Hitachi C 10FCE instruction manual Switch Laser Line

Page 14

English

*Laser radiation- Do not stare into beam.

*Laser radiation on work table. Do not stare into beam.

If your eye is exposed directly to the laser beam, it can be hurt.

*Do not dismantle it.

*Do not give strong impact to the laser marker (main body of tool); otherwise, the position of a laser line can go out of order, resulting in the damage of the laser marker as well as a shortened service life.

*Keep the laser marker lit only during a cutting operation. Prolonged lighting of the laser marker can result in a shortened service life.

*Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

NOTE: * Perform cutting by overlapping the ink line with the laser line.

*When the ink line and the laser line are overlapped, the strength and weakness of light will change, resulting in a stable cutting operation because you can easily discern the conformity of lines. This ensures the minimum cutting errors.

*In outdoor or near-the-window operations, it may become difficult to observe the laser line due to the sunlight. Under such circumstances, move to a place that is not directly under the sunlight and engage in the operation.

*Do not tug on the cord behind the motor head or hook your finger, wood and the like around it; otherwise, the cord may come off and the laser marker may not be lit up.

Switch

Laser Line

Ink lining can be easily made on this tool to the laser marker. A switch lights up the laser marker. (Fig. 14)

Depending upon your cutting choice, the laser line can be aligned with the left side of the cutting width (saw blade) or the ink line on the right side.

The laser line is adjusted to the width of the saw blade at the time of factory shipment. Adjust the positions of the saw blade and the laser line taking the following steps to suit the use of your choice.

Fig. 14

Workpiece

 

 

Saw Blade

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Marking (pre-marked)

(1)Light up the laser marker and make a groove of about 3/16" (5mm) deep on the workpiece that is about 1-1/2" (38mm) in height and 3-1/2"(89mm) in width. Hold the grooved workpiece by vise as it is and do not move it.

Cutting Width

Fig. 15

Laser Line

Move

Groove

Fig. 16

4mm Hex. Bar Wrench

Turn

(2)Then insert a 4mm hex. bar wrench in the 12 diameter hole on the side of the gear case, turn the hex. socket set screw to move the laser line. (If you turn the Hex. socket screw clockwise, the laser line will shift to the right and if you turn it counterclockwise, the laser line will shift to the left.) When you work with the ink line aligned with the left side of the saw blade, align the laser line with the left end of the groove. (Fig. 16) When you align it with the right side of the saw blade, align the laser line with the right side of the groove.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Avertissement AdvertenciaContents Important Safety Instructions for Using ALL Power Tools Important Safety InformationMeanings of Signal Words Specific Safety Rules for Use of this Power Tool DON’Ts Replacement Parts USE Proper Extension Cord Double Insulation for Safer OperationOperation and Maintenance Name of PartsSpecifications C10FCHPreparation Before Operation InstallationApplications Make sure the power source is appropriate for the tool Before UsingInstalling the dust bag, holder, stopper and vises Releasing the locking pinBefore Cutting Confirmation for use of sub fence …Optional accessory Position adjustment of laser line Only Model C10FCHSwitch Laser Line Switch operation Practical ApplicationsUsing the Vise Assembly Standard accessory Cutting OperationCompound cutting procedures Miter cutting proceduresBevel cutting procedures For bevel cut setting Crown molding cutting proceduresFor miter cut setting Crown molding Stopper L and R optional accessories allow Cutting easily-deformed materials, such as aluminum sash How to use the dust bag Standard accessorySAW Blade Mounting and Dismounting Mounting the saw blade -a, -b, -c and -dInspecting the saw blade Maintenance and InspectionDismounting the saw blade About Handling the Motor see Fig Inspecting the leverInspecting the carbon brushes and Fig Inspecting the screwsLubrication Service and RepairsCleaning Consignes DE Securite Relatives AUX Outils Électriques Informations Importantes DE SécuritéSignification DES Mots D’AVERTISSEMENT Français Consignes de sécurité spéciales pour cet outil électrique Français Double Isolation Pour UN Fonctionnement Plus SUR Pieces DE RechangeUtiliser LE Cordon DE Rallonge Approprié Français Utilisation ET Entretien NOM DES PiècesSpécifications Préparation Avant L’UTILISATION ’assurer que la source d’alimentation convient pour l’outil Avant L’UTILISATIONLibérer la goupille de verrouillage Vérifier que la gâchette est sur OFFAvant LA Coupe Une coupe stable du matériau avec une face arrière large Remarques Applications Pratiques Fonctionnement de l’interrupteurUtilisation de l’ensemble d’étau Accessoire standard CoupeProcédures de coupe mixte Procédure de coupe d’ongletProcédure de coupe de biseau Réglage d’une coupe de biseau Procédures de coupe de corniche complexeRéglage d’une coupe d’onglet ’étau B de corniche complexe accessoire en option peut Installation ET Retrait DE LA Lame Utilisation du sac à copeaux Accessoire standardInstallation de la lame -a, -b, -c et -d Retrait de la lameEntretien ET Inspection Graissage Service APRÈS-VENTE ET RéparationsRemisage NettoyageNormas DE Seguridad Para LAS Herramientas Eléctricas Información Importante Sobre SeguridadSignificado DE LAS Palabras DE Señalización Español Español Español Piezas DE Reemplazo Utilice EL Cable Prolongador Adecuado Aislamiento Doble Para Ofrecer UNA Operación MÁS SeguraOperación Y Mantenimiento Nomenclatura DE PartesEspecificaciones Mesa giratoria Dimensión máxima de corte Máxima IngletesInstalación AplicacionesPreparativos Previos a LA Operación Cerciórese de que el interruptor de disparo esté en OFF Antes DE LA UtilizaciónLiberación del pasador de bloqueo Compruebe si la hoja de sierra posee defectos visiblesAntes DEL Corte Posición de ajuste de la línea de láser Sólo modelo C10FCH Mm, como se muestra en la FigContinuación introduzca una llave de barra hexagonal de Aplicaciones Prácticas Operación de conmutaciónOperación de corte Procedimientos de corte compuesto Procedimiento de corte de ingletesProcedimientos de corte de ingletes Para el ajuste del corte en bisel Procedimientos de corte con moldura en vérticePara el ajuste de corte de ingletes Se muestra en la -a. Después de la in sercion, apriete el Forma de utilizar la bolsa para el polvo Accesorio estándar Una posición en que no haga contacto con la hoja de sierraMontaje Y Desmontaje DE LA Hoja DE Sierra Montaje de la hoja de sierra -a, -b, -c y -dInspección de la hoja de sierra Mantenimiento E InspecciónDesmontaje de la hoja de sierra Inspección de la palancaServicio Y Reparaciones Page Page Page Page Page Page Page Page Hitachi Koki Canada Co

