Radio Shack 43-3704 owner manual Base downward to secure it

Page 10

Installation

To remove, push up

a tab on the wall

mount adapter as shown.

1.Make the AC adapter and the short telephone line cord through the hole on the bracket.

2.Plug one end of the modular cord into the TEL LINE 1/2 jack on the back of the base.

3.Insert the supplied AC adapter’s barrel plug into the DC IN 9V jack on the back of the base.

4.Slide the bracket into the notches on the base.

5.Plug the adapter into a standard AC outlet. Hook the cord on the notch of the bracket.

6.Plug the telephone line cord into the telephone outlet.

7.For a wall plate,

align the base’s keyhole slots with the wall plate studs and slide the base

downward to secure it.

For direct wall mounting, align the base’s keyhole slots with the mounting screws and slide

the base downward to secure it.

10

Image 10

Contents 43-3704 Contents Introduction Information FCC StatementSurge Protection Important Safety Instructions Read this Before Installation Important Caller ID InformationInstallation Selecting a LocationOn a Desk Top On a Wall Plate or WallBase downward to secure it Recharging the Battery Pack CONNECTING/CHARGING the Battery PackInstallation To attach the beltclip Installing a BeltclipUsing a Headset To remove the beltclipDisplay and Icons Example of the standby mode displayAnimation Displays Talk mode Soft KEY FunctionDefault Settings Main Menu OptionsUsing the Interface Setting Menu OptionsDirectLink Mode Using DirectLink ModeRoom Monitor Handset SetupUsing Room Monitor Confirmation tone, and DirectLinkPress the OK soft key. You will hear a confirmation tone Selecting a Ringer VolumeSelecting a Ringer Tone Distinctive Ringer Setup Setting the Anykey Answer Setting the AutoTalkSetting the True Banner Setting the Key Touch Tone Selecting a LanguageSetting the Animation Screen Setting Room MonitorSetting a PIN Code Answering System SetupSetting the Ring Time Setting the Record Time Turning the message alert tone off by pressing any key Setting the Language of your Answering SystemTurning the message alert tone off from a remote location Setting the Call Screen Global SetupSetting Day and Time Setting Cidcw Caller ID on Call Waiting Setting the Area CodeSetting the Dial Mode DE-REGISTER the Handset Using Your PhoneFrom the handset Making a CallFrom the Handset Speakerphone Receiving a CallCall Waiting Switching to the Handset Speakerphone During a CallHanging UP Placing a Call on HoldDeleting a Redial Record Storing a Redial RecordAdjusting the Handset Earpiece and Speaker Volume Do not Disturb DNDMute Microphone Tone Dialing Switch OverPrivacy Mode Travelling OUT-OF-RANGEConferencing with 2 outside lines Joining a Conference CallConferencing with one outside line ConferencingFlash and Call Waiting Find HandsetPhonebook Storing Phone Numbers NAMES, Distinctive Rings Speed DialSteps for Entering Names and Special Characters Speed Dial appears. PressViewing the Phonebook If you make a mistake while entering a nameTo finish the viewing operation, press Making Calls Using the PhonebookSpeed Dialing To hang up press ENDEditing or Erasing a Data Editing the Stored DataCopying Phonebook Locations Deleting the Stored DataTesting Stored Emergency Numbers Caller ID Caller ID and Cidcw Caller ID on Call WaitingViewing the Caller ID List Deleting all Caller ID names/ numbers Using the Caller ID Message ListDeleting Information from the Caller ID List Calling a party from the Caller ID listViewing the Caller ID List on Long Distance calls and Area Code Setting/CancellationStoring Caller ID messages in the Phonebook Call Waiting Deluxe Features Dual Handset Expandability Expanding Your PhoneRegister the Handset to the Base INTERCOM/CALL Transfer Feature Using the Directlink ModeDirectLink call Intercom Call Transfer FeatureFrom handset to handset Expanding Your Phone Features Integrated Answering DevicePre-recorded message Setting your outgoing message GreetingSetting UP Your Answering System Ô Recording a personal outgoing message GreetingChoosing between the two outgoing messages Adjusting the Speaker Volume LevelDeleting an outgoing message LED stops flashing when all new messages are played back Answering System SettingsSetting the Time REPEAT/SELECT until you hear the correct hour settingSetting a PIN code Setting the ring timeSelecting the message record time Press CLOCK/MENU three timesSetting the message alert Announce only featurePress SET Confirmation tone sounds, the system Selecting the language From the base Setting the call screenScreening a call To screen an incoming call, do the steps as followsPlaying your messages Using Your Answering SystemTo cancel the call screen, press END From the handsetRepeating a message Deleting a message Skipping a messageTo maintain maximum record time, delete the old messages. Ô Recording a conversation Voice memoSystem returns to standby Remote access away from home Remote OperationFunction Remote access with the handset Remote Key Function ∅/4 Deleting a Message Stop Operation ÔTroubleshooting Symptom SuggestionKeep the handset away from microwave ovens Service and Repair CarePage Memo RadioShack Corporation Fort Worth, Texas