Omron HBP-1300 Installing the Battery Pack, Battery life, Charging time, Low battery

Page 16

Installing the Battery Pack

Warning

If battery fluid comes in contact with the eye, immediately flush with copious amounts of water. Do not rub. Seek medical attention immediately.

Do not use the battery pack in any other device besides this unit. Do not throw into flame, disassemble, or heat.

Caution

Do not short the positive and negative terminals of the battery pack with a wire or other metal object. If battery fluid comes into contact with the skin or clothes, immediately rinse with water.

1. Make sure the AC adapter has been disconnected.

2. Remove the two screws from the top of the rear unit cover, and remove the battery cover.

3. Connect the battery pack to the connector on the monitor, and insert the battery pack into the compartment so that the triangle mark on the battery pack is aligned with the triangle mark on the monitor.

4. Replace the battery cover and secure with screws.

Take care not to pinch the wires when replacing the cover.

5. Connect the AC adapter to the unit and charge the battery pack.

When using the battery pack for the first time, be sure to fully charge (about 4 hours) before using.

Battery life

About 300 measurements are possible with one charge.

A general guideline for replacement of the battery pack is about one year, however, the usage time per charge may grow shorter depending on usage conditions. If you find that the usage time after

each charge has grown shorter and the icon frequently appears, replace the battery pack.

Charging time

Charging automatically starts after the AC adapter is connected.

When a new battery pack or a battery pack that has not been used for a long time is used, some time may elapse before charging starts.

The icon flashes during charging.

Charging is completed in about 4 hours.

Low battery

When the

icon starts flashing, promptly charge the battery pack.

When the icon changes to

, the battery is too low for blood pressure measurement. Charge the

battery.

 

 

Auto Power Off

When the unit is powered by the battery pack, the power automatically turns off after the set time elapses if you forget to turn off the power.

When the unit is used with the AC adapter connected, the “Auto Power Off” setting does not operate.

14

Image 16
Contents HBP-1300 Contents Intended Use IntroductionExemptions General Information Setup Usage warnings and cautionsBefore use / during use Page Cleaning Maintenance and inspectionRechargeable battery Non-Invasive Blood Pressure Nibp measurement For cleaning, see Components of the Product Using the UnitOptions Optional Medical Accessories Features of the ProductKey features, benefits, look Meaning of the Symbols Features / Functions of UnitFront and back of unit LCD Display DIAInstalling the Battery Pack Battery lifeLow battery Auto Power OffConnecting the AC Adapter Battery chargingBattery level AC powerSystem Settings Menu ModePress the Mode button Press the or button to change the settingUtility Mode Confirm that the device is switched offPress the or button to change the auto power off Setting Check the Pressure AccuracyNon-Invasive Blood Pressure Nibp Measurement Non-Invasive Pressure Measurement PrinciplesConnecting the cuff Cuff Selection and ConnectionSelecting the cuff Cuff name Arm circumference InchTo 2 cm Align the artery mark Index Artery with the brachial arteryMeasurement results are displayed Irregular pulse wave detection function Taking the Measurement in Auscultation ModeBody movement detection function Stopping the Measurement Displaying Last ReadingMaintenance Maintenance Inspection and Safety ManagementCleaning of the Device Accessory CareBefore turning on the power When turning on the powerAfter turning on the power Check before UseTroubleshooting Abnormal measurement value Measurement value is questionableError Priority Description Points to check List of Error CodesMedium Internal hardware error Contact Omron Healthcare Other problems Error Priority Cause Solution CodeDisposal DescriptionSpecifications Factory Default SettingsTechnical Specifications HBP-1300 Power supplyEnvironmental Conditions Non-Invasive Blood Pressure NibpPage Manufacturer’s Declaration Emission Test Compliance Electromagnetic EnvironmentRecommend separation distance Separation distance according to frequency of transmitter Manufacturer EU-representativeProduction facility Subsidiary Omron Medizintechnik Handelsgesellschaft mbH
Related manuals
Manual 40 pages 60.07 Kb