistema de ventilaciónInstalaciones alternas para espacios limitados Instalaciones opcionales de escapeVentilación Instalación del sistema de ventilación Instalación de las patas niveladorasDeterminación de la vía del ducto de escape Cuadro del sistema de ventilaciónConexión de las mangueras de entrada Conexión del ducto de escapePara su uso en casas rodantes Nivelación de la secadora Conexión del suministro de gasInversión del cierre de la puerta Desmontaje de la puertaInversión de la bisagra Quite la puertaInversión de la manija de la puerta Reinstalación de la puertaSolución de problemas De problemasComplete la instalación Si la secadora no funciona, revise lo siguientePara hacer cambios durante un ciclo automático USO DE LA SecadoraPuesta en marcha de la secadora Para usar un ciclo automático Auto CycleCómo funciona el secado automático Auto Dry Para usar un ciclo de Cuidado con vapor SteamCarePara usar un ciclo programado Timed Cycle Pausa o reanudación de la marcha Control bloqueado Control LockedSugerencias de ciclos y secado Luces de estadoCiclos Revitalizado Refresh con Cuidado de vapor SteamCare Retoque Touch Up con Cuidado de vapor SteamCareAjustes prefijados del ciclo de Cuidado con vapor SteamCare Ciclos programados Timed CyclesSeñal de secado húmedo Damp Dry Signal OpcionesSonidos de los botones Button Sounds Luz del tambor Drum LightModificadores Cambio de ciclos, opciones y ModificadoresSeñal de fin de ciclo Señal de fin de ciclo End of Cycle SignalEstante térmico de la secadora Cuidado DE LA Secadora Limpieza del lugar donde está La secadoraLimpieza del filtro de pelusa Limpieza del interior de la secadoraMangueras de entrada de agua Cambio de la luz del tamborFuncionamiento de la secadora Solución DE ProblemasResultados de la secadora El tiempo del ciclo es demasiado corto Pelusa en la ropaManchas en la carga o en el tambor Ropa arrugadaContratos maestros de protección Contratos DE ProtecciónServicio de Instalación de Sears W10136974B