Orion LBI-38888K manual Receiving a Call

Page 55

RECEIVING A CALL

1.Turn ON the radio by rotating the POWER ON-OFF/VOLUMEknob clockwise (out of detente). A short alert signal (if enabled through programming) indicates the radio is ready to use.

2.Adjust the POWER ON-OFF/VOLUMEknob to the desired volume level.

3.Select the desired conventional system and channel. The display indicates the current conventional system and channel names.

4.The radio is now ready to receive calls.

5.When the radio receives a call (and the correct encoding is decoded, if programmed and enabled), it unmutes on the channel and the BSY indicator comes on.

SENDING A CALL

1.Turn ON the radio and set the POWER ON-OFF/VOLUMEknob to the desired volume level. Select the desired conventional system and channel.

2.Ensure that the channel is not busy by pressing the c button to momentarily disable any channel decoding and unmute the receiver or observe the unlit BSY indicator. If the Channel Busy Lockout feature is programmed for the selected channel, the radio will not transmit when the channel is busy.

3.Press and hold the PTT button. The TX indicator will turn on and a short beep sounds (if programmed) indicating that communication can begin.

4.Hold the microphone approximately three inches from the mouth and speak in a normal voice.

5.Release the PTT button when the transmission is complete and listen for a reply.

EMERGENCY OPERATION

If enabled, G-STAR emergency signalling can be transmitted when operating in the conventional mode. This G-STAR signalling will transmit 5 times with a delay between each transmission. To send an emergency call on the selected conventional system and channel (or on an optionally pre-

55

Image 55

Contents Orion Product Specification for CE Marked Equipment Table of Contents Table of Contents Dynamite Blasting Caps Safety InformationList of the possible hazards are Explosive Atmospheres Interference To Vehicular Electronic SystemsUser Interface IntroductionOrion Mobile Radio System Model Front Panel Controls Power ON-OFF Volume KnobSYSTEM/GROUP Channel Knob Scan ADD/DELETE IndicatorsRamp Control Scan ON/OFFOrion System Model Keypad KeypadOptional Keycap Configuration Standard Keycap ConfigurationKey Descriptions Entry see Selection Mode Rules ALM Primary Functions Quick AccessRadio Status Icons DisplayMessage Name Description MessagesTX Data WHC=1 FIX List Spkr on Alert Tones Autokey Trunked Mode onlyCall Queued Trunked Mode only System Busy Trunked Mode onlyOperation Call Denied Trunked Mode onlyCarrier Control Timer Dual Control SwitchingTurning on the Radio Selection Mode RulesU T H Direct AccessMenu N U K L G H T Press SEL Menu Item Information Feature Display Parameter Comment Settings SYS Scan Feature Encryption Data Stream Feature Encryption DisplaySerial Number ROM 12 Hex Digits Example Number Fields Features EnabledBIT Fields Possible Features System Selection SYSTEM/GROUP/CHANNEL SelectionGroup And Channel Selection Receiving a Call Trunked Mode OperationSending a Call Emergency Operation Conventional FailsoftReceiving An Emergency Call Declaring An Emergency Call System Scan OperationWide Area System Scan ProScanTM ProSoundTMMenu Selection When Wide Area System Scan Is EnabledWhen ProSound/ProScan Is Enabled Priority System ScanGroup Scan Operation Deleting Groups From a Scan List Adding Groups To a Scan ListTurning Scan on Nuisance DeletePriority Group Scanning Turning Scan OFF Individual CallsReceiving and Responding To An Individual Call Page Sending An Individual Call Scat OperationSending a Telephone Interconnect Call Trunked Mode Only Receiving a Telephone Interconnect Call Trunked Mode OnlyTelephone Interconnect Calls Dtmf Overdial/Conventional Mode Telephone Interconnect Programmable Entries Displays Mobile DataData On Operation Data OFF OperationExiting Data Calls Scan Lockout ModeSTATUS/MESSAGE Operation Data Lockout ModeStatus Operation Message Operation Edacs Conventional P1 ScanDynamic Regroup Operation Conventional Mode OperationEmergency Operation Receiving a Call Tone Encode Transmission Using 5-Tone Signalling for Emergency DeclarationScanning Conventional Channels Deleting Channels From a Scan List Adding Channels To a Scan ListTurning Scan OFF Turning Scan onSquelch Adjust Type 99 Decode Conventional Only Noise Blanker OperationMenu Selection Direct Mode Operation Conventional System Only SIREN/LIGHT Operation Trunked or Conventional Mode OperationVoice Modes Yes AEGIS/ProVoice Digital ModeClear Modes ERR=xxxx Error MessagesPage Displaying The Currently Used Cryptographic Key Number Transferring Keys Into The RadioPrivate Operation Receiving An Encrypted Call Key ZeroTransmitting An Encrypted Call Conventional Operation Outside Address Scanned Group CallsChannel Guard Switching ControlControl Switching Modes Dual Control OperationIndependent Mode Operation Slaved Mode OperationSiren And Light Control Shared Control Unit Display Modes Multiple Radio OperationDual Control Audio Changing Selected RadioAudio First Come First Serve First Come First Serve DisplayAudio Modes Audio SummedMacro KEY Operation Page Keypad Remapping Operating Rules and Regulations Glossary System Group Or Subfleet Group Scan Individual Call QueueingSite ControllerConnect Talk-aroundTelephone InterRadio Type Frequency Band Operators Name Emergency Group Operators Radio SetupWarranty Operating Tips Emergency Numbers