Humminbird ICE 55, ICE 35 manual WHAT’S on the Active Display ICE 45/55 only, KEY Functions

Page 24

WHAT’S ON THE ACTIVE DISPLAY (ICE 45/55 ONLY)

Your ICE Flasher Series™ control head sends a sound wave signal and determines distance by measuring the time betweenthe transmission of the sound waveand when the sound wave is reflected off of an object.

As your Ice Fishing transducerreceivessonar signals,it converts them to a digital depth that is shown on the ICE Flasher Series™ Active Display. The depth reading is continuously updated. At initial power-up, the unit will begin normal operation and display the digital depth and the units of measure. The liquid crystal display (LCD), or Active Display,offers sharp viewing, even in bright, direct sunlight, and is continuously lit for nighttime operation. The figure below shows the many features that are available on the Active Display and where each feature will be displayed when you activate it.

NOTE: Actual depth capabilitydepends on such factorsas bottom hardness,waterconditions, and transducer installation. Units will typically read to deeper depths in fresh water than in salt water.

	Voltage
Depth	Target
	Backlight
2 Beams	Feet/Meter
Gain	Zoom
	Zoom

Noise Reject

Color

NOTE: The Active Display is available on ICE 45/55 Flashers only, and certain features are only availableon theICE 55. Read thismanualcompletelyto understandthefullcapabilitiesof yourmodel.

KEY FUNCTIONS

YourICE Flasher Series™ Fishfinderuses a number of keys to control the Range, Zoom, Gain, Noise, Beam, and Color Palettefunctions. While in normal operating mode, press a function key,such as Gain, turn the Selection dial to choose a settingfor that function, then press the Selection Dial to complete your selection.

20

Image 24

Contents ICE 35, ICE 45, ICE Installation and Operations Manual Thank YOU Table of Contents Maintenance TroubleshootingYear Limited Warranty Humminbird Service Policy Specifications Contact HumminbirdHOW Sonar Works Real Time SonarPage Page HOW ICE Flashers Work Installation Overview ICE Flasher Series Base Assembly Assembling the Transducer Storage PostsSlide one spring over each flat-headscrew and set aside Repeat steps 2-5 for the second cable retentionarmInstalling the Handle Onto the Base Sliding in the Handle Assembling the Base and HandleAssembling the Control Head to the Base and Handle Repeat for the other sideICE Flasher Series Assembly Connecting the Power CableCharging and Installing the Battery Slide the Battery Terminal Adapter over each spade terminal Spade Battery TerminalsAssembling the Portable Bag ICE 55 Only Transducer Installation Testing the Transducer Prior to InstallationThis procedure you willassemblethe transducerand float Assembling the Transducer and FloatIce Layer Float Transducer Connecting the Transducer Cable Storing the Transducer Test and Finish the Installation Getting Started Using Your ICE Flasher Series Fishfinder Powering UP the Control Head SimulatorWHAT’S on the Flasher Dial Page WHAT’S on the Active Display ICE 45/55 only KEY FunctionsPOWER/RANGE Dial Selection Dial Range scales for the ICE 35 are shown belowZoom Gain Noise Rejection ICE= 455 kHz, and Wide = 240 kHz Default = Wide ICE 45/55 BeamPress the Beam key to toggle between 240 kHz and 455 kHz Palette1 ICE 35/45/55 See Palette 1, Palette 2, or Palette 3 for more informationPalette2 ICE 55 Only Palette3 ICE 55 Only OrangeTarget ICE 55 Only Dual Mode KEY Functions Maintenance ICE Flasher Series MaintenanceTransducer Maintenance Troubleshooting ICE Flasher Series Fishfinder Doesn’t Power UpYear Limited Warranty Humminbird Service Policy Returning Your Unit for Service Specifications Which your product was purchased Page Contact Humminbird By e-mail