Emerson 3081FG instruction manual Navigation, Infrared Remote Control IRC

Page 35

Model 3081FG

Instruction Manual

IB-106-3081 Rev. 1.5 September 2002

d.Navigation

The IRC in Figure 3-6is used to interact with the Model 3081 Transmitter and navi- gate through the screens on the LCD.

1.Hold the IRC within 6 ft (1.8 m) of the Model 3081 Transmitter and within 15 degrees from the centerline of the transmitter LCD. The amount of ambi- ent light may also affect IRC performance.

NOTE

The LCD may react slowly to IRC commands. Allow sufficient time be- tween key presses to avoid undesired or repeated commands from accumu- lating in the command queue.

2.Use the keys on the IRC to navigate through the menu screens. Refer to Figure 3-6.General usage is as follows:

(a)RESET. Returns to the PROCESS DISPLAY screen at the top of the menu tree. Any non-entered num- ber in the exited state will be ig- nored, and the previous data will be used.

(b)HOLD. Not used.

(c)Left/Right Arrow. Moves left and right among editable digits on the display.

(h)ENTER. Initiates the editing proc- ess and causes the most signifi- cant digit of the edited item to start flashing. Also processes the entry so the previous value updates to the new value entered using the ar- row keys. Failure to press ENTER

before exiting a screen will cancel
the input value and revert to the
previous value.	3
	3

(i)NEXT. Accesses the next user screen as shown in the menu tree. Any non-entered number in the ex- ited state will be ignored, and the previous data will be used.

(j)EXIT. Exits from sub-branches of the menu tree where an exit option is explicitly shown. Otherwise, re- turns to the PROCESS DISPLAY screen at the top of the menu tree. Any non-entered number in the ex- ited state will be ignored, and the previous data will be used.

	RESET					HOLD

CAL		ENTER

(d)Up/Down Arrow. Increases or de- creases the value of the currently selected digit on the display.

(e)CAL. Accesses the CALCHECK MENU branch of the menu tree. Only works from the PROCESS DISPLAY screen.

(f)PROG. Accesses the PROGRAM MENU branch of the menu tree. Only works from the PROCESS DISPLAY screen.

(g)DIAG. Accesses the DIAGNOS- TICS MENU branch of the menu tree. Only works from the PROC- ESS DISPLAY screen.

PROG		NEXT


DIAG		EXIT

MODEL 3081

REMOTE CONTROL

ROSEMOUNT

FISHER-ROSEMOUNT

26020032

Figure 3-6. Infrared Remote Control (IRC)

Rosemount Analytical Inc. A Division of Emerson Process Management

Startup and Operation 3-5

Image 35

Contents Model 3081FG Essential Instructions Highlights of Changes Page Model 3081FG Table of ContentsProper Calibration Check Gas Flow Rate List of IllustrationsModel 3081 Transmitter Terminal Block List of TablesModel 3081FG Definitions PrefaceModel 3081FG Component Checklist of Typical System Package Contents Section Description and SpecificationsCode Mounting Adapter Stack Side Product MatrixSystem Description System ConfigurationSystem Overview ScopeSystem Features Handling the Analyzer System Considerations Transmitter Typical System InstallationProbe SpecificationsOperating Load Region Lift OFF Maximum Power Supply VoltageOhms VDCInspect Section InstallationPRE-INSTALLATION Mechanical InstallationSide View Bottom View Front ViewMetal Wall Masonry Wall Stack or Duct Horizontal Probe Installation Adjusting Probe Insertion Depth Model 3081FG Installing Model 3081 Transmitter Mounting Holes Cover LockCircuit Terminal END Block TBElectrical Installation Display Positioning AssemblyThermocouple CELL-WH CELL+BK Model 3081 Transmitter 4-20 mA and Signal ConnectionsTerminal Block Conduit Calibration Check Gas Pneumatic InstallationReference Air Package Instrument Air Reference AirFlow SET MAX Point Knob Mounting Holes Outlet ConnectionOutlet Inlet ConnectionGeneral Power UPSection Startup and Operation Proper Calibration Check Gas Flow Rate Reestablishing Proper Calibration Check GAS Flow RateMenu Tree OperationOverview DisplayProgram DiagnosticsCalcheck MenuNavigation Infrared Remote Control IRCO2 Concentration O2 Concentration Analyzer Access Code Or SecurityAnalyzer Access Code Program MenuCell T HI O2 Concentration Indicator Fault ValueO2 Concentration Upper Cell Temperature Fault Value Upper Range VALSET O2 Filter Time Reset MAX Cell TTo Reset Maximum Cell Temperature O2 Concentration Analyzer Access CodeConcentration SET HI Bottle O2SET LO Bottle O2 Model 3081 Transmitter Parameters SET Code Parameter Range DefaultModel 3081 Transmitter Parameters C mV Diagnostics MenuShow Fault 24. Previous Slope Previous Constant 23. Cell ImpedanceCalcheck Menu SW Build NumberSW Build Date Accept LOW O2 27. in MANUAL?29. Accept LOW O2 Slope Model 3081FG Connections Hart Communicator Signal LineSection HART/AMS OverviewMethod 2, For Load Resistance 250 Ohms Analog Output Device Loop ConnectorsMenu Tree for Hart Communicator TWO-WIRE in Situ Oxygen AnalyzerHart Communicator PC OFF-LINE and ON-LINE OperationsDevice Setup From Sheet Basic Setup Detailed From Sheet Signal Condition Detailed Setup Output Hart Communicator Start CAL- Check Method Model 3081FG PC Board Stack Replacement Section Maintenance and ServiceModel 3081 Electronics Replacement Display Board ReplacementTwo-Wire In Situ Oxygen Analyzer Exploded View Oxygen Probe Replacement Oxygen Probe Terminal Block IMPEDANCE, Ω Section TroubleshootingProbe Life Speed Fault IndicationsOfresponse Thermocouple Identifying and Correcting Fault IndicationsFault 1, Open Thermocouple Fault 3, Shorted Thermocouple Fault 5, O2 Cell Open Fault 6, Cell Impedance Too High Fault 5, O2 Cell Open11. Fault 7, Reversed O2 Cell Fault 7, Reversed O2 CellModel 3081FG Section Return of Material Model 3081FG Index No Part Number Description Replacement PartsReplacement Parts List SectionModel 3081FG Section Index Model 3081FG Model 3081FG Page Section Drawings and Schematics Model 3081FG Warranty Two-Wire In Situ Oxygen Analyzer Serial no Order no