Roland VC-2 owner manual Chorus Parameters, Chorus Type

Page 61

Effects List

Chorus Parameters

The functions of Chorus parameters are explained.

Chorus Type

01: Chorus 1

This conventional chorus effect adds spaciousness and depth to the sound. Slow modulation frequency with less depth.

02:Chorus 2

This conventional chorus effect adds spaciousness and depth to the sound. Rapid modulation frequency with less depth.

03: Chorus 3

This conventional chorus effect adds spaciousness and depth to the sound. Slow modulation frequency with more depth.

04: Chorus 4

This conventional chorus effect adds spaciousness and depth to the sound. Rapid modulation frequency with more depth.

05: Feedback Chorus

This chorus offers a flanger-like effect, creating a soft sound.

06: Flanger

This effect sounds somewhat like a jet airplane taking off and landing.

07: Short Delay

This is a delay with a short delay time.

08: Fbk Short Delay

This is a short delay with many repeats.

Chorus Parameters

Parameter

Value

Description

 

 

 

Pre Low Freq

500–15000 Hz,

Frequency of the low range (TH-

 

THRU

RU: no filter is used)

Pre Hi Freq

THRU, 50–800

Frequency of the high range (TH-

 

Hz

RU: no filter is used)

Pre Dly Time

0–50.0 ms

Adjusts the delay time from the

 

 

direct sound until the chorus

 

 

sound is heard.

Co LPF Freq

500–15000 Hz,

Adjusts the cutoff frequency of

 

THRU

the low pass filter. (THRU: no fil-

 

 

ter is used)

 

 

The effect will be applied to the

 

 

frequency range below the cutoff

 

 

frequency.

Co HPF Freq

THRU, 50–800

Adjusts the cutoff frequency of

 

Hz

the high pass filter. (THRU: no

 

 

filter is used)

 

 

The effect will be applied to the

 

 

frequency range above the cutoff

 

 

frequency.

Rate

0.05–10.0 Hz,

Sets the cycle for the chorus or

 

note

flanger sound undulations.

Depth

0–127

Adjusts the depth of modulation

 

 

for the chorus or flanger.

Feedback

-98– +98 %

Adjusts the proportion of the ef-

 

 

fect sound that is fed back into

 

 

the effect. Negative (-) settings

 

 

will invert the phase.

Cho/Flg Sw

CHORUS,

Selects either chorus or flanger.

 

FLANGER

 

61

Image 61
Contents 03897845 ’05-3-1N Page Page Table of Contents Table of Contents Conventions Used in This Manual Main FeaturesInternal Structure About the VC-2Patch Algorithms Project Memory StructureWork Area/Temporary Area Internal Memory / PC CardMIC Switch VolumePanel Descriptions InputKEY PAD Button Display Power Switch14 E1-E8 knobs PC Card SlotAC Inlet Midi Connectors IN, OUT, ThruInput Jacks L, R Direct OUT Jacks L, RConnect your mic to the front panel MIC jack Making connectionsFig.Q-02.e Starting up VC-2Top Screen of Patch Mode Try Out the Sound Patch modeSelecting a Patch Selecting Patches with the Value dialPlaying Using buttons to select patchesEnabling or Disabling Beep ToneCommon to all patch algorithms Parameters in the Top ScreenIf the patch algorithm is Modeling~ If the patch algorithm is Vocoder~If the patch algorithm is Processor Type If the patch algorithm is Keyboard~Creating Patches Basic Procedure for Patch EditingChanging the Pitch Patch Tune Pulldown menu, touch Data Transfer Transmitting Data to an External Midi Device Data TransferSource, select the type of data that you want to transmit Saving Patches Patch Write Naming a Patch Patch NameAuditioning the Save-Destination Patch Compare Deleting Patches Patch Delete Copying Patch Controller SettingsPatch Controller Copy Top Screen System MIC Setting ScreenNS-COMP PRE-EFX Type Pre-Effect TypesOFF NS-LIMITNoise SUP Carrier ScreenOSC OSC 1/OSC INF1OSC2 Pitch Pitch OSC1 PitchGlide VibratoPortamento KEY AssignCarrier Screen for Processor~ Wave ScreenPoly Pitch Shifter Screen Vocoder ScreenPoly Pitch Shifter ControllerPitch / EQ Growl / TVA / Ctrl Routing Effect ScreenCHO MFXREV MFX TypeImporting Individual Wave Files Wave Import Using Waves Wave ModeCopying a Wave Wave Copy Using the Wave BrowserMoving a Wave Wave Move Exchanging a Wave Wave ExchangeWrite How to Make the System Function SettingsInit Touch SystemFunctions of System Parameters Settings Common to the Entire System Common MasterViewing VC-2’s Information Information Pulldown menu, touch InfoChord Memory MIDI/USBAudio I/F Controller Settings ControllerBreath Loading a Project from Disk Load Project Saving a Project on Disk Save ProjectTouch Execute to execute the Factory Reset Touch Factory ResetFactory Reset screen appears Backing Up Data to Your Computer USB Mode MFX Parameters Effects ListParametric EQ Parametric Equalizer Graphic EQ Graphic EqualizerIsolator and Filter Resonant FilterDistortion / OD Specifications of each Speaker TypeDistortion / Overdrive Amp Simulator Guitar AmpHumanizer Auto WahRecommended combination of pre-amp and speaker Dynamic Processor Stereo Dynamic Processor Stereo DelayTape Echo Simulator Effect has five delays. Each of the Delay Time parameters Multi Tap DelayCan also set the panning and level of each delay sound REO, AlterBand Pass Delay Reverse DelayVocal Echo Delay Pan Type Analog Delay→ChorusDigital Chorus Hexa Chorus Space ChorusAnalog Flanger Boss FlangerStep Flanger Analog PhaserTremolo/Auto Pan Digital PhaserRotary 28 OD/DS→Cho/Flg Overdrive Signal up to one octave up or downDistortion→Chorus/Flanger Stereo Pitch ShifterOverdrive/Distortion→Delay 29 OD/DS→Delay30 Cho/Flg→Delay Chorus/Flanger→Delay31 Enh→Cho/Flg 32 Enh→Delay Enhancer→DelayEnhancer→Chorus/Flanger Vocal MultiLPF Thru Guitar MultiHPF 36 E.Piano Multi Bass MultiPhonograph Keyboard MultiBit Rate Converter Radio TuningPseudo Stereo This effect reproduces the sound of an AM radio playingChorus Type Chorus ParametersChorus Parameters Stereo Plate Reverb ParametersStereo OperaHouse Stereo StudioSpringStereo Room Stereo EchoesStereo Cathedral Stereo ChurchRoom Hall Hall Garage Specifications Midi Implementation Chart CHO IndexVolume System mode Temporary AreaREV Type Reverb type Save Project