JVC BR-DV6000U instruction manual Command Description

Table	Command	Description
J1	B0	VISS FORWARD :
		Index search in the forward direction.
		For the index search position, enter a
		3-digit number (001-099) following the
		command.
		When a 3-digit number has been en-
		tered, index search starts.
		If ENTER (40H) is transmitted before
		all three digits are entered, the remain-
		ing digit(s) are considered as Ò0Ó (30H),
		and index search starts.
J1	B1	VISS REV :
		Index search in the reverse direction.
		For the index search position, enter a
		3-digit number (001-099) following the
		command.
		When a 3-digit number has been en-
		tered, index search starts.
		If ENTER (40H) is transmitted before
		all three digits are entered, the remain-
		ing digit(s) are considered as Ò0Ó (30H),
		and index search starts.
B	B2	CUE UP WITH DATA :
		Use this command to cue up a speci-
		fied point on the tape. When the tape
		is cued, COMPLETION is returned
		and the Pause mode becomes effec-
		tive.
		To specify a cue point, transmit the
		time data (hour: minute: second: frame,
		a total of 8 bytes with 2 bytes for each)
		following this command. By transmit-
		ting ENTER (40H) with the time data,
		transmission of lower data becomes
		unnecessary. In such a case, Ò0Ó is
		transmitted. If the specified point can-
		not be found, NOT TARGET (05H) is
		returned.
J1	B2	CUE UP AND PLAY WITH DATA:
		Use this command to cue up a speci-
		fied point on the tape. When the tape
		is cued, COMPLETION is returned
		and the Play mode becomes effective.
		To specify a cue point, transmit the
		time data (hour: minute: second: frame,
		a total of 8 bytes with 2 bytes for each)
		following this command. By transmit-
		ting ENTER (40H) with the time data,
		transmission of lower data becomes
		unnecessary. In such a case, Ò0Ó is
		transmitted. If the specified point can-
		not be found, NOT TARGET (05H) is
		returned.

Table	Command	Description
J1	B5	F-SHUTTLE :
		Shuttle play. The search speed is
		specified by sending the speed code
		data after this command (see the ta-
		ble below).
		Speed code table
		(Supported speed only)
		Speed code	Search speed
		30h	STILL
		31h	0.1
		32h	0.2
		33h	0.33
		34h	0.5
		35h	1
		36h	2
		37h	5
		38h	10
		39h	20
		3Bh	X0.90
		3Ch	X1.07
		3Bh and 3Ch are effective only for B5.
	B6	R-SHUTTLE :
		Shuttle reverse play.The search speed
		is specified by sending the speed code
		data after this command (see the ta-
		ble above).
B	CO	AUTO EDIT KEY :
		Audio editing with the VCR.

¥It is required that the editing chan- nel is selected in [E5: Edit Preset].

¥This audio editing command must be used with [FA: Rec Request].

¥Preroll time can be set with [E6: Preroll Time Preset]. Without this setting, the VCR menu switch set- tings are followed.

¥Upon the completion of auto editing,

the VCR returns [01: Complete].

BC1 PREVIEW KEY : Preview with the VCR

¥It is required that the editing chan- nel is selected in [E5: Edit Preset].

¥This preview command must be used with [FA: Rec Request].

¥Preroll time can be set with [E6: Preroll Time Preset]. Without this setting, the VCR menu switch set- tings are followed.

¥Upon the completion of preview, the VCR returns [01: Complete].

87