Hitachi C 10FCE instruction manual Practical Applications, Switch operation

Page 15

Laser Line

Marking (pre-marked)

English

(3)After adjusting the position of the laser line, draw a right-angle ink line on the workpiece and align the ink line with the laser line. When aligning the ink line, slide the workpiece little by little and secure it by vise at a position where the laser line overlaps with the ink line. Work on the grooving again and check the position of the laser line. If you wish to change the laser line's position, make adjustments again following the steps from

(1) to (3).

Fig. 17

NOTE: Check and make sure on a periodic basis if the position of the laser line is in order. As regards the checking method, draw a right-angle ink line on the workpiece with the height of about 1-1/2" (38mm) and the width of 3-1/2" (89mm), and check that the laser line is in line with the ink line [The deviation between the ink line and the laser line should be less than the ink line width (0.5mm)]. (Fig. 17)

PRACTICAL APPLICATIONS

WARNING: * To avoid personal injury, never remove or place a workpiece on the table while the tool is being operated.

*Never place your limbs inside of the line next to warning sign while the tool is being operated. This may cause hazardous conditions (see Fig. 18).

 

Warning Sign

 

Line

Warning Sign

Line

 

 

1. Switch operation

Hole

Trigger

Switch

Fig. 18

Pull the trigger to turn on the switch, release it to shut it off. After releasing the trigger, make sure the trigger has gone all the way back and the switch is turned off.

Fig. 19

WARNING: This will ensure that the power tool cannot be turned on accidentally or by someone (especially a child) who is not qualified to use the power tool.

To prevent unauthorized operation of this tool, insert a padlock through the hole in the switch trigger.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Advertencia AvertissementContents Important Safety Information Meanings of Signal WordsImportant Safety Instructions for Using ALL Power Tools Specific Safety Rules for Use of this Power Tool DON’Ts Replacement Parts Double Insulation for Safer Operation USE Proper Extension CordName of Parts Operation and MaintenanceC10FCH SpecificationsInstallation ApplicationsPreparation Before Operation Releasing the locking pin Before UsingInstalling the dust bag, holder, stopper and vises Make sure the power source is appropriate for the toolBefore Cutting Position adjustment of laser line Only Model C10FCH Confirmation for use of sub fence …Optional accessorySwitch Laser Line Practical Applications Switch operationCutting Operation Using the Vise Assembly Standard accessoryMiter cutting procedures Bevel cutting proceduresCompound cutting procedures Crown molding cutting procedures For miter cut settingFor bevel cut setting Crown molding Stopper L and R optional accessories allow Mounting the saw blade -a, -b, -c and -d How to use the dust bag Standard accessorySAW Blade Mounting and Dismounting Cutting easily-deformed materials, such as aluminum sashMaintenance and Inspection Dismounting the saw bladeInspecting the saw blade Inspecting the screws Inspecting the leverInspecting the carbon brushes and Fig About Handling the Motor see FigService and Repairs CleaningLubrication Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTConsignes DE Securite Relatives AUX Outils Électriques Français Consignes de sécurité spéciales pour cet outil électrique Français Pieces DE Rechange Utiliser LE Cordon DE Rallonge AppropriéDouble Isolation Pour UN Fonctionnement Plus SUR Français NOM DES Pièces Utilisation ET EntretienSpécifications Préparation Avant L’UTILISATION Vérifier que la gâchette est sur OFF Avant L’UTILISATIONLibérer la goupille de verrouillage ’assurer que la source d’alimentation convient pour l’outilAvant LA Coupe Une coupe stable du matériau avec une face arrière large Remarques Fonctionnement de l’interrupteur Applications PratiquesCoupe Utilisation de l’ensemble d’étau Accessoire standardProcédure de coupe d’onglet Procédure de coupe de biseauProcédures de coupe mixte Procédures de coupe de corniche complexe Réglage d’une coupe d’ongletRéglage d’une coupe de biseau ’étau B de corniche complexe accessoire en option peut Utilisation du sac à copeaux Accessoire standard Installation ET Retrait DE LA LameRetrait de la lame Installation de la lame -a, -b, -c et -dEntretien ET Inspection Nettoyage Service APRÈS-VENTE ET RéparationsRemisage GraissageInformación Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónNormas DE Seguridad Para LAS Herramientas Eléctricas Español Español Español Piezas DE Reemplazo Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Utilice EL Cable Prolongador AdecuadoNomenclatura DE Partes Operación Y MantenimientoMesa giratoria Dimensión máxima de corte Máxima Ingletes EspecificacionesAplicaciones Preparativos Previos a LA OperaciónInstalación Compruebe si la hoja de sierra posee defectos visibles Antes DE LA UtilizaciónLiberación del pasador de bloqueo Cerciórese de que el interruptor de disparo esté en OFFAntes DEL Corte Mm, como se muestra en la Fig Posición de ajuste de la línea de láser Sólo modelo C10FCHContinuación introduzca una llave de barra hexagonal de Operación de conmutación Aplicaciones PrácticasOperación de corte Procedimiento de corte de ingletes Procedimientos de corte de ingletesProcedimientos de corte compuesto Procedimientos de corte con moldura en vértice Para el ajuste de corte de ingletesPara el ajuste del corte en bisel Se muestra en la -a. Después de la in sercion, apriete el Una posición en que no haga contacto con la hoja de sierra Forma de utilizar la bolsa para el polvo Accesorio estándarMontaje de la hoja de sierra -a, -b, -c y -d Montaje Y Desmontaje DE LA Hoja DE SierraInspección de la palanca Mantenimiento E InspecciónDesmontaje de la hoja de sierra Inspección de la hoja de sierraServicio Y Reparaciones Page Page Page Page Page Page Page Page Hitachi Koki Canada Co