C 10FCE specifications

The Hitachi C 10FCE is a powerful and versatile 10-inch sliding compound miter saw designed to meet the needs of both professional contractors and serious DIY enthusiasts. Renowned for its precision and ease of use, this tool is engineered to deliver accurate cuts while offering a range of features that enhance its functionality.

One of the standout features of the C 10FCE is its 15-amp motor, which delivers a robust performance capable of cutting through a variety of materials, including hardwoods, softwoods, and engineered woods. The motor provides a no-load speed of 5,000 RPM, allowing for swift and efficient cutting tasks. The saw is equipped with a unique 0 to 52-degree miter angle range, providing versatility for making precise crosscuts at various angles. The dual-bevel functionality allows users to make beveled cuts in both directions, amplifying the tool’s adaptability for a wide range of projects.

The C 10FCE is also equipped with a laser guide system, which aids in ensuring accuracy by projecting a line on the workpiece where the cut will occur. This feature is particularly useful for achieving clean and precise cuts, reducing the likelihood of errors. Additionally, the saw boasts a large, robust table that provides ample support for larger workpieces, enhancing stability during use.

Durability is an important characteristic of the Hitachi C 10FCE. The saw features a rigid base that minimizes vibration and maximizes stability, resulting in smoother operation. The model is constructed with high-quality materials, ensuring longevity and consistent performance over time.

Safety is another key aspect integrated into the C 10FCE design. The saw includes a blade guard that covers the upper portion of the blade while in operation, protecting users from accidental contact. The electric brake system stops the blade quickly after the trigger is released, further enhancing user safety.

In conclusion, the Hitachi C 10FCE sliding compound miter saw is a feature-rich tool combining power, precision, and safety. With its reliable motor, versatile cutting angles, laser guide system, and durable construction, it stands as an ideal choice for anyone looking to tackle complex cutting tasks with confidence and accuracy. Whether for intricate trim work or larger construction projects, the C 10FCE is built to handle a diverse range of applications efficiently.
Top Page Image Contents