Radio Shack 43-3704 owner manual

Page 74

Note about Handset-Base Registration

NOTE ABOUT HANDSET-BASE REGISTRATION

When you register the handset with the base, unique data is written on both the base and the handset. The handset registered to one base unit cannot be used with other base unit unless the registration data is “de- registered” with the original base unit. This means the handset must be within the range of the original base unit to de-register. If for any reason the original base unit is not within the range (or the registration data in the original base unit is erased), “Out of Range” error takes place and you cannot de-register the handset.

Should you encounter this trouble, follow these steps to individually de- register the handset and the base.

1.Remove the handset if it sits on the base.

2.On the handset, press and hold END and # at the same time until you hear beep.

3.Disconnect the AC adapter.

4.While holding PAGE, connect the AC adapter. Keep pressing PAGE until the CHARGE LED starts to blink.

5.Place the handset on the base and wait until the CHARGE LED stops flashing.

This erases all the handset registration data on the base, not limited to the handset you placed at Step 5 above. You need to register other handset(s) also if you have more than one. First de-register the handset as in Step 1 above, and then place it on the base.

If you have trouble in de-registration, take your base and handset (including extra handset(s) if you have) to your local RadioShack or call 1-800-The Shack (843-7422) for assistance.

Also, when you request repair or service, please be sure to bring in the entire system (including extra handset if used) so we can keep your registration data intact.

74

Image 74

Contents 43-3704 Contents Introduction Information FCC StatementSurge Protection Important Safety Instructions Read this Before Installation Important Caller ID InformationInstallation Selecting a LocationOn a Desk Top On a Wall Plate or WallBase downward to secure it Recharging the Battery Pack CONNECTING/CHARGING the Battery PackInstallation To attach the beltclip Installing a BeltclipUsing a Headset To remove the beltclipAnimation Displays Example of the standby mode displayDisplay and Icons Talk mode Soft KEY FunctionDefault Settings Main Menu OptionsUsing the Interface Setting Menu OptionsDirectLink Mode Using DirectLink ModeRoom Monitor Handset SetupUsing Room Monitor Confirmation tone, and DirectLinkSelecting a Ringer Tone Selecting a Ringer VolumePress the OK soft key. You will hear a confirmation tone Distinctive Ringer Setup Setting the True Banner Setting the AutoTalkSetting the Anykey Answer Setting the Key Touch Tone Selecting a LanguageSetting the Animation Screen Setting Room MonitorSetting the Ring Time Answering System SetupSetting a PIN Code Setting the Record Time Turning the message alert tone off from a remote location Setting the Language of your Answering SystemTurning the message alert tone off by pressing any key Setting Day and Time Global SetupSetting the Call Screen Setting Cidcw Caller ID on Call Waiting Setting the Area CodeSetting the Dial Mode DE-REGISTER the Handset Using Your PhoneFrom the handset Making a CallFrom the Handset Speakerphone Receiving a CallCall Waiting Switching to the Handset Speakerphone During a CallHanging UP Placing a Call on HoldDeleting a Redial Record Storing a Redial RecordAdjusting the Handset Earpiece and Speaker Volume Do not Disturb DNDMute Microphone Tone Dialing Switch OverPrivacy Mode Travelling OUT-OF-RANGEConferencing with 2 outside lines Joining a Conference CallConferencing with one outside line ConferencingFlash and Call Waiting Find HandsetPhonebook Storing Phone Numbers NAMES, Distinctive Rings Speed DialSteps for Entering Names and Special Characters Speed Dial appears. PressViewing the Phonebook If you make a mistake while entering a nameTo finish the viewing operation, press Making Calls Using the PhonebookSpeed Dialing To hang up press ENDEditing or Erasing a Data Editing the Stored DataCopying Phonebook Locations Deleting the Stored DataTesting Stored Emergency Numbers Caller ID Caller ID and Cidcw Caller ID on Call WaitingViewing the Caller ID List Deleting all Caller ID names/ numbers Using the Caller ID Message ListDeleting Information from the Caller ID List Calling a party from the Caller ID listStoring Caller ID messages in the Phonebook Long Distance calls and Area Code Setting/CancellationViewing the Caller ID List on Call Waiting Deluxe Features Register the Handset to the Base Expanding Your PhoneDual Handset Expandability DirectLink call Using the Directlink ModeINTERCOM/CALL Transfer Feature From handset to handset Call Transfer FeatureIntercom Expanding Your Phone Features Integrated Answering DevicePre-recorded message Setting your outgoing message GreetingSetting UP Your Answering System Ô Recording a personal outgoing message GreetingDeleting an outgoing message Adjusting the Speaker Volume LevelChoosing between the two outgoing messages LED stops flashing when all new messages are played back Answering System SettingsSetting the Time REPEAT/SELECT until you hear the correct hour settingSetting a PIN code Setting the ring timeSelecting the message record time Press CLOCK/MENU three timesPress SET Confirmation tone sounds, the system Announce only featureSetting the message alert Selecting the language From the base Setting the call screenScreening a call To screen an incoming call, do the steps as followsPlaying your messages Using Your Answering SystemTo cancel the call screen, press END From the handsetRepeating a message To maintain maximum record time, delete the old messages. Ô Skipping a messageDeleting a message System returns to standby Voice memoRecording a conversation Remote access away from home Remote OperationFunction Remote access with the handset Remote Key Function ∅/4 Deleting a Message Stop Operation ÔTroubleshooting Symptom SuggestionKeep the handset away from microwave ovens Service and Repair CarePage Memo RadioShack Corporation Fort Worth, Texas