Eaton Electrical SC200 manual APS6-05X Rack-Mounted Versions

Page 11

Data Power Solutions Product Range

APS6-05X (Rack-Mounted Versions)

"

#

Three 2-pole Battery Circuit Breakers (APS6-059 only)

Load Circuit Breakers – any combination of 6 A or 25 A rated circuit breakers up to a maximum of eight, depending on customer requirements

$

%

Up to six Access Power Rectifiers, numbered 1 to 6 from left to right (see page 1-6)

SM45 Display Module with keypad and LED indicators (see Chapter 5)

!SM45 Supervisory Module (see page 1-7)

&16 DC Load Terminal Blocks (2 per DC Outlet)

3Six Battery Terminal Blocks (APS6-059 only)

4Two Battery Temperature Sensor Terminal Blocks (APS6-059 only)

5Three Battery Cable Clamps (APS6-059 only)

'

(

)

Six fused AC Power Sockets (one per rectifier) and labeled K1 to K6. K1 powers Rectifier 1, etc.

DC Output Cover (remove to access DC output terminations)

Cable Support Bracket

Copyright © 2005-2006 Eaton Corporation. All Rights Reserved.

1-5

IPN 997-00012-41D December 2006

 

Image 11
Contents Data Power Solutions Installation Guide Copyright 2005-2006 Eaton Corporation All Rights Reserved About This Guide About This Guide For Further Information and Technical AssistanceTable of Contents Chapter Operations Table of ContentsTopic General DescriptionOverview General Description Data Power Solutions Product RangeAPS3-05X Rack-Mounted Versions Data Power Solutions Product RangeAPS3-06X Desktop Versions APS6-05X Rack-Mounted Versions Access Power Rectifiers SM45 Supervisory Module SM45 Supervisory ModuleLow Voltage Disconnect if applicable Pre-Installation AC Inputs Pre-InstallationBatteries if applicable DC Outputs Servicing Inspecting the Equipment and Reporting Damage Installation Location and Environment Mounting the Power SystemInstallation Rack Installation rack-mounted versions onlyDC Installation Practices DC Installation PracticesConnecting the DC Load Cables APS3-05X and APS6-05X Rack-Mounted Versions Installation DC Load Cable SpecificationsFit load cable clamps Connecting the DC Load CablesFit cables and sleeves Battery Location Installing the External Batteries if applicableInstalling the External Batteries if applicable Battery SizingBefore You Start Connecting the Battery Cables if applicableBattery Fault Protection Battery Cable SpecificationsPrepare cable clamp Connecting the Battery Cables if applicableConnecting the Battery Temperature Sensor Cable Repeat for other battery cables if requiredMounting the Battery Temperature Sensor AC Supply Requirements Connecting the Power System to the AC SupplyAC Installation Commissioning Commissioning Inserting the Access Power RectifiersChecklist Pre-Power-Up CheckPre-Power-Up Check Configuring the Power System for Operation Applying AC PowerBefore you start, you need Configuring the Power System for OperationLVD Hotlink Click to …Page Applying DC Power to the Load SM45 Operations SM45 Operations About the SM45 Front PanelTo change the display contrast To disable the audible indicator when an alarm is activeAbout the SM45 Front Panel About Display Modes To enter a display modeTo exit a display mode To scroll within a display modeTo view system values Viewing System Values Main Display ModeViewing System Values Main Display Mode To view and clear alarms Viewing Alarms and System Status Messages Status View ModeRules for displaying alarms and system status Important note about Rect Comms Lost alarmTo view and edit a configuration parameter Viewing and Editing Configuration ParametersViewing and Editing Configuration Parameters SM45 Operations Communications Direct Connection Ethernet Communications OptionsCommunications Properties Direct Connection Ethernet DCTools SetupSM45 Ethernet Setup DCTools SetupParameter Configuration Guidelines Setting Up Snmp TrapsTo enter the sysObjectID of a power system using DCTools Entering the sysObjectID of a Power SystemEntering the sysObjectID of a Power System Synchronizing the SM45 Real-time Clock To synchronize the SM45 real-time clock using DCToolsMaintenance Problem Possible Cause/s Required Action TroubleshootingMaintenance Troubleshooting LED Config Error Removing a Rectifier Replacing a RectifierReplacing a Rectifier Pull out the rectifierInserting a Rectifier To check and replace AC input fuses Replacing AC Input FusesReplacing AC Input Fuses Replacing the SM45 Real-time Clock Battery Glossary of Alarms Rectifier Fail Sensor Fail System Overload Glossary of AlarmsMultiple Rectifier Fail Partial AC Fail Rectifier Comms LostControl Function Glossary Battery Current Limit BCLControl Function Glossary Low Volts DisconnectEnvironment SpecificationsSystem AC Input System DC OutputAPR48 Rectifiers SpecificationsDimensions H, W, D WeightEquipment Incident Report SG/03 ISS04 United States of America Worldwide SupportPage Page Page SM45 Front Panel Menu Structure Configuration Mode Edit Mode