Radio Shack 43-3704 owner manual On a Desk Top, On a Wall Plate or Wall

Page 9

Your telephone connects directly to a modular telephone line jack. If your telephone wiring does not have a modular jack, you can update the wiring yourself using jacks and adapters (available at your local RadioShack store), or have the telephone company update the wiring for you. Ô

On a Desk Top

1.Plug one end of the supplied long modular cord into the TEL LINE 1/2 jack on the back of the base.

For 2 line subscriptions,

•If the two phone lines are in one modular jack, connect using TEL LINE 1/2 jack.

•If the two phone lines are on two separate modular jacks, connect using both TEL LINE 1/2 and TEL LINE 2 jacks.

2.Plug the modular cord’s other end into a modular phone line jack.

3.Insert the supplied AC adapter’s barrel plug into the DC IN 9V jack on the back of the base. !

4.Route the adapter’s cord through the strain relief slot on the base, then plug the adapter into a standard AC outlet.

On a Wall Plate or Wall

To mount the phone directly on a wall, you need two screws (not supplied) with heads that fit into the keyhole slots on the base.

Drill two holes 315/16 inches apart. Thread a screw into each hole, letting the heads extend about 1/8 inch.

Ô NOTE Ô

The USOC number of the jack to be installed is RJ11C (or RJ11W for a wall plate jack).

! CAUTION !

You must use

!a Class 2 power source

that supplies 9V DC and delivers at least 400 mA. Its center tip must be set to positive and its plug must fit the phone’s DC IN 9V jack. The supplied adapter meets these specifications. Using an adapter that does not meet these specifications could damage the phone or the adapter.

Installation

9

Image 9

Contents 43-3704 Contents Introduction FCC Statement InformationSurge Protection Important Safety Instructions Important Caller ID Information Read this Before InstallationSelecting a Location InstallationOn a Wall Plate or Wall On a Desk TopBase downward to secure it CONNECTING/CHARGING the Battery Pack Recharging the Battery PackInstallation Using a Headset Installing a BeltclipTo attach the beltclip To remove the beltclipExample of the standby mode display Display and IconsAnimation Displays Soft KEY Function Talk modeMain Menu Options Default SettingsDirectLink Mode Setting Menu OptionsUsing the Interface Using DirectLink ModeUsing Room Monitor Handset SetupRoom Monitor Confirmation tone, and DirectLinkSelecting a Ringer Volume Press the OK soft key. You will hear a confirmation toneSelecting a Ringer Tone Distinctive Ringer Setup Setting the AutoTalk Setting the Anykey AnswerSetting the True Banner Selecting a Language Setting the Key Touch ToneSetting Room Monitor Setting the Animation ScreenAnswering System Setup Setting a PIN CodeSetting the Ring Time Setting the Record Time Setting the Language of your Answering System Turning the message alert tone off by pressing any keyTurning the message alert tone off from a remote location Global Setup Setting the Call ScreenSetting Day and Time Setting the Area Code Setting Cidcw Caller ID on Call WaitingSetting the Dial Mode From the handset Using Your PhoneDE-REGISTER the Handset Making a CallReceiving a Call From the Handset SpeakerphoneHanging UP Switching to the Handset Speakerphone During a CallCall Waiting Placing a Call on HoldStoring a Redial Record Deleting a Redial RecordDo not Disturb DND Adjusting the Handset Earpiece and Speaker VolumePrivacy Mode Tone Dialing Switch OverMute Microphone Travelling OUT-OF-RANGEConferencing with one outside line Joining a Conference CallConferencing with 2 outside lines ConferencingFind Handset Flash and Call WaitingStoring Phone Numbers NAMES, Distinctive Rings Speed Dial PhonebookSpeed Dial appears. Press Steps for Entering Names and Special CharactersIf you make a mistake while entering a name Viewing the PhonebookSpeed Dialing Making Calls Using the PhonebookTo finish the viewing operation, press To hang up press ENDEditing the Stored Data Editing or Erasing a DataDeleting the Stored Data Copying Phonebook LocationsTesting Stored Emergency Numbers Caller ID and Cidcw Caller ID on Call Waiting Caller IDViewing the Caller ID List Deleting Information from the Caller ID List Using the Caller ID Message ListDeleting all Caller ID names/ numbers Calling a party from the Caller ID listLong Distance calls and Area Code Setting/Cancellation Viewing the Caller ID List onStoring Caller ID messages in the Phonebook Call Waiting Deluxe Features Expanding Your Phone Dual Handset ExpandabilityRegister the Handset to the Base Using the Directlink Mode INTERCOM/CALL Transfer FeatureDirectLink call Call Transfer Feature IntercomFrom handset to handset Expanding Your Phone Integrated Answering Device FeaturesSetting UP Your Answering System Ô Setting your outgoing message GreetingPre-recorded message Recording a personal outgoing message GreetingAdjusting the Speaker Volume Level Choosing between the two outgoing messagesDeleting an outgoing message Setting the Time Answering System SettingsLED stops flashing when all new messages are played back REPEAT/SELECT until you hear the correct hour settingSetting the ring time Setting a PIN codePress CLOCK/MENU three times Selecting the message record timeAnnounce only feature Setting the message alertPress SET Confirmation tone sounds, the system Selecting the language Screening a call Setting the call screenFrom the base To screen an incoming call, do the steps as followsTo cancel the call screen, press END Using Your Answering SystemPlaying your messages From the handsetRepeating a message Skipping a message Deleting a messageTo maintain maximum record time, delete the old messages. Ô Voice memo Recording a conversationSystem returns to standby Remote Operation Remote access away from homeFunction Remote access with the handset ∅/4 Deleting a Message Stop Operation Ô Remote Key FunctionSymptom Suggestion TroubleshootingKeep the handset away from microwave ovens Care Service and RepairPage Memo Fort Worth, Texas RadioShack Corporation