GE A071-0CG Mapped DI point not Found. Check config, Mapped do point not Found. Check config

Page 31

ANSI X3.28/SRIO DPA

 

CONFIGURATION GUIDE

GE Energy Services

Mapped DI point not Found. Check config

Cause:

•One of the mapped digital input points could not be located in the SPABUS configuration.

Remedy:

•Ensure none of the Item Table Offsets in A071DIMP are greater than the number of records in the SPABUS item configuration table, A070ITEM.

•Ensure all of the Item Table Offsets in A071DIMP refer only to records in the SPABUS item configuration table, A070ITEM, of type DI, PD, or Spare (-1).

Mapped DO point not Found. Check config

Cause:

•One of the mapped digital output points could not be located in the SPABUS configuration.

Remedy:

•Ensure none of the Item Table Offsets in A071DOMP are greater than the number of records in the SPABUS item configuration table, A070ITEM.

•Ensure all of the Item Table Offsets in A071DOMP refer only to records in the SPABUS item configuration table, A070ITEM, of type DO or Spare (1-).

Mapped EV point not Found. Check config

Cause:

•One of the mapped event data points could not be located in the SPABUS configuration.

Remedy:

•Ensure none of the Item Table Offsets in A071EVMP are greater than the number of records in the SPABUS item configuration table, A070ITEM.

•Ensure all of the Item Table Offsets in A071EVMP refer only to records in the SPABUS item configuration table, A070ITEM, of type EV or Spare (-1).

Missing Configuration ... Deleting

Cause:

•The system was unable to locate the main configuration table for the ANSI X3.28/SRIO DPA.

Remedy:

•Ensure the main configuration table, A071MAIN, exists in the configuration and is comprised of a single record.

Restricted

A071-0CG-2.02-2

Full

19

 

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Ansi X3.28/SRIO DPA Trademark Notices Table of Contents Ansi X3.28/SRIO DPA List of Figures System Overview Xii Read Access FlagsAnsi X3.28/SRIO DPA List of Tables Viii Purpose of this Guide About this GuideWho Should Use this Guide Additional Documentation Product Perspective OverviewXii Ansi X3.28/SRIO DPA Configuration Tables Configuring TablesConfiguration Sequence Character Times Configuring the Main Table A071MAINAnsi X3.28/SRIO DPA GE Energy Services Baud Rate One Character Time ms Configuring the Mapping Tables Mapping Table Configuration Parameters Log-In User B014USER Configuring Wesmaint for the Ansi X3.28/SRIO DPARead Access Flags Ansi Application process died Appendix AError MessagesError Messages Fatal Error MessagesCant get enough memory for Ansi Application. Suspending Cant allocate rx sinksCant create required exchanges. Suspending Cant create T071 exchangeCant spawn/activate L071 process Cant set communications timersCant set configured bit rate Cant spawn/activate E071 processInvalid checksum configured Bcc or Crc Invalid AI offset configuredInvalid Analog Format configured 32 BIN, 6 or 3 BCD Invalid AO offset configuredInvalid embedded response enable Yes or No Invalid DD offset configuredInvalid DI offset configured Invalid do offset configuredInvalid OBJ offset configured Invalid Evnt offset configuredInvalid EV offset configured Invalid modem enable Yes or NoInvalid Retransmit digital configured -1 to Invalid parity configured None, Even, OddInvalid PD offset configured Invalid Retransmit analog configured -1 toMapped AO point not Found. Check config Invalid SYS offset configuredInvalid TM offset configured Mapped AI point not Found. Check configMissing Configuration ... Deleting Mapped DI point not Found. Check configMapped do point not Found. Check config Mapped EV point not Found. Check configAnsi X3.28/SRIO DPA Ascii Glossary of TermsWIN List of Acronyms and Abbreviations
Top Page Image Contents