EnGenius Technologies 1X instruction manual Charger Features, Handset and Charger Installation

Page 10

Charger Features

1.DC In

Connects to Charger AC Adaptor.

2.Handset Charging Slot

a.Charge handset battery when handset is placed in cradle.

b.Refer to the handset LCD for charging status

(1)Charging: LCD screen showed “Charging”

(2)Fully Charged: battery status bar stands still and the LCD screen would display “Fully Charged”

(3)Charge Fail: Should there be any error occurred during charging mode, the LCD screen would display “Charge Fail”

3.Spare Battery Charging Slot

a.Charge spare battery when battery is placed in slot.

b.LED as the spare battery charging indicator

(1)Slot is empty and the power is on: LED is Green light

(2)Charging: LED is Orange light

(3)Fully Charged: LED returns to Green light

4.It is impossible to overcharge the battery using this charger.

Notes:

1.Fully charge battery packs before first use.

2.Both handset and spare batteries can be charged at the same time.

3.Handset will be “power on” automatically when placing on the charging slot.

4.However, if you run drain the battery, it would take around one minute for handset to auto power on.

5.The adaptor for charging station can be used as travel charger as well. However, you can’t turn off the power while you charge the handset via travel charger. A Warning message: “Unplug Travel Charger than OFF the power” will be shown on the LCD display.

Getting Started

Base Station Installation

There are three possible base station setups:

zBase station alone

zBase station plus telephone answering device

zBase station plus standard telephone

For best performance, maintain at least a distance of 1 meter (about 3 feet) between the base station and other electronic devices (e.g., TV, computer, stereo, fax machine, answer machine, cordless phone, etc.)

1.Install base station antenna.

The base station’s antenna port has a reverse-thread connector; to install antenna or cable, turn counter-clockwise.

2.Plug the transformer end of the base station AC/DC adaptor into a standard AC electrical power outlet, plug the other end into the “DC In” jack on the back of the base station.

3.Plug phone cord into the “LINE” Jack

4.A standard telephone or answering machine can be plugged into the adjacent receptacle on the bottom of the base station marked TEL

Handset and Charger Installation

1.Plug the transformer end of the Charger AC/DC adaptor into a standard AC electric power outlet, plug the other end into the “DC In” jack on the back of the Charging Cradle.

2.Install battery pack onto the handset.

3.Install handset antenna.

4.Place handset onto the charger front slot.

5.Fully charge the battery for three hours before use.

6.The phone system is now ready to perform basic functions such as making

~19~

~20~

Page 9 Page 11
Image 10
Page 9 Page 11
Contents DuraFon General Safety Instructions Safety InstructionsProduct Safety Instructions Battery Safety Instructions Regulatory Information DuraFon FCC ID NI3-SN1302 IC 3616A-SN1302Handset Illustration Equipment ChecklistOLQH/& TALK/ Speakerphone Basic Handset FeaturesAdditional Handset Features WAY/INTERCOM~13~ ~14~ Base Illustration Administrator FeaturesIRU Antenna Basic Base Station Features,Q Charger Features Handset and Charger InstallationOperation Modes Menu modeBasic Operations Base Operation ModesPress END key to end the call Making an 2-Way/ Intercom CallIntercom/2-Way from Base to Handset Broadcasting from Base to Handset Intercom/2-Way from Handset to BaseCoverage Broadcasting from Handset to BasePlacing a Call On Hold Adjusting Receiver Earpiece Voice VolumeReceiving a Telephone Call Receiving an Intercom CallDo Not Disturb Silent Ring Battery Recharge and ReplacementEffective only for the current call Key GuardHandset Group Subscription Advanced OperationsHandset Registration Registration of Additional BaseCall Transfer Change System Settings by AdministratorCall Manager Phonebook Operations  LDOIURPGLVSOD\ Call barringText Messaging Programmable PBX OptionsMenu Operations Press 6 to change LCD display contrast Press 0 to program PBX features that you use frequently Technical SpecificationsPress 9 to enable Name tag Press 7 to change the LCD backlightIndex Page Effectuer un appel téléphonique Ajuster le volume de la voix du récepteur écouteurFaire une diffusion 102 Instructions de sécuritéInstructions générales de sécurité Instructions de sécurité du produit Instructions de sécurité pour la batterieInformation sur les règlements Liste de vérification de l’équipement Illustration du combinéCaractéristiques de base du combiné Caractéristiques additionnelles du combiné~59~ ~60~ Caractéristiques de l’administrateur Illustration de la base DUDFWpULVWLTXHVGHEDVHGHODVWDWLRQGHEDVHIllustration du chargeur GXFRPELQpUHFKDQJHHVWHQFKDUJHPHQW DUDFWpULVWLTXHVGXFKDUJHXU HQWHGHFKDUJHPHQWGHODEDWWHULHGHUHFKDQJH YR\DQW/ / HVWXQYR\DQWOXPLQHXYHUWInstallation du combiné et du chargeur Comment démarrerModes d’opération Mode MenuOpérations de base Modes de fonctionnement de base$&RPELQpV jDSSHOVGHFRPELQpV IIHFWXHUXQDSSHOWpOpSKRQLTXHHQVXLWHDSSX\HVXUODWRXFKH7$/. ¶LGHQWLILFDWLRQGXJURXSH’identification ID de la Base 2 est Intercom/Bidirectionnel de la base au combiné« Broadcast » Tous les combinés à l’intérieur de la couvertureRecevoir un appel Intercom Ajuster le volume de la voix du récepteur écouteurRecomposition Recevoir un appel téléphoniqueGarde-touches Ne pas déranger Sonnerie silencieuseMettre un appel en attente DiscrétionOpérations avancées Recharge et remplacement de la batterieEnregistrement du combiné Enregistrement de groupe de combinés Enregistrement d’une base supplémentaireTransfert d’appels Modifier les paramètres du système par administrateur Gestionnaire d’appelsDe la base à deux chiffres pour accéder au mode Vous pouvez ajuster le mode de compositionEntre Tonalité et Impulsion. Le mode par défaut La tonalitéNumero ? Configuration » et une confirmation TerminéOpérations de l’annuaire téléphonique Nom ? Capitale =Interdiction d’appels Messagerie texte Vide EntrantOptions d’autocommutateur privé programmables Code de disposOpérations du menu Appuyez sur 8 pour modifier l’interdiction d’appels Appuyez sur 9 pour permettre le nom abrégéSpécifications techniques ~103~
Top Page Image Contents