C 10FCE specifications

The Hitachi C 10FCE is a powerful and versatile 10-inch sliding compound miter saw designed to meet the needs of both professional contractors and serious DIY enthusiasts. Renowned for its precision and ease of use, this tool is engineered to deliver accurate cuts while offering a range of features that enhance its functionality.

One of the standout features of the C 10FCE is its 15-amp motor, which delivers a robust performance capable of cutting through a variety of materials, including hardwoods, softwoods, and engineered woods. The motor provides a no-load speed of 5,000 RPM, allowing for swift and efficient cutting tasks. The saw is equipped with a unique 0 to 52-degree miter angle range, providing versatility for making precise crosscuts at various angles. The dual-bevel functionality allows users to make beveled cuts in both directions, amplifying the tool’s adaptability for a wide range of projects.

The C 10FCE is also equipped with a laser guide system, which aids in ensuring accuracy by projecting a line on the workpiece where the cut will occur. This feature is particularly useful for achieving clean and precise cuts, reducing the likelihood of errors. Additionally, the saw boasts a large, robust table that provides ample support for larger workpieces, enhancing stability during use.

Durability is an important characteristic of the Hitachi C 10FCE. The saw features a rigid base that minimizes vibration and maximizes stability, resulting in smoother operation. The model is constructed with high-quality materials, ensuring longevity and consistent performance over time.

Safety is another key aspect integrated into the C 10FCE design. The saw includes a blade guard that covers the upper portion of the blade while in operation, protecting users from accidental contact. The electric brake system stops the blade quickly after the trigger is released, further enhancing user safety.

In conclusion, the Hitachi C 10FCE sliding compound miter saw is a feature-rich tool combining power, precision, and safety. With its reliable motor, versatile cutting angles, laser guide system, and durable construction, it stands as an ideal choice for anyone looking to tackle complex cutting tasks with confidence and accuracy. Whether for intricate trim work or larger construction projects, the C 10FCE is built to handle a diverse range of applications efficiently.
Top Page Image Contents