Radio Shack 43-3704 owner manual Flash and Call Waiting, Find Handset

Page 37

4.To disconnect a single caller, press the corresponding soft key (LINE1 or LINE2) to place the caller you wish to keep speaking to on hold and then press the END soft key to hang up the other caller. For example, to hang up Line 2 but leave Line 1 connected:

•Press the LINE2 soft key to put Line 1 on hold.

•Press the END soft key to hang up Line2.

•Press the LINE1 soft key to take Line 1 off hold and continue the conversation.

To hang up both lines, press END.

FLASH AND CALL WAITING

If you have Call Waiting service and a call waiting tone sounds while you are on a call, press TALK/FLASH to accept the waiting call. There is a short pause, and then you will hear the new caller. To return to the original caller, press TALK/FLASH again.

FIND HANDSET

To locate the handset, press PAGE on the base when the phone is in standby mode. The handset beeps for 60 seconds (if you have two handsets, both handsets beep), and Paging appears on the handset display. To cancel paging, press any key on the handset or PAGE on the base. Ô

Ô NOTE Ô

If the battery pack is completely drained, the handset will not beep.

Using Your Phone

37

Image 37

Contents 43-3704 Contents Introduction FCC Statement InformationSurge Protection Important Safety Instructions Important Caller ID Information Read this Before InstallationSelecting a Location InstallationOn a Wall Plate or Wall On a Desk TopBase downward to secure it CONNECTING/CHARGING the Battery Pack Recharging the Battery PackInstallation Using a Headset Installing a BeltclipTo attach the beltclip To remove the beltclipDisplay and Icons Example of the standby mode displayAnimation Displays Soft KEY Function Talk modeMain Menu Options Default SettingsDirectLink Mode Setting Menu OptionsUsing the Interface Using DirectLink ModeUsing Room Monitor Handset SetupRoom Monitor Confirmation tone, and DirectLinkPress the OK soft key. You will hear a confirmation tone Selecting a Ringer VolumeSelecting a Ringer Tone Distinctive Ringer Setup Setting the Anykey Answer Setting the AutoTalkSetting the True Banner Selecting a Language Setting the Key Touch ToneSetting Room Monitor Setting the Animation ScreenSetting a PIN Code Answering System SetupSetting the Ring Time Setting the Record Time Turning the message alert tone off by pressing any key Setting the Language of your Answering SystemTurning the message alert tone off from a remote location Setting the Call Screen Global SetupSetting Day and Time Setting the Area Code Setting Cidcw Caller ID on Call WaitingSetting the Dial Mode From the handset Using Your PhoneDE-REGISTER the Handset Making a CallReceiving a Call From the Handset SpeakerphoneHanging UP Switching to the Handset Speakerphone During a CallCall Waiting Placing a Call on HoldStoring a Redial Record Deleting a Redial RecordDo not Disturb DND Adjusting the Handset Earpiece and Speaker VolumePrivacy Mode Tone Dialing Switch OverMute Microphone Travelling OUT-OF-RANGEConferencing with one outside line Joining a Conference CallConferencing with 2 outside lines ConferencingFind Handset Flash and Call WaitingStoring Phone Numbers NAMES, Distinctive Rings Speed Dial PhonebookSpeed Dial appears. Press Steps for Entering Names and Special CharactersIf you make a mistake while entering a name Viewing the PhonebookSpeed Dialing Making Calls Using the PhonebookTo finish the viewing operation, press To hang up press ENDEditing the Stored Data Editing or Erasing a DataDeleting the Stored Data Copying Phonebook LocationsTesting Stored Emergency Numbers Caller ID and Cidcw Caller ID on Call Waiting Caller IDViewing the Caller ID List Deleting Information from the Caller ID List Using the Caller ID Message ListDeleting all Caller ID names/ numbers Calling a party from the Caller ID listViewing the Caller ID List on Long Distance calls and Area Code Setting/CancellationStoring Caller ID messages in the Phonebook Call Waiting Deluxe Features Dual Handset Expandability Expanding Your PhoneRegister the Handset to the Base INTERCOM/CALL Transfer Feature Using the Directlink ModeDirectLink call Intercom Call Transfer FeatureFrom handset to handset Expanding Your Phone Integrated Answering Device FeaturesSetting UP Your Answering System Ô Setting your outgoing message GreetingPre-recorded message Recording a personal outgoing message GreetingChoosing between the two outgoing messages Adjusting the Speaker Volume LevelDeleting an outgoing message Setting the Time Answering System SettingsLED stops flashing when all new messages are played back REPEAT/SELECT until you hear the correct hour settingSetting the ring time Setting a PIN codePress CLOCK/MENU three times Selecting the message record timeSetting the message alert Announce only featurePress SET Confirmation tone sounds, the system Selecting the language Screening a call Setting the call screenFrom the base To screen an incoming call, do the steps as followsTo cancel the call screen, press END Using Your Answering SystemPlaying your messages From the handsetRepeating a message Deleting a message Skipping a messageTo maintain maximum record time, delete the old messages. Ô Recording a conversation Voice memoSystem returns to standby Remote Operation Remote access away from homeFunction Remote access with the handset ∅/4 Deleting a Message Stop Operation Ô Remote Key FunctionSymptom Suggestion TroubleshootingKeep the handset away from microwave ovens Care Service and RepairPage Memo Fort Worth, Texas RadioShack Corporation