Eaton Electrical SC200 manual About Display Modes, To enter a display mode, To exit a display mode

Page 44

SM45 Operations

About Display Modes

The SM45 front panel menu structure consists of four display modes:

Main Display Mode – for viewing system values

Status View Mode – for viewing system statuses as well as viewing and clearing alarms

Configuration Mode – for viewing settings of configurable parameters

Edit Mode – for editing the configurable parameters in Configuration Mode

For quick and easy reference, graphical representations of the menu structure are printed on the inside front and back covers.

Changing Display Modes

To enter a display mode

From Main Display Mode, press the

From Main Display Mode, press the

key to enter Status View Mode and Alarm Mode. key to enter Configuration Mode and Edit Mode.

To exit a display mode

Press the key to return from any mode to Main Display Mode.

Scrolling within a Display Mode

To scroll within a display mode

Press the key to scroll up within a display mode.

Press the key to scroll down within a display mode.

To scroll through a display mode faster, hold down the or key.

Using Edit Mode

For details about viewing and editing configuration parameters, see page 2-7.

5-4

Copyright © 2005-2006 Eaton Corporation. All Rights Reserved.

IPN 997-00012-41D December 2006

 

Image 44
Contents Data Power Solutions Installation Guide Copyright 2005-2006 Eaton Corporation All Rights Reserved About This Guide For Further Information and Technical Assistance About This GuideTable of Contents Table of Contents Chapter OperationsTopic General DescriptionOverview Data Power Solutions Product Range General DescriptionData Power Solutions Product Range APS3-05X Rack-Mounted VersionsAPS3-06X Desktop Versions APS6-05X Rack-Mounted Versions Access Power Rectifiers SM45 Supervisory Module SM45 Supervisory ModuleLow Voltage Disconnect if applicable Pre-Installation Pre-Installation AC InputsBatteries if applicable DC Outputs Servicing Inspecting the Equipment and Reporting Damage Installation Mounting the Power System InstallationRack Installation rack-mounted versions only Location and EnvironmentDC Installation Practices DC Installation PracticesConnecting the DC Load Cables Installation DC Load Cable Specifications APS3-05X and APS6-05X Rack-Mounted VersionsConnecting the DC Load Cables Fit load cable clampsFit cables and sleeves Installing the External Batteries if applicable Installing the External Batteries if applicableBattery Sizing Battery LocationConnecting the Battery Cables if applicable Battery Fault ProtectionBattery Cable Specifications Before You StartConnecting the Battery Cables if applicable Prepare cable clampRepeat for other battery cables if required Connecting the Battery Temperature Sensor CableMounting the Battery Temperature Sensor AC Supply Requirements Connecting the Power System to the AC SupplyAC Installation Commissioning Inserting the Access Power Rectifiers CommissioningChecklist Pre-Power-Up CheckPre-Power-Up Check Applying AC Power Configuring the Power System for OperationConfiguring the Power System for Operation Before you start, you needHotlink Click to … LVDPage Applying DC Power to the Load SM45 Operations About the SM45 Front Panel SM45 OperationsTo change the display contrast To disable the audible indicator when an alarm is activeAbout the SM45 Front Panel To enter a display mode To exit a display modeTo scroll within a display mode About Display ModesTo view system values Viewing System Values Main Display ModeViewing System Values Main Display Mode Viewing Alarms and System Status Messages Status View Mode Rules for displaying alarms and system statusImportant note about Rect Comms Lost alarm To view and clear alarmsTo view and edit a configuration parameter Viewing and Editing Configuration ParametersViewing and Editing Configuration Parameters SM45 Operations Communications Direct Connection Ethernet Communications OptionsCommunications DCTools Setup SM45 Ethernet SetupDCTools Setup Properties Direct Connection EthernetSetting Up Snmp Traps Parameter Configuration GuidelinesTo enter the sysObjectID of a power system using DCTools Entering the sysObjectID of a Power SystemEntering the sysObjectID of a Power System To synchronize the SM45 real-time clock using DCTools Synchronizing the SM45 Real-time ClockMaintenance Problem Possible Cause/s Required Action TroubleshootingMaintenance Troubleshooting LED Config Error Replacing a Rectifier Removing a RectifierPull out the rectifier Replacing a RectifierInserting a Rectifier To check and replace AC input fuses Replacing AC Input FusesReplacing AC Input Fuses Replacing the SM45 Real-time Clock Battery Glossary of Alarms Glossary of Alarms Multiple Rectifier FailPartial AC Fail Rectifier Comms Lost Rectifier Fail Sensor Fail System OverloadBattery Current Limit BCL Control Function GlossaryLow Volts Disconnect Control Function GlossarySpecifications System AC InputSystem DC Output EnvironmentSpecifications Dimensions H, W, DWeight APR48 RectifiersEquipment Incident Report SG/03 ISS04 Worldwide Support United States of AmericaPage Page Page SM45 Front Panel Menu Structure Configuration Mode Edit Mode