Orion LBI-38888K manual Squelch Adjust, Menu Selection

Page 60

SQUELCH ADJUST

In the conventional mode of operation, the squelch may be re-adjusted in the MENU selection mode or from a front panel key on the keypad that has been pre-programmed by the PC progamming software. A default value of 9 or any user level between 1 and 16 can be selected by the PC programming software. The user can change this setting either of two ways from the front panel keys.

NOTE

A value of 16 requires a strong signal to open squelch, a value of 2 requires a very weak signal to open squelch and a value of 1 is open squelch.

NOTE

When squelch adjust feature is activated, Channel Guard, T99 decode and Scan are disabled. When the squelch adjust feature is exited, Channel Guard, T99 decode and Scan are restored to their previous states.

Menu Selection

1.Press the mkey and then use the RAMP control ,or .to scroll

through the selections until SQUELCH is displayed. Then press m (SELECT) again.

2.The display will show SQLCH=xx, where "xx" is the value between 1 and 16.

3.Use the RAMP control ,or .to scroll through the values. Then

press the m (SELECT) key to save the new value after the display time-out (2 seconds). The displayed value will be selected and saved.

4.If the mor ckey is pressed before the time-out, the menu feature will exit and the squelch level will not be updated. The original value will be restored.

Pre-Programmed Keypad Key

1.Press the pre-programmed key and the display will indicate SQLCH=xx, where "xx" is the value between 1 and 16.

60

Image 60

Contents Orion Product Specification for CE Marked Equipment Table of Contents Table of Contents Safety Information List of the possible hazards are Explosive AtmospheresInterference To Vehicular Electronic Systems Dynamite Blasting CapsIntroduction User InterfaceOrion Mobile Radio System Model Front Panel Power ON-OFF Volume Knob ControlsSYSTEM/GROUP Channel Knob Indicators Ramp ControlScan ON/OFF Scan ADD/DELETEKeypad Orion System Model KeypadStandard Keycap Configuration Optional Keycap ConfigurationKey Descriptions Entry see Selection Mode Rules Primary Functions Quick Access ALMDisplay Radio Status IconsMessages Message Name DescriptionTX Data WHC=1 FIX List Spkr on Autokey Trunked Mode only Call Queued Trunked Mode onlySystem Busy Trunked Mode only Alert TonesCall Denied Trunked Mode only Carrier Control TimerDual Control Switching OperationSelection Mode Rules Turning on the RadioDirect Access U T HMenu N U K L G H T Press SEL Menu Item Information Feature Display Parameter Comment Settings SYS Scan Feature Encryption Display Feature Encryption Data StreamSerial Number ROM 12 Hex Digits Example Features Enabled Number FieldsBIT Fields Possible Features SYSTEM/GROUP/CHANNEL Selection System SelectionGroup And Channel Selection Trunked Mode Operation Receiving a CallSending a Call Conventional Failsoft Emergency OperationReceiving An Emergency Call System Scan Operation Declaring An Emergency CallWide Area System Scan ProSoundTM ProScanTMWhen Wide Area System Scan Is Enabled When ProSound/ProScan Is EnabledPriority System Scan Menu SelectionGroup Scan Operation Adding Groups To a Scan List Deleting Groups From a Scan ListNuisance Delete Turning Scan onPriority Group Scanning Individual Calls Turning Scan OFFReceiving and Responding To An Individual Call Page Scat Operation Sending An Individual CallReceiving a Telephone Interconnect Call Trunked Mode Only Sending a Telephone Interconnect Call Trunked Mode OnlyTelephone Interconnect Calls Dtmf Overdial/Conventional Mode Telephone Interconnect Programmable Entries Mobile Data DisplaysData OFF Operation Data On OperationScan Lockout Mode Exiting Data CallsData Lockout Mode STATUS/MESSAGE OperationStatus Operation Edacs Conventional P1 Scan Message OperationConventional Mode Operation Dynamic Regroup OperationEmergency Operation Receiving a Call Using 5-Tone Signalling for Emergency Declaration Tone Encode TransmissionScanning Conventional Channels Adding Channels To a Scan List Deleting Channels From a Scan ListTurning Scan on Turning Scan OFFSquelch Adjust Noise Blanker Operation Type 99 Decode Conventional OnlyMenu Selection Direct Mode Operation Conventional System Only Trunked or Conventional Mode Operation SIREN/LIGHT OperationVoice Modes AEGIS/ProVoice Digital Mode YesClear Modes Error Messages ERR=xxxxPage Transferring Keys Into The Radio Displaying The Currently Used Cryptographic Key NumberKey Zero Private Operation Receiving An Encrypted CallTransmitting An Encrypted Call Scanned Group Calls Conventional Operation Outside AddressSwitching Control Control Switching ModesDual Control Operation Channel GuardSlaved Mode Operation Independent Mode OperationSiren And Light Control Multiple Radio Operation Dual Control AudioChanging Selected Radio Shared Control Unit Display ModesFirst Come First Serve Display Audio ModesAudio Summed Audio First Come First ServeMacro KEY Operation Page Keypad Remapping Operating Rules and Regulations Glossary Group Or Subfleet Group Scan Individual Call Queueing SiteController SystemTalk-around TelephoneInter ConnectOperators Radio Setup Radio Type Frequency Band Operators Name Emergency GroupWarranty Emergency Numbers Operating Tips