Radio Shack 43-3704 owner manual Editing or Erasing a Data, Editing the Stored Data

Page 42

Phonebook

feature. When the phone is in standby mode, press and hold a number key (0-9) associated with the speed dial until the phone number appears and then press TALK/FLASH or SPEAKER. The phone will automatically select a free line. To select a particular line, press the LINE1 or LINE2 soft key. The number stored in the speed dial (SPD1 - SPD0) is dialed.

EDITING OR ERASING A DATA

1.When the phone is in standby mode, press MUTE .

To delete all phonebook locations, press the DELETE soft key. Delete All? appears. Use CID/VOL/ or REDIAL/P/

to select Yes, and then press the OK soft key. You will hear a confirmation tone.

2.Press CID/VOL/ or REDIAL/P/ , or the number keypad to view the phonebook locations (see “Viewing the Phonebook” on page 40).

a.Editing the Stored Data

1.When the phonebook location to be edited appears, press the EDIT soft key.

Press CID/VOL/ or REDIAL/P/ to select Edit?, and then the OK soft key.

2.Follow the steps 3 to 7 under “Storing Phone Numbers, Names, Distinctive Rings, and Speed Dial” on page 38-39 to complete the editing operation.

3.Press the OK soft key. You will hear a confirmation tone.

42

Image 42

Contents 43-3704 Contents Introduction Information FCC StatementSurge Protection Important Safety Instructions Read this Before Installation Important Caller ID InformationInstallation Selecting a LocationOn a Desk Top On a Wall Plate or WallBase downward to secure it Recharging the Battery Pack CONNECTING/CHARGING the Battery PackInstallation To attach the beltclip Installing a BeltclipUsing a Headset To remove the beltclipExample of the standby mode display Display and IconsAnimation Displays Talk mode Soft KEY FunctionDefault Settings Main Menu OptionsUsing the Interface Setting Menu OptionsDirectLink Mode Using DirectLink ModeRoom Monitor Handset SetupUsing Room Monitor Confirmation tone, and DirectLinkSelecting a Ringer Volume Press the OK soft key. You will hear a confirmation toneSelecting a Ringer Tone Distinctive Ringer Setup Setting the AutoTalk Setting the Anykey AnswerSetting the True Banner Setting the Key Touch Tone Selecting a LanguageSetting the Animation Screen Setting Room MonitorAnswering System Setup Setting a PIN CodeSetting the Ring Time Setting the Record Time Setting the Language of your Answering System Turning the message alert tone off by pressing any keyTurning the message alert tone off from a remote location Global Setup Setting the Call ScreenSetting Day and Time Setting Cidcw Caller ID on Call Waiting Setting the Area CodeSetting the Dial Mode DE-REGISTER the Handset Using Your PhoneFrom the handset Making a CallFrom the Handset Speakerphone Receiving a CallCall Waiting Switching to the Handset Speakerphone During a CallHanging UP Placing a Call on HoldDeleting a Redial Record Storing a Redial RecordAdjusting the Handset Earpiece and Speaker Volume Do not Disturb DNDMute Microphone Tone Dialing Switch OverPrivacy Mode Travelling OUT-OF-RANGEConferencing with 2 outside lines Joining a Conference CallConferencing with one outside line ConferencingFlash and Call Waiting Find HandsetPhonebook Storing Phone Numbers NAMES, Distinctive Rings Speed DialSteps for Entering Names and Special Characters Speed Dial appears. PressViewing the Phonebook If you make a mistake while entering a nameTo finish the viewing operation, press Making Calls Using the PhonebookSpeed Dialing To hang up press ENDEditing or Erasing a Data Editing the Stored DataCopying Phonebook Locations Deleting the Stored DataTesting Stored Emergency Numbers Caller ID Caller ID and Cidcw Caller ID on Call WaitingViewing the Caller ID List Deleting all Caller ID names/ numbers Using the Caller ID Message ListDeleting Information from the Caller ID List Calling a party from the Caller ID listLong Distance calls and Area Code Setting/Cancellation Viewing the Caller ID List onStoring Caller ID messages in the Phonebook Call Waiting Deluxe Features Expanding Your Phone Dual Handset ExpandabilityRegister the Handset to the Base Using the Directlink Mode INTERCOM/CALL Transfer FeatureDirectLink call Call Transfer Feature IntercomFrom handset to handset Expanding Your Phone Features Integrated Answering DevicePre-recorded message Setting your outgoing message GreetingSetting UP Your Answering System Ô Recording a personal outgoing message GreetingAdjusting the Speaker Volume Level Choosing between the two outgoing messagesDeleting an outgoing message LED stops flashing when all new messages are played back Answering System SettingsSetting the Time REPEAT/SELECT until you hear the correct hour settingSetting a PIN code Setting the ring timeSelecting the message record time Press CLOCK/MENU three timesAnnounce only feature Setting the message alertPress SET Confirmation tone sounds, the system Selecting the language From the base Setting the call screenScreening a call To screen an incoming call, do the steps as followsPlaying your messages Using Your Answering SystemTo cancel the call screen, press END From the handsetRepeating a message Skipping a message Deleting a messageTo maintain maximum record time, delete the old messages. Ô Voice memo Recording a conversationSystem returns to standby Remote access away from home Remote OperationFunction Remote access with the handset Remote Key Function ∅/4 Deleting a Message Stop Operation ÔTroubleshooting Symptom SuggestionKeep the handset away from microwave ovens Service and Repair CarePage Memo RadioShack Corporation Fort Worth, Texas