Bosch Appliances D9112 Command 5 7 Toggles Default Idle Text, Command 5 9 Shows Firmware Revision

Page 85

Command 5 7 Toggles Default Idle Text

Command 5 7 allows technicians who might not be familiar with the custom idle text to confirm whether an area is armed or ready to arm. The default idle text displays are:

AREA # IS ON AREA # IS OFF

Follow the procedure below to toggle between custom and default idle text.

1.Ensure the command center is at idle text.

2.Press COMMAND 5 7.

3.The display will change to default idle text for 5 seconds and then revert to its original idle text.

Command 5 9 Shows Firmware Revision

Command 5 9 displays the revision of firmware currently installed in the panel.

1.Ensure the command center is at idle text.

2.Press COMMAND 5 9.

3.The current revision of firmware displays (9112 REV # # - # # ) for 5 seconds.

4.The display returns to idle text.

	D9112	Operation & Installation Manual

74-06144-000-C 2/96		Page 85	© 1993-1996 Radionics

Image 85

Contents D I O N I C S Part FCC Notices74-06144-000-C 2/96 Table of Contents Installation Guide for UL and Fire Applications Programmer and Accessory ConnectionsCurrent Rating Chart for Standby Battery Calculation forFigures and Tables D8128A OctoPOPIT Switch SettingsPoints IntroductionKeyswitch D1255 Alpha III Command CenterAreas and Accounts CommunicatorEvent Log Event MemoryEMI/Lightning Transient Protection ProgrammingOther Features D9112 Assembly D9112 Control/Communicator AssemblyOrdered Separately Literature PackFire Listings and ApprovalsBurglary Factory Mutual FMBeginning the Installation InstallationBefore You Begin Enclosure OptionsPremises Wiring Connecting Earth Ground TerminalInstalling the D9112 Assembly Lock the Reset Pin Now Locking the Reset PinCharge the Battery as You Finish Finishing the InstallationInstall and Wire Detection Devices Install Modules and RelaysConnect the On-Board Points and Command Centers Install the Point Chart LabelPower Up Programming the PanelTesting the System Primary Power Terminals Power SupplyPrimary AC Power Circuit Installing the TransformerSecondary DC Power Secondary Power TerminalsInstalling the Battery Battery SupervisionBattery Discharge/Recharge Schedule No AC Power Battery Charging CircuitFloat Charge Discharge CycleLow Battery LED Red Charging Status and Low Battery LEDsCharging Status LED Yellow Available Power Power OutputsCircuit Protection Accessory Connector J2 Continuous Power Outputs TerminalsContinuous Current Draw Expansion Port J4Relay Installation Programmable Power Outputs TerminalsProgramming Optional Relays RequiredVerification/Reset Relay Available PowerTerminals 6 TerminalRegistration Telephone ConnectionsNotification LocationPhone LED Red Phone Cord ConnectionOperation Monitor LED Green Dialing FormatGround Start Relay InstallationGround Start Jumper D128 Dual Phone Line SwitcherDescription OperationInstalling the D128 Watchdog FeaturePrimary Phone Lines, Primary Phone Numbers D128 Status LEDs AC Power LEDPrimary Fail LED Secondary Fail LEDDescription Terminals 11 to On-Board PointsPoint Sensor Loops Point Response Time Point ParametersPoint Zonex Buss Terminals 23 to Off-Board PointsD8125 Popex Module D8127 Popit Modules Wiring the D8125 to the D9112 Installing the D8125 Popex ModuleListings MountingD8125 D9112Zonex +UP to 63 Point PointsData Expansion Loop Wire Specifications Wiring POPITs to the Data Expansion LoopPopit Sensor Loops Wiring Data Expansion Loops to Popex ModulesD9112 Program Record Sheet Point AssignmentsPopit Labels Vertical Grid for Popex #1D8128A OctoPOPIT Module Installing the OctoPOPITListing D8128A OctoPOPITs Wiring OctoPOPITs to the D9112Line Termination Point Assignment Switches Sensor Loop SwitchesOctoPOPIT Sensor Loops Sensor Loop D9112 Point #Testing Off-board Points Off-board Relays Configuring the D8129 OctoRelayD8129 OctoRelay Relay OutputsD8129 Switch Settings Wiring Connections InstallationRelay Output D811 Arm Status Relay ModuleD811 Module Wiring D1255 Address Settings D1255 Command Centers Terminals 29 toArming Devices DescriptionD1255 Connections D9112 Command Center Terminal Function Wire ColorD9112 Power at Command CentersMaintained Contact Keyswitch OperationMomentary Contact Silencing the BellProgrammer Connector J7 Programmer and Accessory ConnectionsProgrammer Access Reports Accessory Connector J2Expansion Port J4 D9112 Terminal Name Description Quick Reference Terminal DescriptionInstallation Guide for UL and Fire Applications Optional Compatible Equipment IntroductionBurglary Applications Fire ApplicationsFire Applications Enclosures D129 Class a System ChartSystem Wiring Diagram, Issue a Total a = Total B = Total C 1 = Current Rating Chart for Standby Battery CalculationsCurrents shown in milliamperes 1 ampere=1000 milliamperes Central Station or Local Fire Alarm Standby Battery RequirementsRemote Station or Auxiliary Fire Alarm Household Burglary and Commercial BurglaryCentral Station or Local Systems Current Chart FirstHousehold Fire Ampere-Hour Calculation Formula Remote Station or Auxiliary SystemsSelf Diagnostics Troubleshooting GuideCall for Service Trouble at Command Center Panel Broken Hardware, Software FailedServc Batt LOW Battery Voltage Low Servc AC Fail AC Power FailedServc Batt Msing Battery Missing, Shorted, or Reversed Servc Keypad Supervised Command Center MissingPhone Line Trouble Symptom Diagnosis RemedyCommunications Failure Zonex BUS Problems Programming the PanelSee Problems with Data Expansion Loop Problems with PointsSymptom Diagnosis Remedy Symptom Diagnosis Remedy Metering the Loops Problems with the D8125 Popex Data Expansion LoopsChecking Shielded Cable EMI on Long Wire RunsNCI #1, #40 Problems with Command CentersWatchdog Reset Reports Battery and Power ReportsRunaway Reports to the Receiver Overloaded Power Supply Service Walk Test Service Walk ? Command 5 9 Shows Firmware Revision Command 5 7 Toggles Default Idle TextPress Command 5 Specifications SDI Bus Compatible AccessoriesTelephone Connections Environmental