JVC BR-DV6000U instruction manual Recording, Setting

RECORDING – Setting –

								OPERATE
Mini	MENU	DISP	RESET	PROFESSIONAL	A.DUB		REC	PLAY	PAUSE
	SEARCH–	SET	SEARCH+
					EJECT		REW	STOP	FF
MIC	HOLD	BLANK	CUE UP
	PHONES	REC LEVEL					AUDIO	INPUT	REMOTE
					COUNTER MONITOR OUTPUT SELECT
					CTL	L	CH-1/2	DV
					TC	MIX	MIX	LINE
		CH-1/3	CH-2/4	BR-DV6000	UB	R	CH-3/4	Y/C	LOCAL
								(CPN)

INPUT SELECT switch

Selecting input signal

Select the signal with the INPUT SELECT switch located on the front panel.

DV : For inputting DV signals (video and audio)

LINE : For inputting composite video and

analog sound signals

Y/C (CPN) : For inputting Y/C separate signals or component signals for video.The type of signal to input can be se- lected with VIDEO INPUT SEL of the VIDEO Menu.

For sound, analog signals are in- put.

Memo

●For analog audio signals, if the AUDIO IN terminal and MIC terminal are used at the same time, the MIC terminal precedes.

●Audio signals are recorded on CH1 and CH2.

●Analog signals cannot be recorded when PB/ DV IN is set to PAL.

In such a case, recording is not possible.

●For DV signal input, the AUDIO MODE set- ting cannot be performed.

It will be the same mode as that of the input signal (48 K or 32 K).

Settings the VIDEO Menu (☞ Page 79)

● SET UP (only for NTSC)

Set here according to the existence of the setup of analog video signals (composite, YC sepa- rate and component). If it exists, set here to ON. If it does not, OFF.

● BLACK BURST

Set BLACK BURST to ON to record the black burst signals (black screen) of the built-in sig- nal generator.

(When analog input is selected)

Settings of the AUDIO menu (☞ Page 78)

● AUDIO MODE

This is for selecting the audio sampling fre- quency for recording.

32 K: Recording in the 32 kHz mode. Select 32 K when performing audio dubbing on CH3 and CH4.

48 K: Recording in the 48 kHz mode. Audio dub- bing is not available.

● AUDIO INPUT SEL (Displayed only when an optional board is installed)

This setting is required with XLR IN board SA- X61U (sold separately) installed. Set this item to XLR for selecting the audio input terminal of the XLR IN board.

Setting the SYSTEM Menu (☞ Page 73)

● LONG PAUSE TIME

This is for setting the time for BR-DV6000 to enter the tape protection mode if there is a long recording pause.

● INDEX WRITE: SYSTEM (2/2) Menu

This is for selecting whether to record index sig- nals automatically when recording starts.

● PB/DV IN: SYSTEM (2/2) Menu

For recording NTSC signals, set this item to NTSC.

For recording PAL signals from the DV termi- nal, set this item to PAL.

Setting the time code recording for DV signal input

Select data from the built-in time code genera- tor or from the DV terminal with TC DUPLICATE

in the TC/UB/CLOCK (1/2) Menu screen. (☞ Page 80)

Setting date/time recording

Perform setting for the following items.

•Set DATE REC in the TC/UB/CLOCK (2/2) Menu screen to ON.

•Set DISPLAY in the DISPLAY (1/2) Menu screen to ON.

•Set TIME/DATE in the DISPLAY (2/2) Menu

screen to any setting item except OFF.

The same data as on the date/time on-screen display are added to the image and recorded.

Memo

With DV signal input, data of the built-in clock are not recorded.

If video signals are input from the DV terminal, the date/time data from this terminal are re- corded regardless of the menu settings.

42