Cortelco 2740 Connect Cords to Telephone, Verify Proper Installation, Station NumberAssignment

Page 10

1.3.9Connect Cords to Telephone

If the wall jack is labeled Lines 1 & 2, connect the short telephone line cord to the jack on the telephone labeled L1/L2. If the wall jack is labeled Lines 3 & 4, connect the short cord to the jack on the telephone labeled L3/L4. Connect the long telephone line cord to the other line jack on the telephone and thread it through its long groove on the bottom of the phone, then plug the AC power cord into the adapter jack on the bottom of the telephone, threading the power cord through its long groove on the bottom of the phone. Thread the short telephone cord through the square hole in the center of the wall mount bracket, and then attach the wall mount bracket to the base of the telephone.

1.3.10 Verify Proper Installation

The following procedure should be used at each telephone to check for proper installation.Also use this procedure any time you are experiencing difficulty. The phone must be connected to theAC power supply, line 1 must be connected to the line 1 jack, and the phone must have been assigned an intercom station number.

First, verify that line 1 is connected to the same telephone number at all the telephones. To do this, press the line 1 button at one of the telephones. The line 1 LED should be green, the speakerphone LED should be red, and dial tone should be heard from the speaker. Now go to each of the other stations and make sure that each line 1 LED is red. Next, make sure that lines 2, 3 and 4 are connected the same at all the phones by performing the following steps at each telephone:

1.Press the line 1 button. The line 1 LED should be green, the speakerphone LED should be red, and dial tone should be heard from the speaker.

2.Dial the telephone number for line 2. The line 2 LED should flash slowly. If the line 2 LED does not flash, then line 2 is improperly connected to this telephone.

3.If this telephone utilizes line 3 and/or line 4, repeat steps 1 and 2, substituting the respective phone number(s) in step 2.

2.SYSTEM PROGRAMMING

2.1Station NumberAssignment

Each station must be assigned a different station number.

To assign a number to a station:

a.Press MENU. The display will read “Phone Setting”

b.Press the soft key under ENTER. The display will show the currently assigned station number.

c.Press the soft key under CHANGE repeatedly, until the desired station number is displayed. The choices are Station #01 through Station #16.

d.Press MENU to exit.

Until a telephone is assigned a station number, the telephone will not operate. To assign this tele- phone a station number, simply press the soft key under CHANGE repeatedly until the desired station number is displayed.

Note: One phone in the system must be set as Station #01 in order for all the system features, such as shared directory dial, to function.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents OWNER’S Instruction Manual Table of Contents Using standard telephones Thank YOU For Purchasing Important Safety Instructions Unpacking and Installation Box ContentsTelephone Part Identification Standard Installation Installation Identify Your Existing Wiring SystemPlan Your Installation Installations with Private Lines and Unconnected LinesInstall Batteries Optional Assign a Station NumberConnect Cords to Telephone Verify Proper InstallationStation NumberAssignment Station Name Assignment ChangeCommon Line ConfigurationLoop Voltage Detector Setting Distinctive Ringing Ringer ConfigurationTo choose how each line will ring Setting Off-Hook Ringing Intercom Call Response and PagingTo block pages at your telephone To choose how your phone will respond to intercom callsAutomatic Line Selection Toll Restriction To completely restrict specific lines at a telephone To set the allowed numbers at a particular telephoneDialing Mode To Change the Privacy Setting At Station #01System Privacy To enter HOME, LOCAL, and 1 Plus 7 area codes Memory FeaturesArea Codes Storing a hyphen into memoryStoring a Caller ID number into memory Storing temporary tone dialing into memoryStoring one of the last five numbers dialed into memory To store a memory dial numberTo Store Caller ID Calls To Store the Centrex prefixPress Down Arrow Message Waiting Mode SelectionTime and Date Message Waiting LampCaller ID on Call Waiting Cidcw Sensitivity Adjusting Auto Hold Drop TimeAdjusting Flash Length Held Call ReminderErase Toll Restrictions At station #01 Erase All Feature SettingsErase Numbers Stored in Memory Making and Answering CallsHold Placing a Call on Hold Redial To redial the last phone number dialedTo redial any of the last five phone numbers dialed Making a call on another lineOutside Call with Intercom Station ConferenceOutside Calls Transfer Attended TransferCaller ID Transfer RingPersonal Ring Incoming callDeleting Numbers Volume LevelsVoice Mail Message Waiting Accessing Messages RingerMute Resetting MSG LampFlash Do Not Disturb DNDToll Restriction Removal Single Call Line ReserveCall Privacy Toll Restriction Removal Single StationElapsed Call Time Previous Calls Timer Elapsed Call TimeTimer Reset HeadsetIntercom Calls Personal DirectoryPredialing Intercom while IdleAnswering an Intercom Call while on an Outside Call Intercom VoiceIntercom Handsfree PagingIntercom Line Status and Calls on HoldFax Machines and Modems Power Failure Operation Battery ReplacementOutlet that is not controlled by a wall switch Phone Setting Menu Top LevelMenu Option SUB Menu Default Available OPTIONS/COMMENT Memory Setting Menu Time/Date SetAdvanced Setting Option FCC Information Telephone Repair Limited Warranty
Top Page Image Contents