Lincoln Electric SVM197-A service manual Procedure

Page 75

Section TOC

Master TOC

F-27

TROUBLESHOOTING AND REPAIR

F-27

BRUSH REMOVAL AND REPLACEMENT (continued)

PROCEDURE (continued)

Return to

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to

Return to Master TOC

Return to Master TOC

Return to Master TOC

8.To reinstall the brush holder assem- bly, depress the spring-loaded brushes into the holder and slip a suitable non-metallic, fairly stiff retainer through the slots at the top and bottom of the holder. A cable tie works well; see Figure F.7. This will hold the brushes up so that you can easily install the holder.

9.With the needle nose pliers, rein- stall the two white wires to the appropriate terminals on the brush- es. Lead 202A is inboard.

10.Slip the holder into position in the generator end bracket. Be careful not to loosen the 2 attached wires.

11.Reinstall and tighten the 2 screws with the 1/4” nut driver.

12.Slowly remove the non-metallic retainer from the brush holder and let the brushes snap back against the slip rings.

13.Check the wire connections or clearance and tightness.

14.Snap the brush holder cover back into position.

POWERARC® 5500

Image 75

Contents Powerarc ISAFETYi Electric Shock can kill ARC Rays can burn SafetyIii For ElectricallyPrécautions DE Sûreté Electromagnetic Compatibility EMC Safety Master Table of Contents for ALL Sections Table of Contents Installation Section Technical Specifications Powerarc InstallationEngine Exhaust can kill Safety PrecautionsLocation and Ventilation StoringPRE-OPERATION Engine Service Honda 9 HP PowerArc 5500 Typical Fuel ConsumptionMuffler Deflector Spark ArresterCable Size and Length Powerarc 5500 Output ConnectionsElectrical Output Connections Welding Cable ConnectionsMachine Grounding Auxiliary Power ReceptaclesCable Installation Plugs and HAND-HELD EquipmentCircuit Breakers Premises WiringType Common Electrical Devices Possible Concerns Table A.2 Electrical Device USE with the PowerarcPowerarc Table of Contents Operation Section Operation Physical Location of Components may vary by Code No Controls and SettingsLimitations Output Panel ControlsGasoline Engine Controls Engine OperationStarting the Engine Before Starting the EngineRunning the Engine Generator OperationStopping the Engine General InformationTable B.3 Generator Power Applications Control Function / Operation Current Control Dial Welding OperationWelding Guidelines Material Thickness Electrode Type Size SettingWelding circuit for Stick shielded metal arc welding What Happens in the Arc?Correct Welding Speed Correct Welding PositionCorrect Way to Strike An Arc Correct Arc LengthDo the following Common MetalsTypes of Welds Use the followingWelding in the Vertical Position PenetrationVertical-Down Welding Vertical-Up WeldingWelding Sheet Metal How to Hardface the Sharp Edge Metal to Ground WearOverhead Welding Hardfacing To Reduce WearCast Iron Plate Preparation Welding Cast IronOut-of-Position Group AWS E6011 Selecting ElectrodesHigh-Speed Group AWS E6013 Low Hydrogen Group AWS E7018Powerarc Table of Contents Accessories Section Accessories OPTIONS/ACCESSORIESLincoln Electric Accessories Table of Contents Maintenance Section Maintenance Routine and Periodic MaintenanceEngine Maintenance Figure D.3 Clean Rotating SCREEN/FINGER GUARD/DEBRIS Guard Engine AdjustmentsPart Robin / Subaru Honda Table D.1 Engine Maintenance PartsDo not attempt to polish slip rings while engine is running GENERATOR/WELDER MaintenanceFigure D.6. Major Component Locations 1TABLE of CONTENTS-THEORY of Operation Section E-1 Theory of Operation Engine Control and IgnitionENGINE, EXCITATION, Rotor and Stator Return Rotor Field Feedback Auxiliary PowerWeld Winding and Reactor Auxiliary Power Overcurrent Protection1TABLE of Contents Troubleshooting and Repair F-1 HOW to USE Troubleshooting Guide 2TROUBLESHOOTING and REPAIRF-2Troubleshooting and Repair Output Problems Perform the Rotor and Flashing Voltage Test Troubleshooting and Repair Troubleshooting and Repair Rotor Resistance Test Engine Problems Troubleshooting and Repair Engine Throttle Adjustment Test Powerarc Materials Needed Test DescriptionLead 14TROUBLESHOOTING and REPAIRF-14Rotor Voltage Test Procedure Flashing Voltage Test ProcedureRotor Resistance Test Procedure Rotor Resistance Test Procedure Figure F.3 Brushes Retained with Cable TIE Powerarc Engine Throttle Adjustment Test ROBIN/SUBARU Engine ROBIN/SUBARU Engine Engine Throttle Adjustment TestHigh Speed Stop Screw Scope Settings Normal Open Circuit Weld Voltage WaveformHigh Idle no Load Normal Open Circuit Voltage Waveform 115 VAC Supply Typical Weld Output Waveform Machine LoadedMachine Loaded to 125 Amps AT 23 VAC Brush Removal and Replacement Procedure Brush Removal and Replacement Procedure Powerarc Rheostat Removal and Replacement Procedure Rheostat Removal and Replacement Procedure Troubleshooting and Repair Attachment for 201 201A Jumper Procedure Capacitor Removal and REPLACE- MentCapacitor AND/OR Diode Bridge Attachment for 202A Cable Tie CapacitorFigure F.10 Field Diode Bridge Location Procedure Field Diode Bridge Removal and ReplacementPowerarc STATOR/ROTOR Removal and Replacement Procedure STATOR/ROTOR Stator Removal ProcedureSection TOC Rotor Removal Procedure Procedure Reactor Bolts Lead WELDER/GENERATOR OUTPUT1 Auxiliary Power Receptacle OUTPUT1Retest After Repair Engine OutputPowerarc Table of Contents Diagram Section Wiring Diagram Codes 11182, 11187, 11329 S25984 Electrical DiagramsSwitch Wiring Diagram Codes 11403, 11405 S26829Wiring Diagram Code 11404 S26830 Wiring Diagram Power ARCWiring Diagram Code 11215 S26023 S26008 Schematic -CODES 11182, 11187, 11329 S26008S26881 Schematic Codes 11403, 11405 S26881S26882 Schematic Code 11404 S26882