Panasonic KX-TG8561FX, KX-TG8551FX Registering a handset to a base unit, Selecting a base unit

Page 40

Programming

Note:

RCalls are disconnected when the handset moves from one radio cell to another.

Registering a handset to a base unit

The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit (for example, is displayed even when the handset is near the base unit), re-register the handset.

1Handset:

(middle soft key) #130

2MbN: Select a base unit number. a R This number is used by the handset as

a reference only.

3Base unit:

Proceed with the operation for your model.

n KX-TG8551 series: page 3 Press and hold MN for about 5 seconds. (No registration tone)

n KX-TG8561 series: page 3 Press and hold MN for about 5 seconds, until the registration tone sounds.

R If all registered handsets start ringing, press MN again to stop, then repeat this step.

R The next step must be completed within 90 seconds.

4Handset:

a Wait until Base PINis displayed. a Enter the base unit PIN

(default: 0000). a

R If you forget your PIN, contact an authorised service centre.

R When the handset has been registered

successfully, is displayed.

Note:

R While registering, Base in registeringis displayed on all registered handsets.

RWhen you purchase an additional handset, refer to the additional handset’s installation manual for registration.

Selecting a base unit

When Autois selected, the handset automatically uses any available base unit it is registered to. When a specific base unit is selected, the handset makes and receives calls using that base unit only. If the handset is out of range of that base unit, no calls can be made.

1 (middle soft key) #137

2MbN: Select the desired base unit number,

or Auto. a

R The handset starts searching for the base unit.

Deregistering a handset

A handset can cancel its own registration to the base unit, or other handsets registered to the same base unit. This allows the handset to end its wireless connection with the system.

1 (middle soft key) #131

R All handsets registered to the base unit are displayed.

2MbN: Select the handset you want to cancel. a

3MbN: Yesa

R A confirmation tone sounds.

R The handset does not beep when cancelling its own registration.

4MN

Cancelling a base unit

A handset can cancel a base unit that it is registered to. This allows the base unit to end its wireless connection with the system.

1 (middle soft key) #139

2MbN: Select the base unit you want to cancel. a

3MbN: Yesa a MN

Note:

RTo register a handset to another base unit or to the same base unit again, see page 40.

40

TG8551_61FX_(en-en)_0427_ver021.40 40

2012/04/27 20:24:47

Image 40
Contents Digital Cordless Answering System Digital Cordless PhoneThank you for purchasing a Panasonic product Table of Contents Accessory information Supplied accessoriesFeature differences Model compositionAdditional/replacement accessories Accessory itemExpanding your phone system Model numberGeneral information For your future referenceDeclaration of Conformity Attach your purchase receipt hereFor your safety Important safety instructions BatteryFor best performance Base unit location/avoiding noiseOther information Routine careFor business users in the European Union Do not use benzine, thinner, or any abrasive powderSpecifications Setting up Battery installationBattery charging ConnectionsIcon Battery level Battery levelOperation Operating time Controls HandsetBase unit Navigator keyDisplay Handset display itemsKX-TG8561 series MeaningHandset soft key icons LineUse Icon ActionScreen saver mode Turning the power on/offInitial settings Display languageOne touch eco mode Display modeDialling mode Programming the display mode beforehandMbN Select the desired setting. a Making calls Making a call using the redial listAnswering calls Useful features during a call Power back-up operation Key lockHandset equalizer Recording a telephone conversationMaking calls during a power failure When only 1 handset is registeredPhonebook Adding entriesCategories Changing category namesFinding and calling from a phonebook entry Scrolling through all entriesSearching by first character Searching by queryCopying phonebook entries Editing entriesErasing entries Chain dialCopying multi entries Copying all entriesTo copy to the personal phonebook MbN Copy All aSpeed dial Programmable settings Display the menu tree and direct command code tableSettings Number of Rings*2 Receive List Send List Create SettingsRinger Volume Handset Rings Auto Recording Time*2 MinuteNight Mode On/Off Ring Delay 30 secMemo Alarm Alarm1-5 Once Time Adjustment *2, *10 Caller IDRinger Setup Ringer Volume Handset Ringer VolumeNight Mode On/Off Night ModeDisplay Setup Wallpaper *11 Wallpaper1 Colour2 Display Mode Multi ItemsLine Setup Dial Mode *2 Pulse 2 Tone Msec # 160 msec Privacy Mode *2, *17Power Failure Auto Language DisplayEnglish Sensitivity LevelAlarm Special programmingČeská rep. = 100 msec. Slovensko = 100 msec OnceNight mode Changing the handset nameSetting call restriction Incoming call barring Caller ID subscribers onlyChanging the base unit PIN Personal Identification Number Storing unwanted callersChanging the unit’s region setting/Resetting the base unit Calendar/ScheduleAdding a new entry Česká rep. = Czech Slovensko = SlovakiaMbN Select the desired alarm tone. a Times Baby monitorViewing entries Editing an entrySetting the baby monitor To monitor with a handsetTo monitor from an outside line Turning off the baby monitorAnswering the baby monitor Registering a unitOperating additional units Cancelling a base unit Registering a handset to a base unitSelecting a base unit Deregistering a handsetSetting the repeater mode Increasing the range of the base unitDo not use more than one repeater at a time Dect repeaterUsing Caller ID service Caller ID featuresCaller list Category ringer toneViewing the caller list and calling back Editing a caller’s phone number before calling backErasing selected caller information Erasing all caller informationUsing SMS Turning SMS on/offStoring SMS message centre numbers Sending a messageReceiving a message Editing/sending a saved messageErasing saved messages Reading a received messageOther settings Answering system Turning the answering system on/offGreeting message Memory capacity including your greeting messageListening to messages using the base unit Listening to messages using the handsetRecording your greeting message Playing back the greeting messageRemote operation Listening to messages from the message listOperating the answering system Calling back Caller ID subscribers onlyAnswering system settings For voice mail service subscribers Middle soft key #211 MbN Select the desired setting. aIf your service provider/telephone company cannot do this Caller’s recording timeVoice mail service Handset locator IntercomTransferring calls, conference calls When the unit displays the character entry screen Character entryCharacter entry modes Alphabet character table ABCGreek character table Extended 1 character tableFollowing are used for both uppercase and lowercase Extended 2 character table Not available for SMSTG855161FXen-en0427ver021.56 2012/04/27 Cause/solution Error messagesDisplay message Troubleshooting Programmable settingsProblem General useBattery recharge Making/answering calls, intercomSMS Short Message Service Caller IDCannot make a call FD is displayed FE is displayedLiquid damage Answering systemE0 is displayed Belt clip To attachIndex FX-2/3 Sales Department Czech SlovakiaRomania PNQX5210ZA TT0412KM0 a