JVC BR-DV6000U instruction manual Editing procedure with BR-DV6000,  Remote 1/2 Menu screen

Page 66

EDIT – Editing with an RS-422A/JVC bus edit remote controller – (continued)

Editing procedure with BR-DV6000

:Connection:

For details on connection, refer to pages 32 and 33.

:Setting:

Set the REMOTE/LOCAL switch on the front panel to REMOTE.

SYSTEM (1/2) Menu screen

SYNC SELECT : If there is no input of synchronization signals to the SYNC IN terminal, set this item of the recorder to AUTO. During playback, it synchronizes with the input video signal.

REMOTE (1/2) Menu screen

•Set REMOTE SEL 9-PIN to ON (for RS-422A).

Memo : To use the REMOTE 2 (12-PIN) terminal simultaneously, set REMOTE SEL JVC to ÒOFFÓ.

•Set REMOTE SEL JVC to ON (for JVC-BUS).

Memo : To use the REMOTE 1 (9-PIN) terminal simultaneously, set REMOTE SEL 9-PIN to ÒOFFÓ.

•PREROLL:

Use this item to set the preroll time (second). It is recommended that at least 7 seconds be set. Memo : The setting by the editing remote controller precedes if applicable.

REMOTE (2/2) Menu screen

•REM STOP SEL (only for RS-422A)

Select the mode for BR-DV6000 to be in when it receives standby-on signals.

EE : EE mode (STOP mode)

PB : Playback mode (STILL mode)

•PB START DELAY

Set the editing timing. If the start points of edit are not concurrent, adjust the playback startup timing.

0F : No correction

1F-15F : Delays the timing for the duration of the set frames. If BR-DV6000 is connected to an editing remote controller with no bump function, use this setting to adjust the edit precision.

Memo : No bump function is available for RM-G800/G805.

•SYNCHRONIZATION (only for RS-422A)

Whether to use the bump function to enhance edit precision can be selected. OFF : Bump off

ON : Bump on. It may slow down the edit operation.

•CONTROLLER SEL (only for RS-422A)

Set this item according to the type of controller to be connected. (☞ Refer to Page 77) Set it to TYPE 1 when RM-G820 is used.

TC OFFSET in the TC/UB/CLOCK (1/2) Menu screen (only for RS-422A)

To edit DV signals, set the timing for the time code to be output to the editing controller form BR- DV6000.

Usually, this item is set to OFF.

To edit with DV connection

¥ Set the player input selection to other than DV.

¥ If the bump function is to be used, operate the function from the player. In the case of an editing remote controller for which the function is operated from the recorder, set the preroll time to at least 10 seconds.

¥ For both player and recorder, set REM STOP SEL to PB.

