Orion LBI-38888K manual System Scan Operation, Declaring An Emergency Call, Wide Area System Scan

Page 36

Declaring An Emergency Call

To send an emergency call to the selected system and group (or on an optionally pre-programmed emergency group), proceed as follows:

1.Press and hold the red E button for approximately one second (this time is programmable and therefore could be longer or shorter; check with the system administrator). The radio will transmit an emergency call request with the radio ID until an emergency channel assignment is received.

2.When the working channel assignment is received, the radio sounds a single beep (Autokey alert tone) indicating it is ready for voice transmission. *TXEMER* flashes on line two in the display until the emergency is cleared.

3.Press PTT and speak into the microphone in a normal voice.

4.Release PTT when the transmission is complete and listen for a reply.

5.The emergency can be cleared by pressing and holding the cbutton followed by pressing the Ebutton then releasing both buttons.

SYSTEM SCAN OPERATION

The radio can be programmed with the following System Scan features. These features are automatically enabled upon radio power up. A key or menu option is also defined to allow the System Scan features to be toggled during radio operation. This is covered in the Menu Selection and Pre- Programmed Keypad Key sections. The System Scan state will be maintained through system changes but will default to ON at power up.

Wide Area System Scan

The ORION radio may be programmed for wide area system scan operation for multi-site applications. Upon the loss of the currently selected system's control channel, radios may be programmed to automatically scan the control channels of other systems. If a new control channel is found, the radio will switch to the new system and sound an alert tone.

36

Image 36

Contents Orion Product Specification for CE Marked Equipment Table of Contents Table of Contents Safety Information List of the possible hazards are Explosive AtmospheresInterference To Vehicular Electronic Systems Dynamite Blasting CapsIntroduction User InterfaceOrion Mobile Radio System Model Front Panel Power ON-OFF Volume Knob ControlsSYSTEM/GROUP Channel Knob Indicators Ramp ControlScan ON/OFF Scan ADD/DELETEKeypad Orion System Model KeypadStandard Keycap Configuration Optional Keycap ConfigurationKey Descriptions Entry see Selection Mode Rules Primary Functions Quick Access ALMDisplay Radio Status IconsMessages Message Name DescriptionTX Data WHC=1 FIX List Spkr on Autokey Trunked Mode only Call Queued Trunked Mode onlySystem Busy Trunked Mode only Alert TonesCall Denied Trunked Mode only Carrier Control TimerDual Control Switching OperationSelection Mode Rules Turning on the RadioDirect Access U T HMenu N U K L G H T Press SEL Menu Item Information Feature Display Parameter Comment Settings SYS Scan Feature Encryption Display Feature Encryption Data StreamSerial Number ROM 12 Hex Digits Example Features Enabled Number FieldsBIT Fields Possible Features SYSTEM/GROUP/CHANNEL Selection System SelectionGroup And Channel Selection Trunked Mode Operation Receiving a CallSending a Call Conventional Failsoft Emergency OperationReceiving An Emergency Call System Scan Operation Declaring An Emergency CallWide Area System Scan ProSoundTM ProScanTMWhen Wide Area System Scan Is Enabled When ProSound/ProScan Is EnabledPriority System Scan Menu SelectionGroup Scan Operation Adding Groups To a Scan List Deleting Groups From a Scan ListNuisance Delete Turning Scan onPriority Group Scanning Individual Calls Turning Scan OFFReceiving and Responding To An Individual Call Page Scat Operation Sending An Individual CallReceiving a Telephone Interconnect Call Trunked Mode Only Sending a Telephone Interconnect Call Trunked Mode OnlyTelephone Interconnect Calls Dtmf Overdial/Conventional Mode Telephone Interconnect Programmable Entries Mobile Data DisplaysData OFF Operation Data On OperationScan Lockout Mode Exiting Data CallsData Lockout Mode STATUS/MESSAGE OperationStatus Operation Edacs Conventional P1 Scan Message OperationConventional Mode Operation Dynamic Regroup OperationEmergency Operation Receiving a Call Using 5-Tone Signalling for Emergency Declaration Tone Encode TransmissionScanning Conventional Channels Adding Channels To a Scan List Deleting Channels From a Scan ListTurning Scan on Turning Scan OFFSquelch Adjust Noise Blanker Operation Type 99 Decode Conventional OnlyMenu Selection Direct Mode Operation Conventional System Only Trunked or Conventional Mode Operation SIREN/LIGHT OperationVoice Modes AEGIS/ProVoice Digital Mode YesClear Modes Error Messages ERR=xxxxPage Transferring Keys Into The Radio Displaying The Currently Used Cryptographic Key NumberKey Zero Private Operation Receiving An Encrypted CallTransmitting An Encrypted Call Scanned Group Calls Conventional Operation Outside AddressSwitching Control Control Switching ModesDual Control Operation Channel GuardSlaved Mode Operation Independent Mode OperationSiren And Light Control Multiple Radio Operation Dual Control AudioChanging Selected Radio Shared Control Unit Display ModesFirst Come First Serve Display Audio ModesAudio Summed Audio First Come First ServeMacro KEY Operation Page Keypad Remapping Operating Rules and Regulations Glossary Group Or Subfleet Group Scan Individual Call Queueing SiteController SystemTalk-around TelephoneInter ConnectOperators Radio Setup Radio Type Frequency Band Operators Name Emergency GroupWarranty Emergency Numbers Operating Tips