Radio Shack 43-3704 Adjusting the Handset Earpiece and Speaker Volume, Do not Disturb DND

Page 34

Using Your Phone

Ô NOTE Ô

When you press volume up key (CID/VOL/ ) in the maximum volume level or volume down key (REDIAL/ P/ ) in the lowest volume level, an error tone sounds.

4.Press CID/VOL/ or REDIAL/P/ to choose Store into PB?, and then press the OK soft key.

5.To complete the setting, follow the steps 3-8 in “Storing Phone Numbers, Names, Distinctive Rings, and Speed Dial” on page 38.

ADJUSTING THE HANDSET

EARPIECE AND SPEAKER

VOLUME

You can adjust the handset earpiece and speaker volume separately. Ô

Repeatedly pressing the volume up key or volume down key (labelled as CID/VOL/ or REDIAL/P/ key) during a call will change the earpiece volume of the handset. This setting will remain in effect after the telephone call has ended.

DO NOT DISTURB (DND)

The do not disturb feature (DND) allows you to mute the ringer of the base and any registered handsets at the same time. If you have two handsets, the ringer of both handsets will be muted. To do this, In the standby mode, press and hold DND on the base. The DND LED lights. To cancel ringer mute, press DND again. You can also mute the ringer tone while the phone is ringing by pressing DND on the base.

To mute the ringer tone temporarily for each handset or the base, when the phone is ringing, press MUTE on the handset you want to mute or !PLAY/"STOP on the base.

The ringer tone will return to the previous setting starting with the next incoming call.

34

Image 34

Contents 43-3704 Contents Introduction Information FCC StatementSurge Protection Important Safety Instructions Read this Before Installation Important Caller ID InformationInstallation Selecting a LocationOn a Desk Top On a Wall Plate or WallBase downward to secure it Recharging the Battery Pack CONNECTING/CHARGING the Battery PackInstallation To attach the beltclip Installing a BeltclipUsing a Headset To remove the beltclipDisplay and Icons Example of the standby mode displayAnimation Displays Talk mode Soft KEY FunctionDefault Settings Main Menu OptionsUsing the Interface Setting Menu OptionsDirectLink Mode Using DirectLink ModeRoom Monitor Handset SetupUsing Room Monitor Confirmation tone, and DirectLinkPress the OK soft key. You will hear a confirmation tone Selecting a Ringer VolumeSelecting a Ringer Tone Distinctive Ringer Setup Setting the Anykey Answer Setting the AutoTalkSetting the True Banner Setting the Key Touch Tone Selecting a LanguageSetting the Animation Screen Setting Room MonitorSetting a PIN Code Answering System SetupSetting the Ring Time Setting the Record Time Turning the message alert tone off by pressing any key Setting the Language of your Answering SystemTurning the message alert tone off from a remote location Setting the Call Screen Global SetupSetting Day and Time Setting Cidcw Caller ID on Call Waiting Setting the Area CodeSetting the Dial Mode DE-REGISTER the Handset Using Your PhoneFrom the handset Making a CallFrom the Handset Speakerphone Receiving a CallCall Waiting Switching to the Handset Speakerphone During a CallHanging UP Placing a Call on HoldDeleting a Redial Record Storing a Redial RecordAdjusting the Handset Earpiece and Speaker Volume Do not Disturb DNDMute Microphone Tone Dialing Switch OverPrivacy Mode Travelling OUT-OF-RANGEConferencing with 2 outside lines Joining a Conference CallConferencing with one outside line ConferencingFlash and Call Waiting Find HandsetPhonebook Storing Phone Numbers NAMES, Distinctive Rings Speed DialSteps for Entering Names and Special Characters Speed Dial appears. PressViewing the Phonebook If you make a mistake while entering a nameTo finish the viewing operation, press Making Calls Using the PhonebookSpeed Dialing To hang up press ENDEditing or Erasing a Data Editing the Stored DataCopying Phonebook Locations Deleting the Stored DataTesting Stored Emergency Numbers Caller ID Caller ID and Cidcw Caller ID on Call WaitingViewing the Caller ID List Deleting all Caller ID names/ numbers Using the Caller ID Message ListDeleting Information from the Caller ID List Calling a party from the Caller ID listViewing the Caller ID List on Long Distance calls and Area Code Setting/CancellationStoring Caller ID messages in the Phonebook Call Waiting Deluxe Features Dual Handset Expandability Expanding Your PhoneRegister the Handset to the Base INTERCOM/CALL Transfer Feature Using the Directlink ModeDirectLink call Intercom Call Transfer FeatureFrom handset to handset Expanding Your Phone Features Integrated Answering DevicePre-recorded message Setting your outgoing message GreetingSetting UP Your Answering System Ô Recording a personal outgoing message GreetingChoosing between the two outgoing messages Adjusting the Speaker Volume LevelDeleting an outgoing message LED stops flashing when all new messages are played back Answering System SettingsSetting the Time REPEAT/SELECT until you hear the correct hour settingSetting a PIN code Setting the ring timeSelecting the message record time Press CLOCK/MENU three timesSetting the message alert Announce only featurePress SET Confirmation tone sounds, the system Selecting the language From the base Setting the call screenScreening a call To screen an incoming call, do the steps as followsPlaying your messages Using Your Answering SystemTo cancel the call screen, press END From the handsetRepeating a message Deleting a message Skipping a messageTo maintain maximum record time, delete the old messages. Ô Recording a conversation Voice memoSystem returns to standby Remote access away from home Remote OperationFunction Remote access with the handset Remote Key Function ∅/4 Deleting a Message Stop Operation ÔTroubleshooting Symptom SuggestionKeep the handset away from microwave ovens Service and Repair CarePage Memo RadioShack Corporation Fort Worth, Texas