Radio Shack 43-3704 owner manual Intercom, Call Transfer Feature, From handset to handset

Page 52

Expanding Your Phone

Intercom

1.Press INTCM/HOLD in standby mode.

2.Select the handset you want to talk with from the selection list within 30 seconds. To select the handset, press

CID/VOL/ or REDIAL/P/ , and then press the OK key. If you select All, all handsets will be paged. An intercom tone sounds.

To Cancel intercom press the CANCEL soft key on the initiating handset.

3.On the receiving handset to answer the call, press TALK/FLASH, the ANSWER soft key or INTCM/HOLD. Or press any number key, /TONE/< or #/> (when Anykey Answer is on), or pick up the handset from the cradle (when AutoTalk is on).

4.To hang up the intercom call, press END or the END soft key on either handset.

Call Transfer Feature

From handset to handset

1.During a call, press INTCM/HOLD on the handset.

The line soft key (LINE1 or LINE2) to be placed on hold will flash. The Call will be put on hold.

2.Select a handset to transfer the call within ten seconds. (Refer to step 2 in the intercom section on page 52).

The call will automatically be placed on hold, and an intercom tone sounds. To cancel the transfer, press

TALK/FLASH or SPEAKER on the initiating handset.

52

Image 52
Contents 43-3704 Contents Introduction Information FCC StatementSurge Protection Important Safety Instructions Read this Before Installation Important Caller ID InformationInstallation Selecting a LocationOn a Desk Top On a Wall Plate or WallBase downward to secure it Recharging the Battery Pack CONNECTING/CHARGING the Battery PackInstallation Installing a Beltclip Using a HeadsetTo attach the beltclip To remove the beltclipDisplay and Icons Example of the standby mode displayAnimation Displays Talk mode Soft KEY FunctionDefault Settings Main Menu OptionsSetting Menu Options DirectLink ModeUsing the Interface Using DirectLink ModeHandset Setup Using Room MonitorRoom Monitor Confirmation tone, and DirectLinkPress the OK soft key. You will hear a confirmation tone Selecting a Ringer VolumeSelecting a Ringer Tone Distinctive Ringer Setup Setting the Anykey Answer Setting the AutoTalkSetting the True Banner Setting the Key Touch Tone Selecting a LanguageSetting the Animation Screen Setting Room MonitorSetting a PIN Code Answering System SetupSetting the Ring Time Setting the Record Time Turning the message alert tone off by pressing any key Setting the Language of your Answering SystemTurning the message alert tone off from a remote location Setting the Call Screen Global SetupSetting Day and Time Setting Cidcw Caller ID on Call Waiting Setting the Area CodeSetting the Dial Mode Using Your Phone From the handsetDE-REGISTER the Handset Making a CallFrom the Handset Speakerphone Receiving a CallSwitching to the Handset Speakerphone During a Call Hanging UPCall Waiting Placing a Call on HoldDeleting a Redial Record Storing a Redial RecordAdjusting the Handset Earpiece and Speaker Volume Do not Disturb DNDTone Dialing Switch Over Privacy ModeMute Microphone Travelling OUT-OF-RANGEJoining a Conference Call Conferencing with one outside lineConferencing with 2 outside lines ConferencingFlash and Call Waiting Find HandsetPhonebook Storing Phone Numbers NAMES, Distinctive Rings Speed DialSteps for Entering Names and Special Characters Speed Dial appears. PressViewing the Phonebook If you make a mistake while entering a nameMaking Calls Using the Phonebook Speed DialingTo finish the viewing operation, press To hang up press ENDEditing or Erasing a Data Editing the Stored DataCopying Phonebook Locations Deleting the Stored DataTesting Stored Emergency Numbers Caller ID Caller ID and Cidcw Caller ID on Call WaitingViewing the Caller ID List Using the Caller ID Message List Deleting Information from the Caller ID ListDeleting all Caller ID names/ numbers Calling a party from the Caller ID listViewing the Caller ID List on Long Distance calls and Area Code Setting/CancellationStoring Caller ID messages in the Phonebook Call Waiting Deluxe Features Dual Handset Expandability Expanding Your PhoneRegister the Handset to the Base INTERCOM/CALL Transfer Feature Using the Directlink ModeDirectLink call Intercom Call Transfer FeatureFrom handset to handset Expanding Your Phone Features Integrated Answering DeviceSetting your outgoing message Greeting Setting UP Your Answering System ÔPre-recorded message Recording a personal outgoing message GreetingChoosing between the two outgoing messages Adjusting the Speaker Volume LevelDeleting an outgoing message Answering System Settings Setting the TimeLED stops flashing when all new messages are played back REPEAT/SELECT until you hear the correct hour settingSetting a PIN code Setting the ring timeSelecting the message record time Press CLOCK/MENU three timesSetting the message alert Announce only featurePress SET Confirmation tone sounds, the system Selecting the language Setting the call screen Screening a callFrom the base To screen an incoming call, do the steps as followsUsing Your Answering System To cancel the call screen, press ENDPlaying your messages From the handsetRepeating a message Deleting a message Skipping a messageTo maintain maximum record time, delete the old messages. Ô Recording a conversation Voice memoSystem returns to standby Remote access away from home Remote OperationFunction Remote access with the handset Remote Key Function ∅/4 Deleting a Message Stop Operation ÔTroubleshooting Symptom SuggestionKeep the handset away from microwave ovens Service and Repair CarePage Memo RadioShack Corporation Fort Worth, Texas