PowerTec DFS-1 manual Default Setup

Page 18

DEFAULT SETUP

The concept behind the DFS-1 calls for fully programmable inputs and outputs. The ability to change analog and digital inputs and outputs at will lends a whole new meaning to the word "flexibility".

POWERTEC has established a set of "default" parameters which will leave the setup of the DFS-1 in a way that will operate a motor in the basic configuration (see figure 3 on page 3 and figure 4 on page 4). There are two good reasons for doing this:

1.This default setup allows the user to connect and operate a motor using common, everyday connections without having to program the DFS-1 prior to its initial use.

2.The default setup provides a baseline to which the user can return if it appears that something is wrong with either the user's setup or the motor control. There is a command which allows the "reset" of the setup to the default configuration.

Revised 7/95

DFS-1 Manual

Page 13

POWERTEC Ind. Corp.©

 

 

Image 18
Contents DFS-1 Microprocessor Based Brushless D.C Motor ControllerSubsidiary Powertec Industrial Corporation Errata Additional Info OctoberInstallation Mounting -- Read this Entire Section Before StartingContents DFS 1 Setup Communication Protocol Retrofitting the Model 1000,1000A, or 1000ARMenu and Keypad Hierarchy Revised 7/95 Introduction Summary of Warranty and Disclaimer Power Connections ConnectionsMotor Encoder Cable Analog InputsFrequencyinput Analog OutputsFrequencyoutputdigital Inputs Digital Outputs CommunicationsDigital Out #4 Reverse This page WAS Intentionally Left Blank Default Setup Revised 7/95 This Supply is for the Motor Encoder only Power SuppliesInput Setup Function VDCInput #1 Reference Frequency Input Frequency Inputs OutputsDigital Inputs Outputs #1 Reference Frequency OutputCable Standard RS-48519.2K, and 38.4K baud Nodes MaximumThis page WAS Intentionally Left Blank Baud Rate Local / Remote ControlUnit ID Number Baud RateCommunications Protocol Modes of OperationTo 1 decimal Maximum Motor Speed Encoder Pulses PER RevolutionUSE Parameter #6 to SET the Absolute Maximum Motor Speed Slave Ramp UP Time Master Ramp UP TimeMaster Ramp Down Time Slave Ramp Down TimeTo 99,999 decimal Default Value 0000 06D6h Master Preset SpeedSlave Ratio Preset Engineering UnitsAnalog Input #1 Mode Select To 32 decimal Default Value 0000 0001hMaximum Ratio Center value Analog Input #1 Signal ConditioningAnalog Input #1 LOW Engineering Units EGU Future useAnalog Input #1 High Engineering Units EGU Analog Input #2 Mode SelectAnalog Input #2 Signal Conditioning Analog Input #2 LOW Engineering Units EGUAnalog Output #1 LOW Engineering Units EGU Analog Output #1 Mode SelectAnalog Output #2 Mode Select Analog Output #1 High Engineering Units EGUDefault Value 0000 0096h Analog Output #2 LOW Engineering Units EGUAnalog Output #2 High Engineering Units EGU Digital Input #3 Function Digital Input #1 FunctionDigital Input #2 Function Digital Input #4 FunctionDigital Input #7 Function Digital Input #5 FunctionDigital Input #6 Function Digital Output #1 FunctionDigital Output #2 Function Drive Gain SettingDrive Stability Setting Digital Output #3 FunctionModulation and Operation Modes Drive Regenerative Current LimitPulse Multiplier Jump or MOP OperationSlave Jump UP Amount Master Jump UP AmountMaster Jump Down Amount Slave Jump Down AmountMinimum Ratio Communications Turnaround DelayInput Debounce Value Float or FreezeContactordelay Slave JOG Ratio Slave Preset #2Master Preset #2 EGU TAG SelectThis page WAS Intentionally Left Blank DFS 1 Setup Basic Setup of the DFS-1 Controller Master Mode Setup Slave Mode Setup Inputs and Outputs Setup SET Parameter #56 for Communications Turn around Delay Communications SetupThis parameter selects the Powertec binary protocol SET Parameter #3 to Select Which Functions are RemoteError Codes for ON-BOARD Display This page WAS Intentionally Left Blank Communications Protocol Command List Parameter List Dlestxuidnakerrdleetxcsm DlestxuidcmddleetxcsmDLESTXUIDCMDCS4CS3 CS2CS1DLEETXCSM ERRDlestxuidackdleetxcsm Response If no errors and unit i.d. does not equalResponse If no errors DlestxuidcmdprmdleetxcsmDlestxuidcmddtadleetxcsm DLESTXUIDCMDPRMVL4Dlestxuidcmdatddleetxcsm DLESTXUIDACKDA4DA3DLESTXUIDCMDDTAVL4 DlestxuidcmddigdleetxcsmBIT PSN SML Where Is unused Is Jog Is Preset Is Contactor AuxDLESTXUIDCMDDIGVL4 BIT PSN SMHBIT PSN RML Message DLESTXUIDCMD0000Smhsmldleetxcsm BIT PSN RMHAttachmentb Parameter Description DLESTXUIDCMDAMDVL4Additional Info Output Contactor Typical Dynamic Braking Typical This page WAS Intentionally Left Blank Quantity Pin Connector Cable DFS-1 Model 1000 series retro-fit kit consists QuantityRevised 7/95 Appendix B Not visible in some modes Revised 7/95 Powertec Ind. Corp Figures 2 DFS-1 Manual Figures DFS-1 Manual Igur DFS-1 Manual Select AI ModeEnterEnter DFS-1 Manual Igur DFS-1 Manual Sel DFS-1 Manual Igures DFS-1 Manual Figures 29 DFS-1 Manual