66

Page 65 Page 67
Image 66
Page 65 Page 67
Contents DV Video Cassette Recorder LLT0033-001C-HS3125A Remarque Reorient or relocate the receiving antennaCompatible mechanisms for standard/mini DV cas- sette tapes Backup recording functionDV format Sync in terminalTable of Contents  Place of storage and use IntroductionRemarks of usage  Handling the unit Head cleaning Regular maintenance Regular maintenance Maintenance consultationMemo Cleaning tapeCassette tape Remarks on the use of tapeIt is used at a place of high humidity CondensationOver 10 years Head drum VideotapeCassette loading slot/LED Names and Functions of PartsFront panel Operate button/LED FF button/LED  Play button/LED Pause button/LED  Stop button4REMOTE/LOCAL switch Input Select switch Audio Output switch MemoSwitching is invalid during recording Audio Monitor switch Counter switch The following information is also dis- played CH2/4 Reset button@PHONES Headphone volume Menu buttonSpecial functions/Setting buttons Video Y/C in terminal 4-PIN Rear panelVideo Line in terminal BNC Video Line OUT terminal BNCTime Code OUT terminal BNC Sync in synchronization input Terminal BNCTime Code in terminal BNC CH1/3 Audio in terminal RCASignal GND terminal DC power input terminal 2-PIN Timer recording/playbackSwitch DC power cord clamp Mini jack› Remote 2 JVC Bus terminal 12-PIN ¤ Serial Remote OUT terminal mini jack‹ Remote 1 RS-422A terminal Slot cover for an optional boardON-SCREEN Display On-screen displayOn-screen display Description Operation Sampling frequency/audio Status displayMemo Output CHCounter display 00 00 00Display Description Insert editing in the 32 k audio modeStatus/Event display Display displayed during operationAlarm display Blank DUB Inhibit DUB InhibitREC TAB Dvcam Edit Inhibit LCD display mode enlarged display LCD displayLCD It is displayed when condensation occurs Displays the framing mode of the time codeDisplays the operation mode of the VCR Non-drop frame Input signal Connecting video signals Output signal ConnectionPlayback  Synchronization signalYes RecordConnecting audio signals Audio Output switches and output channelsHeadphone terminal Microphone input terminal Connecting to a monitor TVDigital output Digital input Remote extension cable Connecting to editing sytem Related VCRs  DV cable When an RS-422A-compatible remote controller is used Connection Connection with serial remote terminals Dubbing with 1 VCRAlarm message Connecting the AC adapterDC in terminal Timer switch Connect the supplied AC adaptor to BR-DV6000Turning on/off the power Turning on the powerTurning off the power PreparationRemote controller and operation lock mode Selecting the operating method main unit/remote controllerOperation Lock mode Operation method main unitLoading the cassette tape Ejecting the cassette tapeLoading/Ejecting cassette Setting the display time of the LCD display Setting the LCD displayAdjusting the LCD display  Selecting the LCD status displaySetting date and time Setting/Displaying date and timeSetting the date and time in the Clock Adjust Menu screen Selecting date/time display On-screen status display Display 2/2 Menu screen Setting RecordingRecording index signals Recording procedurePress the Pause button while holding down the A.DUB button Audio dubbingPress the Play button to play the tape Press the Play buttonMinute tape RECORDING- Backup recording function For using GY-DV5000 as the source unit 115MIN Minute tape 175MIN 265MINBR-DV6000 Serial remote controller RM-G30, sold separately can be conRecording Recording with serial remote terminals Output from the Serial Remote OUT terminal. Only with OperSet the time, etc., of the external timer External timer recordingAdjust the recording level of sound LCD display System Menu screen  Setting the switches on the front panelPlayback  Video MenuBasic playback procedure Playback of tapes recorded in the PAL formatFast forward/rewind Special playback functions Search modeFrame-advance playback Search speedIncreasing the playback speed by 7% Decreasing the playback speed by 10%REW button Search function Index searchBlank search  In the Stop mode, press the Blank buttonRepeat operation  Repeat Mode in the System 1/2 Menu screenRepeat playback Index repeat playbackClearing registered cue-up points For details on time code setting and recordingRegistering cue-up points Multi cue-upChanging cue-up points Exiting the Multi Cue-up screenSearching cue-up points Set up the time, etc., of the external timer External timer playbackMode, the timer symbol lights up in green  Connect the supplied AC adapter BR-DV6000  Dubbing machineTime Code Displaying the time codePresetting the time code TCG Source Internal TCG Select Preset Recording from preset dataPreset time code Recording the time codeTCG Source TCG ModeRecording time code, input to the DV IN/OUT terminal TCG Select TC/UB/CLOCK1/2 Menu screen  Front switchesRecord time codes from an external time code generator Set TCG Source to ÒexternalóPlaying back the time code Set the Counter switch to Òtcó or ÒubóPress the Play button to go to the Playback mode Monitor / LCD Status displayKHz mode Edit Editing with an RS-422A/JVC bus edit remote controllerEdit mode Analog editing Mode select Yes*2AUD-1  Following editing mode is not availableEdit mode DV editing Mode select AUD-2 AUD-1 Remote 2/2 Menu screen Editing procedure with BR-DV6000 Remote 1/2 Menu screen  To edit with DV connectionMaking prerecorded base tape used as editing recorder  Setting the Time Code mode used as editing recorder Setting of RM-G820 Confirmation by preview editingEdit Using a non-linear editing systemRemote FF/REW Mode Controller Type in the Remote 2/2 Menu screenMenu Screens Structure of the Menu screensDisplaying the Menu screen items for setting Setting the menus Set BR-DV6000 to the Stop or Still mode TOP Menu screenSystem 2/2 Menu screen Description of the Menu screens TOP Menu screenSystem Menu screens  System 1/2 menu55MIN Backup REC25MIN 75MINMenu Screens Description of the Menu screens  System 2/2 MenuRemote Menu screens  Remote 1/2 Menu screen Remote 2/2 Menu screen Synchroni DelayPB Start ZationAudio Menu screen Video Menu screen TC/UB/CLOCK Menu screens  TC/UB/CLOCK 1/2 Menu screenBIT PAL Adjust TC/UB/CLOCK 2/2 Menu screen Date RECDisplay Menu screens  Display 1/2 Menu screen Display 2/2 Menu screen Command tables RS-232C Interface 9PIN D-Sub Pin No RS-232C specificationsAscii code table RxDRS-232C commands  PreparationCommand Description Return commands from the VCR Error commandsExample of Clear Error RS-232C Interface RS-232C commands  Second byte  Setup preset commands First byte Bit No Status If the bit is  Third byteExample Check the Sync Select setting  Menu switch setup commandED Memory SW Preset B/J1 Example Set Sync Select to ExternalMenu  System MenusD1/D2 Set value Corresponding bit values D1/D2Remote Menus Menu Set value Audio Menus  Video Menus TC/UB/CLOCK Menus  Display Menus MAX512H 24H  Alarm display Displayed regardless of the Display mode Others Warning display Displayed regardless of the Display mode Troubleshooting ¥ The System 1/2 Menu screen is displayed  Set BR-DV6000 to the Stop modeChecking the hour meter Press the Menu button to return to the normal screen RS-232C interface board SA-K46U  XLR in board SA-X61U Installing SA-X61U or SA-X62UOptional devices  XLR OUT board SA-X62UHexagonal screws Installing SA-K46U RS-232C interface boardInstall the SA-K46U Remove the RS-422A Remote 1 terminalSpecifications  External dimensions Unit mm 212Supplement AC adapter sectionVictor Company of JAPAN, Limited
Top Page Image Contents