JVC BR-DV6000U instruction manual  Synchronization signal, Yes, Playback, Record

Page 29

Caution on video signals

If search images or video signals with a high level of jitter are input, images or sound may be distorted temporarily. Thus, input stable signals, e.g., those having gone through a TBC.

A digital VCR requires that video signals for recording be delivered from a stable source. Video signals from an analog VCR must be run through a TBS or TBC.

When a component output is executed for composite-input video, discoloration may oc- cur on the left side of the screen. It is not a defect.

Synchronization signal

In order to enhance the level of edit precision, input synchronization signals to all the devices of the editing system during editing.

For BR-DV6000, input external synchronization signals into the SYNC IN terminal. For external synchronization signals, use video signals of 1V (p-p) or lower (e.g., black burst signals).

To edit DV signals, synchronization signal in- put is required.

Types of synchronization signal: BR-DV6000 is operated based on one of the following 3 types of synchronization signal.

Synchronization signals produced by the syn- chronization signal generator inside the VCR (INT)

Video signals from the video signal input ter- minal (VIDEO)

Synchronization signals from the SYNC IN

terminal (EXT)

Selection of synchronization signals: Synchronization signals should be selected de- pending on whether external synchronization input (SYNC IN) or video input (VIDEO IN) ex- ists or on the SYNC SELECT Menu settings. Synchronization signals are selected as shown in the following table.

SYNC IN

No

Yes

No

Yes

VIDEO IN

No

No

Yes

Yes

EXTERNAL

Playback

INT

EXT

INT

EXT

Record

INT

INT

VIDEO

VIDEO

 

 

 

 

 

 

 

AUTO

Playback

INT

EXT

VIDEO

EXT

 

 

 

 

 

Record

INT

INT

VIDEO

VIDEO

 

 

 

 

 

 

 

The above can be selected with SYNC SE- LECT in the SYSTEM Menu screen.

Memo

During DV signal recording, the status of synchronization signals will be as shown be- low regardless of the SYNC SELECT menu settings.

SYNC IN terminal

Synchronization

signal

signals

Input

EXT

No input

DV

Regardless of the setting of SYNC SELECT, when a tape recorded in PAL is played back, synchronization signals are as shown below.

SYNC IN terminal

Synchronization signals

PAL signal input

EXT

NTSC signal input or

INT

No signal input

 

Caution on synchronization signals

For external synchronization signals, output- signal phase adjustments cannot be per- formed. In addition, the sub carrier cannot be locked.

Plugging and unplugging of external synchro- nization signals or video input signals during playback causes distortion of images and sound for about 5 seconds.

