Radio Shack 43-3704 To attach the beltclip, To remove the beltclip, Installing a Beltclip

Page 13

INSTALLING A BELTCLIP

To attach the beltclip

Insert the beltclip into the holes on each side of the handset. Press down until it clicks.

To remove the beltclip

Pull either side of the beltclip to release the tabs from the holes.

USING A HEADSET

You can make or answer calls with hands- free convenience using an optional headset that has a 3/32-inch (2.5-mm) plug.

RadioShack has a variety of headsets available.

To connect the headset, gently flip open the rubber headset jack cover on the side of the handset, then insert the headset’s plug into the jack. Ô

Connecting a headset disconnects the handset’s earpiece and microphone.

CID/VOL/ or REDIAL/P/ on the handset also controls the headset’s volume.

With a headset connected, you can make or answer calls as usual using the keys on the handset.

When you finish using the headset, disconnect it from the handset and close the rubber cover to protect the jack.

Ô NOTES Ô

•If you place the handset on the base to recharge it while the headset is connected, be sure the handset seats properly.

•You can use a handset holder (available from your local RadioShack store) to hang the handset on your belt for greater convenience when using a headset.

Installation

13

Image 13

Contents 43-3704 Contents Introduction FCC Statement InformationSurge Protection Important Safety Instructions Important Caller ID Information Read this Before InstallationSelecting a Location InstallationOn a Wall Plate or Wall On a Desk TopBase downward to secure it CONNECTING/CHARGING the Battery Pack Recharging the Battery PackInstallation Using a Headset Installing a BeltclipTo attach the beltclip To remove the beltclipDisplay and Icons Example of the standby mode displayAnimation Displays Soft KEY Function Talk modeMain Menu Options Default SettingsDirectLink Mode Setting Menu OptionsUsing the Interface Using DirectLink ModeUsing Room Monitor Handset SetupRoom Monitor Confirmation tone, and DirectLinkPress the OK soft key. You will hear a confirmation tone Selecting a Ringer VolumeSelecting a Ringer Tone Distinctive Ringer Setup Setting the Anykey Answer Setting the AutoTalkSetting the True Banner Selecting a Language Setting the Key Touch ToneSetting Room Monitor Setting the Animation ScreenSetting a PIN Code Answering System SetupSetting the Ring Time Setting the Record Time Turning the message alert tone off by pressing any key Setting the Language of your Answering SystemTurning the message alert tone off from a remote location Setting the Call Screen Global SetupSetting Day and Time Setting the Area Code Setting Cidcw Caller ID on Call WaitingSetting the Dial Mode From the handset Using Your PhoneDE-REGISTER the Handset Making a CallReceiving a Call From the Handset SpeakerphoneHanging UP Switching to the Handset Speakerphone During a CallCall Waiting Placing a Call on HoldStoring a Redial Record Deleting a Redial RecordDo not Disturb DND Adjusting the Handset Earpiece and Speaker VolumePrivacy Mode Tone Dialing Switch OverMute Microphone Travelling OUT-OF-RANGEConferencing with one outside line Joining a Conference CallConferencing with 2 outside lines ConferencingFind Handset Flash and Call WaitingStoring Phone Numbers NAMES, Distinctive Rings Speed Dial PhonebookSpeed Dial appears. Press Steps for Entering Names and Special CharactersIf you make a mistake while entering a name Viewing the PhonebookSpeed Dialing Making Calls Using the PhonebookTo finish the viewing operation, press To hang up press ENDEditing the Stored Data Editing or Erasing a DataDeleting the Stored Data Copying Phonebook LocationsTesting Stored Emergency Numbers Caller ID and Cidcw Caller ID on Call Waiting Caller IDViewing the Caller ID List Deleting Information from the Caller ID List Using the Caller ID Message ListDeleting all Caller ID names/ numbers Calling a party from the Caller ID listViewing the Caller ID List on Long Distance calls and Area Code Setting/CancellationStoring Caller ID messages in the Phonebook Call Waiting Deluxe Features Dual Handset Expandability Expanding Your PhoneRegister the Handset to the Base INTERCOM/CALL Transfer Feature Using the Directlink ModeDirectLink call Intercom Call Transfer FeatureFrom handset to handset Expanding Your Phone Integrated Answering Device FeaturesSetting UP Your Answering System Ô Setting your outgoing message GreetingPre-recorded message Recording a personal outgoing message GreetingChoosing between the two outgoing messages Adjusting the Speaker Volume LevelDeleting an outgoing message Setting the Time Answering System SettingsLED stops flashing when all new messages are played back REPEAT/SELECT until you hear the correct hour settingSetting the ring time Setting a PIN codePress CLOCK/MENU three times Selecting the message record timeSetting the message alert Announce only featurePress SET Confirmation tone sounds, the system Selecting the language Screening a call Setting the call screenFrom the base To screen an incoming call, do the steps as followsTo cancel the call screen, press END Using Your Answering SystemPlaying your messages From the handsetRepeating a message Deleting a message Skipping a messageTo maintain maximum record time, delete the old messages. Ô Recording a conversation Voice memoSystem returns to standby Remote Operation Remote access away from homeFunction Remote access with the handset ∅/4 Deleting a Message Stop Operation Ô Remote Key FunctionSymptom Suggestion TroubleshootingKeep the handset away from microwave ovens Care Service and RepairPage Memo Fort Worth, Texas RadioShack Corporation