Toro SA41 owner manual Introduction, Warranty Card, Installation

Page 2

INTRODUCTION

Thank you for purchasing the Selectronic Sine wave inverter, model SA41 with ENERGY MANAGEMENT.

Your SA41 is a state-of-the-art high performance TRUE SINE WAVE DC to AC Power Inverter incorporating ENERGY MANAGEMENT, a unique energy monitoring and controlling system developed by Selectronic to enable you to maximise your limited energy resource.

Thousands of hours of development time have been invested in the SA41 to provide you with a reliable, high quality product. The output from your SA41 is as good as, if not better than mains power and if looked after properly, the SA41 will give you many years of reliable service.

WARRANTY CARD

Before proceeding any further, it is extremely important that you complete your warranty card NOW. This will enable us to immediately register your initial 24 month warranty period, and also make you eligible for our free lifetime warranty extension. Six months after the purchase date of the SA41, Selectronic will send you a questionnaire. Simply complete and return the questionnaire to us and we will extend your warranty, free of charge, for a lifetime. By accurately completing your warranty card and questionnaire, you will provide us with valuable information that will assist us in keeping up with your alternative energy needs. Please take a few moments to fill in the warranty card. Your efforts will be greatly appreciated.

INSTALLATION

300mm

The installation of your inverter is

 

SELECTRONIC SINE WAVE INVERTER

extremely

important.

Failure

to

 

 

 

follow

the

recommended

 

 

 

installation

instructions

may

void

 

WITH ENERGY MANAGEMENT

SA41

your

warranty.

If in

doubt,

ask

 

DC TO MAINS POWER

PROUDLY DESIGNED & MADE IN AUSTRALIA

your supplier.

 

 

 

 

 

 

 

After unpacking the SA41, check

 

200mm

 

for any damage which may have

 

 

occurred during transit. If there are

 

 

 

any signs of damage, contact your

 

 

 

supplier immediately.

 

 

 

 

 

 

The inverter must be installed in a

300mm

 

300mm

 

 

 

dry, cool, dust-free environment.

 

 

 

Please leave at least 300mm

 

 

 

clearance at the left and right hand

 

 

 

sides

(Black

heatsink

fins),

 

 

 

300mm above the inverter and

 

Front

 

approx. 200mm at the rear as this

 

 

will aid the natural cooling of the inverter. The air vents on the underside of the SA41 also need to be kept clear of obstructions.

2

Image 2
Contents Selectronic Australia Introduction Warranty CardInstallation Connection of AC and DC Wiring SupplyRED = Battery Positive + Black = Battery Negative Energy Management Status Standby Inverter OFF Inverter on Status ResetOperation StatusWhere the Optional 200 AMP Current Shunt is Installed Minimum Charge On with OFF Set Control On with on On with Time Set Control SettingsController Outputs Lockout DurationBuzzer Lockout More SettingsBuzzer on / OFF SET DAYLockout Alarm Input AC Volts SettingAlarm Inputs Current Shunt Settings External ShuntMinimum Charge in Battery Battery CapacityCharge in Battery LOW Charge AlarmOverload Shutdown and Alarms Alarm 2 Active Fault FindingAlarm 1 Active Heatsink TOO HOTInverter Shuts Down with LOW Volts Battery Maintenance System MaintenanceSA41 Maintenance SA41 Electrical Specifications Demand Start SectionRadio Frequency Interference Handy HintHeatsink Temperature Appendix I DiagnosticsTransformer Temperature Demand Start CurrentAppendix II Flow Diagram for Displays and Settings Minimum Charge Display Switching Between READINGS, Minimum CHARGE, and DiagnosticsDiagnostic Displays Minimum charge DisplaysINV CO, LO A/H or CO+LAHFrom previous SA-SB-01 Interface KIT Appendix III SA Inverter OptionsGeneral Alarm Inputs Examples SA-SB-01 Interface ConnectionsInstallation of SA-KP-01 Optional Keypad Ext. Keypad no Set ParametersExt. Shunt no Set Parameters Installation of SA-S200 Optional Current ShuntAmps 0.0A OUT Battery Zero DC Amps OFF Set ParametersProduct Warranty Conditions Mounting Template for SA-KP-01 Keypad