Radio Shack 43-3704 owner manual Expanding Your Phone, Dual Handset Expandability

Page 50

Expanding Your Phone

! IMPORTANT !

If you purchase a 43-3705 extra handset, please register the handset to the original/main base before use. The 43-3705 will not operate until it is registered.

Ô NOTES Ô

•All of the handsets ring when a call is received.

•An extra handset can be registered when the main base is in standby mode.

EXPANDING YOUR PHONE

Dual Handset Expandability

Your phone supports another handset in addition to the supplied. You can now place a fully-featured cordless handset anywhere AC power is available to connect the handset charger. !

Handsets can be used in DirectLink Mode or on an intercom call without interfering with incoming calls. It is possible to have a four-way conference among two handsets and both outside lines. All of the handsets ring when a call is received.

REGISTER THE HANDSET TO THE BASE

If you purchase an extra handset, you need to register the handset to the base before use. Only one handset can be registered at a time. ! Ô

Handset supplied with the phone is registered to the base by the factory. When charged, pre-registered handset displays a handset ID number. Handset that has not been registered displays Place handset on main base to register. When you register an extra handset to the base, the handset ID will be assigned.

1.Before registering the extra handset, the battery pack MUST be charged for 15-20 hours.

2.Place the extra handset in the main base unit to begin registration.

3.While the handset is registering,

Handset Registering will appear in the LCD.

50

Image 50

Contents 43-3704 Contents Introduction Information FCC StatementSurge Protection Important Safety Instructions Read this Before Installation Important Caller ID InformationInstallation Selecting a LocationOn a Desk Top On a Wall Plate or WallBase downward to secure it Recharging the Battery Pack CONNECTING/CHARGING the Battery PackInstallation To attach the beltclip Installing a BeltclipUsing a Headset To remove the beltclipAnimation Displays Example of the standby mode displayDisplay and Icons Talk mode Soft KEY FunctionDefault Settings Main Menu OptionsUsing the Interface Setting Menu OptionsDirectLink Mode Using DirectLink ModeRoom Monitor Handset SetupUsing Room Monitor Confirmation tone, and DirectLinkSelecting a Ringer Tone Selecting a Ringer VolumePress the OK soft key. You will hear a confirmation tone Distinctive Ringer Setup Setting the True Banner Setting the AutoTalkSetting the Anykey Answer Setting the Key Touch Tone Selecting a LanguageSetting the Animation Screen Setting Room MonitorSetting the Ring Time Answering System SetupSetting a PIN Code Setting the Record Time Turning the message alert tone off from a remote location Setting the Language of your Answering SystemTurning the message alert tone off by pressing any key Setting Day and Time Global SetupSetting the Call Screen Setting Cidcw Caller ID on Call Waiting Setting the Area CodeSetting the Dial Mode DE-REGISTER the Handset Using Your PhoneFrom the handset Making a CallFrom the Handset Speakerphone Receiving a CallCall Waiting Switching to the Handset Speakerphone During a CallHanging UP Placing a Call on HoldDeleting a Redial Record Storing a Redial RecordAdjusting the Handset Earpiece and Speaker Volume Do not Disturb DNDMute Microphone Tone Dialing Switch OverPrivacy Mode Travelling OUT-OF-RANGEConferencing with 2 outside lines Joining a Conference CallConferencing with one outside line ConferencingFlash and Call Waiting Find HandsetPhonebook Storing Phone Numbers NAMES, Distinctive Rings Speed DialSteps for Entering Names and Special Characters Speed Dial appears. PressViewing the Phonebook If you make a mistake while entering a nameTo finish the viewing operation, press Making Calls Using the PhonebookSpeed Dialing To hang up press ENDEditing or Erasing a Data Editing the Stored DataCopying Phonebook Locations Deleting the Stored DataTesting Stored Emergency Numbers Caller ID Caller ID and Cidcw Caller ID on Call WaitingViewing the Caller ID List Deleting all Caller ID names/ numbers Using the Caller ID Message ListDeleting Information from the Caller ID List Calling a party from the Caller ID listStoring Caller ID messages in the Phonebook Long Distance calls and Area Code Setting/CancellationViewing the Caller ID List on Call Waiting Deluxe Features Register the Handset to the Base Expanding Your PhoneDual Handset Expandability DirectLink call Using the Directlink ModeINTERCOM/CALL Transfer Feature From handset to handset Call Transfer FeatureIntercom Expanding Your Phone Features Integrated Answering DevicePre-recorded message Setting your outgoing message GreetingSetting UP Your Answering System Ô Recording a personal outgoing message GreetingDeleting an outgoing message Adjusting the Speaker Volume LevelChoosing between the two outgoing messages LED stops flashing when all new messages are played back Answering System SettingsSetting the Time REPEAT/SELECT until you hear the correct hour settingSetting a PIN code Setting the ring timeSelecting the message record time Press CLOCK/MENU three timesPress SET Confirmation tone sounds, the system Announce only featureSetting the message alert Selecting the language From the base Setting the call screenScreening a call To screen an incoming call, do the steps as followsPlaying your messages Using Your Answering SystemTo cancel the call screen, press END From the handsetRepeating a message To maintain maximum record time, delete the old messages. Ô Skipping a messageDeleting a message System returns to standby Voice memoRecording a conversation Remote access away from home Remote OperationFunction Remote access with the handset Remote Key Function ∅/4 Deleting a Message Stop Operation ÔTroubleshooting Symptom SuggestionKeep the handset away from microwave ovens Service and Repair CarePage Memo RadioShack Corporation Fort Worth, Texas