Lincoln Electric SVM197-A service manual Procedure

Page 87

TOC

F-39

TROUBLESHOOTING AND REPAIR

F-39

STATOR/ROTOR

REMOVAL AND REPLACEMENT PROCEDURE (continued)

Return to Section

Return to Section TOC

to Section TOC

Return to Master

Return to Master TOC

to Master TOC

6.Install the bottom two end bracket thru- bolts.

7.Tap the end bracket with the mallet as nec- essary to position it. Tighten the bolts to 4.5 - 5.5 ft lbs. Alternate tightening in order to pull the assembly together evenly. As you tighten, look through the brush housing access door and watch the bearing to judge end bracket movement and align- ment.

8.Check the rotor-stator air gap with the long

.010 feeler gauge. The measurement is taken through the brush holder access door; see Figure F14. Turn the engine with the recoil starter rope slightly so that the rotor “iron” is up to take the measurement. (The rotor has two flat sides, which are not measured for air gap.) Slide in the gauge. Then rotate the shaft 180 degrees and mea- sure again. If the gauge does not clear, loosen the four end bracket thru-bolts, reposition the end bracket, retighten the bolts, and recheck the air gap. Repeat until the proper .010 minimum air gap is achieved.

9.Tighten the end bracket support nuts and lock washers. Remove the 2 X 4 engine support.

10.Position the control box into place.

11.Reinstall the brush holder assembly. Refer to the Brush Removal and Replacement

Procedure.

12.Reconnect the output lead W2 to the output terminal.

13.Install a new cable tie to hold the leads together.

14.Reconnect the large molex plug.

15.Install the five sheet metal screws that secure the control box to the stator frame. Be sure to connect the green ground lead to the screw previously removed.

16.Reconnect the flashing lead #205 to diode D2. Secure lead in control box.

17.Using the 6 sheet metal screws previously removed, mount the control box panel to the control box.

18.Using the 1/2” wrench replace the 2 bolts and star washers securing the control box to the stator frame.

19.Carefully set the reactor in place and secure with the two remaining bolts and star wash- ers.

20.Reconnect the reactor leads.

21.Check all terminal connections for clear- ance, grounding, and tightness.

22.Replace the top cover to the control box and tighten the 8 screws.

23.Conduct the Retest After Repair Procedure.

