Roland VC-2 owner manual Midi/Usb, Chord Memory

Settings Common to All Modes (System Mode)

EQ			Parameter	Value	Explanation
Parameter	Value	Explanation	Tx Edit	OFF, ON	Specify whether changes you
					make in the settings of a patch will
2 Band EQ	OFF, ON	Switch the 2-Band equalizer
					be transmitted as system exclusive
		on/off.			messages (ON), or will not be
LOW Freq	50, 63, 80, 100,	Selects the frequency of the low			transmitted (OFF).
	125, 160, 200,	range.	Clock Out	OFF, ON	Specifies whether MIDI clock will
	250, 315, 400,				be transmitted (ON) or not (OFF).
	500, 630, 800,		USB-MIDI	OFF, ON	This switch specifies whether
	1000, 1250, 1600,
			Thru Sw		MIDI messages received at the
	2000, 2500, 3150,
					MIDI connector will be re-trans-
	4000 Hz
					mitted from the MIDI OUT con-
LOW Gain	-15– +15 dB	Adjusts the gain of the low fre-
					nector (ON) or not (OFF).
		quency. Positive (+) settings			MIDI OUT	MIDI IN
		will emphasize the low-fre-					USB OUT	USB IN
		quency range.
HIGH Freq	2000, 4000, 5000,	Selects the frequency of the high
	6300, 8000,	range.
	10000, 12500,						Sound
	16000, 20000 Hz						Generator
							Section
HIGH Gain	-15– +15 dB	Adjusts the gain of the high fre-					V-Synth XT
		quency. Positive (+) settings				USB-MIDI Thru Sw=OFF
		will emphasize the high-fre-
		quency range.			MIDI OUT	MIDI IN	USB OUT	USB IN
TOTAL	-15– +15 dB	Adjusts the total gain.
Gain
MIDI/USB							Sound
							Section
							Generator
Parameter	Value	Explanation					V-Synth XT
						USB-MIDI Thru Sw=ON
Device ID	17–32	When you want to transmit or re-
			Volume	OFF, ON	Specifies whether received Vol-
		ceive System Exclusive messages,
		set this parameter to match the De-	Expression		ume or Expression Pedal messages
		vice ID number of the other MIDI	Level Con-		will adjust the output volume
		device.	trol		(ON), or will be ignored (OFF).
Clock	INT,	The LFO cycle or multi-effects
Source	MIDI,	changes can be synchronized to a	Chord Memory
	USB MIDI	clock (tempo). When this is used
		by the patch, this Clock Source set-	Parameter	Value	Explanation
		ting determines the clock which
		will be used.	Chord	OFF,	Switches the Multi Chord Memory (one-
		INT: The Patch Tempo will be	Memory	ON	finger chord) function on/off.
		used.	Sw		* If you want to synchronize to an external
		MIDI: Synchronize to the clock of			device, set Clock Source (p. 38) to
		an external MIDI.
					EXTERNAL, then get your external
		USB MIDI: Synchronize to the
					device to transmit clock messages. If you
		clock of an external USB MIDI.
					fail to do this, chords will not play
Rx Sw	OFF, ON	Specifies whether all MIDI mes-			correctly.
		sages will be received (ON) or not	Grid Reso-	Dot-	Each note within the chord will be played
		(OFF).
			lution	ted 8th	separately at the timing interval you
Rx Channel	1–16	Sets the Basic Channel (MIDI chan-		note–	specify here.
		nel on which the VC-2 receives and		64th
		transmits messages).		note
Rx PC	OFF, ON	Specifies whether Program	Code set	C–B	Specify a chord for each key in the range
		Change messages will be received			C–B.
		(ON) or not (OFF).	KEEP	OFF,	When entering a chord from the key-
Rx Bank	OFF, ON	Specifies whether Bank Select mes-		ON	board, this parameter specifies whether
		sages will be received (ON) or not			the keys you press will be held in their
		(OFF).			pressed state (ON) or not (OFF). If this is
Rx Sys-Ex	OFF, ON	Specifies whether System Exclu-			ON, the key will be maintained in a
					“pressed” state even when you release it.
		sive messages will be received
		(ON) or not (OFF).

38