29

Image 29
Contents LLT0033-001C-H DV Video Cassette RecorderS3125A Reorient or relocate the receiving antenna RemarqueDV format Backup recording functionCompatible mechanisms for standard/mini DV cas- sette tapes Sync in terminalTable of Contents Remarks of usage Introduction Place of storage and use  Handling the unit Regular maintenance Regular maintenance Head cleaning Maintenance consultationCassette tape Cleaning tapeMemo Remarks on the use of tapeOver 10 years CondensationIt is used at a place of high humidity Head drum VideotapeFront panel Names and Functions of PartsCassette loading slot/LED Operate button/LED Pause button/LED  Play button/LED FF button/LED  Stop buttonSwitching is invalid during recording 4REMOTE/LOCAL switch Input Select switchAudio Output switch Memo  The following information is also dis- played Audio Monitor switchCounter switch @PHONES Headphone volume Reset buttonCH2/4 Menu buttonSpecial functions/Setting buttons Video Line in terminal BNC Rear panelVideo Y/C in terminal 4-PIN Video Line OUT terminal BNCTime Code in terminal BNC Sync in synchronization input Terminal BNCTime Code OUT terminal BNC CH1/3 Audio in terminal RCASwitch DC power input terminal 2-PIN Timer recording/playbackSignal GND terminal DC power cord clamp Mini jack‹ Remote 1 RS-422A terminal ¤ Serial Remote OUT terminal mini jack› Remote 2 JVC Bus terminal 12-PIN Slot cover for an optional boardOn-screen display Description Operation ON-SCREEN DisplayOn-screen display Memo Status displaySampling frequency/audio Output CH00 00 00 Counter displayStatus/Event display Insert editing in the 32 k audio modeDisplay Description Display displayed during operationAlarm display REC TAB DUB InhibitBlank DUB Inhibit Dvcam Edit InhibitLCD  LCD display mode enlarged displayLCD display Displays the operation mode of the VCR Displays the framing mode of the time codeIt is displayed when condensation occurs Non-drop frame Output signal Connecting video signals Input signal ConnectionYes  Synchronization signalPlayback RecordHeadphone terminal Connecting audio signalsAudio Output switches and output channels Digital output Connecting to a monitor TVMicrophone input terminal Digital input Related VCRs Connecting to editing sytem Remote extension cable  DV cable When an RS-422A-compatible remote controller is used Dubbing with 1 VCR Connection Connection with serial remote terminalsDC in terminal Timer switch Connecting the AC adapterAlarm message Connect the supplied AC adaptor to BR-DV6000Turning off the power Turning on the powerTurning on/off the power PreparationOperation Lock mode Selecting the operating method main unit/remote controllerRemote controller and operation lock mode Operation method main unitLoading/Ejecting cassette Loading the cassette tapeEjecting the cassette tape Adjusting the LCD display Setting the LCD displaySetting the display time of the LCD display  Selecting the LCD status displaySetting the date and time in the Clock Adjust Menu screen Setting date and timeSetting/Displaying date and time  Display 2/2 Menu screen Selecting date/time displayOn-screen status display Recording SettingRecording procedure Recording index signalsPress the Play button to play the tape Audio dubbingPress the Pause button while holding down the A.DUB button Press the Play button For using GY-DV5000 as the source unit RECORDING- Backup recording functionMinute tape 115MIN Minute tape 175MIN 265MINRecording Recording with serial remote terminals Serial remote controller RM-G30, sold separately can be conBR-DV6000 Output from the Serial Remote OUT terminal. Only with OperAdjust the recording level of sound External timer recordingSet the time, etc., of the external timer LCD displayPlayback  Setting the switches on the front panel System Menu screen  Video MenuFast forward/rewind Basic playback procedurePlayback of tapes recorded in the PAL format Frame-advance playback Search modeSpecial playback functions Search speedREW button Increasing the playback speed by 7%Decreasing the playback speed by 10% Blank search Index searchSearch function  In the Stop mode, press the Blank buttonRepeat playback  Repeat Mode in the System 1/2 Menu screenRepeat operation Index repeat playbackRegistering cue-up points For details on time code setting and recordingClearing registered cue-up points Multi cue-upSearching cue-up points Changing cue-up pointsExiting the Multi Cue-up screen Mode, the timer symbol lights up in green External timer playbackSet up the time, etc., of the external timer  Connect the supplied AC adapter Dubbing machine  BR-DV6000Displaying the time code Time CodePresetting the time code Preset time code Recording from preset dataTCG Source Internal TCG Select Preset Recording the time codeRecording time code, input to the DV IN/OUT terminal TCG ModeTCG Source TCG SelectRecord time codes from an external time code generator  Front switches TC/UB/CLOCK1/2 Menu screen Set TCG Source to ÒexternalóPress the Play button to go to the Playback mode Set the Counter switch to Òtcó or ÒubóPlaying back the time code Monitor / LCD Status displayEdit mode Analog editing Mode select Edit Editing with an RS-422A/JVC bus edit remote controllerKHz mode Yes*2Edit mode DV editing Mode select  Following editing mode is not availableAUD-1 AUD-2 AUD-1 Remote 1/2 Menu screen Editing procedure with BR-DV6000 Remote 2/2 Menu screen  To edit with DV connection Setting of RM-G820  Setting the Time Code mode used as editing recorderMaking prerecorded base tape used as editing recorder Confirmation by preview editingRemote FF/REW Mode Using a non-linear editing systemEdit Controller Type in the Remote 2/2 Menu screenStructure of the Menu screens Menu Screens Set BR-DV6000 to the Stop or Still mode Setting the menusDisplaying the Menu screen items for setting TOP Menu screenSystem 2/2 Menu screen System Menu screens TOP Menu screenDescription of the Menu screens  System 1/2 menu25MIN Backup REC55MIN 75MIN System 2/2 Menu Menu Screens Description of the Menu screens Remote 1/2 Menu screen Remote Menu screens Remote 2/2 Menu screen PB Start DelaySynchroni ZationAudio Menu screen Video Menu screen  TC/UB/CLOCK 1/2 Menu screen TC/UB/CLOCK Menu screens TC/UB/CLOCK 2/2 Menu screen AdjustBIT PAL Date REC Display 1/2 Menu screen Display Menu screens Display 2/2 Menu screen RS-232C Interface Command tablesAscii code table RS-232C specifications 9PIN D-Sub Pin No RxD Preparation RS-232C commandsCommand Description Error commands Return commands from the VCRExample of Clear Error RS-232C Interface RS-232C commands  First byte Bit No Status If the bit is  Setup preset commands Second byte  Third byteED Memory SW Preset B/J1  Menu switch setup commandExample Check the Sync Select setting Example Set Sync Select to ExternalD1/D2  System MenusMenu Set value Corresponding bit values D1/D2Menu Set value Remote Menus TC/UB/CLOCK Menus  Audio Menus Video Menus 12H 24H  Display MenusMAX5 Others  Alarm display Displayed regardless of the Display mode Warning display Displayed regardless of the Display mode Troubleshooting Checking the hour meter  Set BR-DV6000 to the Stop mode¥ The System 1/2 Menu screen is displayed Press the Menu button to return to the normal screenOptional devices Installing SA-X61U or SA-X62U RS-232C interface board SA-K46U  XLR in board SA-X61U  XLR OUT board SA-X62UInstall the SA-K46U Installing SA-K46U RS-232C interface boardHexagonal screws Remove the RS-422A Remote 1 terminalSpecifications 212  External dimensions Unit mmAC adapter section SupplementVictor Company of JAPAN, Limited