Return

Return to Section TOC

Return

Return to Master TOC

FIGURE F.14 - CHECKING ROTOR-STATOR AIR GAP

FEELER GAUGE

STATOR

ROTOR

POWERARC® 5500

Page 86 Page 88
Image 87
Page 86 Page 88
Contents Powerarc ISAFETYi Electric Shock can kill ARC Rays can burn SafetyIii For ElectricallyPrécautions DE Sûreté Electromagnetic Compatibility EMC Safety Master Table of Contents for ALL Sections Table of Contents Installation Section Technical Specifications Powerarc InstallationEngine Exhaust can kill Safety PrecautionsLocation and Ventilation StoringPRE-OPERATION Engine Service Honda 9 HP PowerArc 5500 Typical Fuel ConsumptionMuffler Deflector Spark ArresterCable Size and Length Powerarc 5500 Output ConnectionsElectrical Output Connections Welding Cable ConnectionsMachine Grounding Auxiliary Power ReceptaclesCable Installation Plugs and HAND-HELD EquipmentCircuit Breakers Premises WiringType Common Electrical Devices Possible Concerns Table A.2 Electrical Device USE with the PowerarcPowerarc Table of Contents Operation Section Operation Physical Location of Components may vary by Code No Controls and SettingsLimitations Output Panel ControlsGasoline Engine Controls Engine OperationStarting the Engine Before Starting the EngineRunning the Engine Generator OperationStopping the Engine General InformationTable B.3 Generator Power Applications Control Function / Operation Current Control Dial Welding OperationWelding Guidelines Material Thickness Electrode Type Size SettingWelding circuit for Stick shielded metal arc welding What Happens in the Arc?Correct Welding Speed Correct Welding PositionCorrect Way to Strike An Arc Correct Arc LengthDo the following Common MetalsTypes of Welds Use the followingWelding in the Vertical Position PenetrationVertical-Down Welding Vertical-Up WeldingWelding Sheet Metal How to Hardface the Sharp Edge Metal to Ground WearOverhead Welding Hardfacing To Reduce WearCast Iron Plate Preparation Welding Cast IronOut-of-Position Group AWS E6011 Selecting ElectrodesHigh-Speed Group AWS E6013 Low Hydrogen Group AWS E7018Powerarc Table of Contents Accessories Section Accessories OPTIONS/ACCESSORIESLincoln Electric Accessories Table of Contents Maintenance Section Maintenance Routine and Periodic MaintenanceEngine Maintenance Figure D.3 Clean Rotating SCREEN/FINGER GUARD/DEBRIS Guard Engine AdjustmentsPart Robin / Subaru Honda Table D.1 Engine Maintenance PartsDo not attempt to polish slip rings while engine is running GENERATOR/WELDER MaintenanceFigure D.6. Major Component Locations 1TABLE of CONTENTS-THEORY of Operation Section E-1 Theory of Operation Engine Control and IgnitionENGINE, EXCITATION, Rotor and Stator Return Rotor Field Feedback Auxiliary PowerWeld Winding and Reactor Auxiliary Power Overcurrent Protection1TABLE of Contents Troubleshooting and Repair F-1 HOW to USE Troubleshooting Guide 2TROUBLESHOOTING and REPAIRF-2Troubleshooting and Repair Output Problems Perform the Rotor and Flashing Voltage Test Troubleshooting and Repair Troubleshooting and Repair Rotor Resistance Test Engine Problems Troubleshooting and Repair Engine Throttle Adjustment Test Powerarc Materials Needed Test DescriptionLead 14TROUBLESHOOTING and REPAIRF-14Rotor Voltage Test Procedure Flashing Voltage Test ProcedureRotor Resistance Test Procedure Rotor Resistance Test Procedure Figure F.3 Brushes Retained with Cable TIE Powerarc Engine Throttle Adjustment Test ROBIN/SUBARU Engine ROBIN/SUBARU Engine Engine Throttle Adjustment TestHigh Speed Stop Screw Scope Settings Normal Open Circuit Weld Voltage WaveformHigh Idle no Load Normal Open Circuit Voltage Waveform 115 VAC Supply Typical Weld Output Waveform Machine LoadedMachine Loaded to 125 Amps AT 23 VAC Brush Removal and Replacement Procedure Brush Removal and Replacement Procedure Powerarc Rheostat Removal and Replacement Procedure Rheostat Removal and Replacement Procedure Troubleshooting and Repair Attachment for 201 201A Jumper Procedure Capacitor Removal and REPLACE- MentCapacitor AND/OR Diode Bridge Attachment for 202A Cable Tie CapacitorFigure F.10 Field Diode Bridge Location Procedure Field Diode Bridge Removal and ReplacementPowerarc STATOR/ROTOR Removal and Replacement Procedure STATOR/ROTOR Stator Removal ProcedureSection TOC Rotor Removal Procedure Procedure Reactor Bolts Lead WELDER/GENERATOR OUTPUT1 Auxiliary Power Receptacle OUTPUT1Retest After Repair Engine OutputPowerarc Table of Contents Diagram Section Wiring Diagram Codes 11182, 11187, 11329 S25984 Electrical DiagramsSwitch Wiring Diagram Codes 11403, 11405 S26829Wiring Diagram Code 11404 S26830 Wiring Diagram Power ARCWiring Diagram Code 11215 S26023 S26008 Schematic -CODES 11182, 11187, 11329 S26008S26881 Schematic Codes 11403, 11405 S26881S26882 Schematic Code 11404 S26882
Top Page Image Contents