Radio Shack 43-3704 Answering System Settings, Setting the Time, Press SET to select the hour

Page 57

NEW MESSAGE LED

The new message LED on the handset is designed to work with your answering system. The LED flashes when you have new messages in your answering system.

The LED stops flashing when all new messages are played back

Answering System Settings

To set the following seven functions you must enter the menu mode. Ô

Setting the Time

Follow these steps to set the clock on the answering system to the correct time. Ô

1.Press CLOCK/MENU.

2.Press SKIP/SELECT or

REPEAT/SELECT until the correct day is announced and the corresponding number (from 1 Sunday to 7 Saturday) appears.

3.Press SET to select the day.

4.Press SKIP/SELECT or

REPEAT/SELECT until you hear the correct hour setting.

The numbers 1 through 12 appear on the base as each hour is announced.

5.Press SET to select the hour.

6.Press SKIP/SELECT or

REPEAT/SELECT until you hear the correct minute setting.

The numbers 00 through 59 appears on the base as each minute is announced.

7. Press SET to select the minute.

Ô NOTES Ô

Answering System

Settings

•For your convenience, voice prompts will guide you through the menu setup mode.

•A confirmation tone sounds to indicate standby mode.

•You can also set these menus from the handset. See “Answering System Setup” on page 24 for instructions.

Setting the Time Time stamp will not be

heard until you have set the time.

The Integrated Answering Device

57

Image 57

Contents 43-3704 Contents Introduction FCC Statement InformationSurge Protection Important Safety Instructions Important Caller ID Information Read this Before InstallationSelecting a Location InstallationOn a Wall Plate or Wall On a Desk TopBase downward to secure it CONNECTING/CHARGING the Battery Pack Recharging the Battery PackInstallation Using a Headset Installing a BeltclipTo attach the beltclip To remove the beltclipExample of the standby mode display Display and IconsAnimation Displays Soft KEY Function Talk modeMain Menu Options Default SettingsDirectLink Mode Setting Menu OptionsUsing the Interface Using DirectLink ModeUsing Room Monitor Handset SetupRoom Monitor Confirmation tone, and DirectLinkSelecting a Ringer Volume Press the OK soft key. You will hear a confirmation toneSelecting a Ringer Tone Distinctive Ringer Setup Setting the AutoTalk Setting the Anykey AnswerSetting the True Banner Selecting a Language Setting the Key Touch ToneSetting Room Monitor Setting the Animation ScreenAnswering System Setup Setting a PIN CodeSetting the Ring Time Setting the Record Time Setting the Language of your Answering System Turning the message alert tone off by pressing any keyTurning the message alert tone off from a remote location Global Setup Setting the Call ScreenSetting Day and Time Setting the Area Code Setting Cidcw Caller ID on Call WaitingSetting the Dial Mode From the handset Using Your PhoneDE-REGISTER the Handset Making a CallReceiving a Call From the Handset SpeakerphoneHanging UP Switching to the Handset Speakerphone During a CallCall Waiting Placing a Call on HoldStoring a Redial Record Deleting a Redial RecordDo not Disturb DND Adjusting the Handset Earpiece and Speaker VolumePrivacy Mode Tone Dialing Switch OverMute Microphone Travelling OUT-OF-RANGEConferencing with one outside line Joining a Conference CallConferencing with 2 outside lines ConferencingFind Handset Flash and Call WaitingStoring Phone Numbers NAMES, Distinctive Rings Speed Dial PhonebookSpeed Dial appears. Press Steps for Entering Names and Special CharactersIf you make a mistake while entering a name Viewing the PhonebookSpeed Dialing Making Calls Using the PhonebookTo finish the viewing operation, press To hang up press ENDEditing the Stored Data Editing or Erasing a DataDeleting the Stored Data Copying Phonebook LocationsTesting Stored Emergency Numbers Caller ID and Cidcw Caller ID on Call Waiting Caller IDViewing the Caller ID List Deleting Information from the Caller ID List Using the Caller ID Message ListDeleting all Caller ID names/ numbers Calling a party from the Caller ID listLong Distance calls and Area Code Setting/Cancellation Viewing the Caller ID List onStoring Caller ID messages in the Phonebook Call Waiting Deluxe Features Expanding Your Phone Dual Handset ExpandabilityRegister the Handset to the Base Using the Directlink Mode INTERCOM/CALL Transfer FeatureDirectLink call Call Transfer Feature IntercomFrom handset to handset Expanding Your Phone Integrated Answering Device FeaturesSetting UP Your Answering System Ô Setting your outgoing message GreetingPre-recorded message Recording a personal outgoing message GreetingAdjusting the Speaker Volume Level Choosing between the two outgoing messagesDeleting an outgoing message Setting the Time Answering System SettingsLED stops flashing when all new messages are played back REPEAT/SELECT until you hear the correct hour settingSetting the ring time Setting a PIN codePress CLOCK/MENU three times Selecting the message record timeAnnounce only feature Setting the message alertPress SET Confirmation tone sounds, the system Selecting the language Screening a call Setting the call screenFrom the base To screen an incoming call, do the steps as followsTo cancel the call screen, press END Using Your Answering SystemPlaying your messages From the handsetRepeating a message Skipping a message Deleting a messageTo maintain maximum record time, delete the old messages. Ô Voice memo Recording a conversationSystem returns to standby Remote Operation Remote access away from homeFunction Remote access with the handset ∅/4 Deleting a Message Stop Operation Ô Remote Key FunctionSymptom Suggestion TroubleshootingKeep the handset away from microwave ovens Care Service and RepairPage Memo Fort Worth, Texas RadioShack Corporation