Hitachi C 10FCE Inspecting the lever, Inspecting the carbon brushes and Fig, Storage

Page 22
Groove for Driver

English

2. Inspecting the lever

If the M6 hexagonal head bolts (2) are loose, align the sides of the fence and saw blade with the steel square. After adjusting the saw blade and fence to a ninety-degree angle, tighten the lever securing hexagonal head bolts (2).

Lever

Saw Blade

Fence

Hex. Head Bolt

Steel Square

Fig. 34-a

Fig. 34-b

3. Inspecting the carbon brushes (Fig. 35 and Fig. 36)

The carbon brushes in the motor are expendable parts.

If the carbon brushes become excessively worn, motor trouble might occur.

Therefore, inspect the carbon brushes periodically and replace them when they have become worn to the wear limit line as shown in Fig. 35.

Also, keep the carbon brushes clean so that they will slide smoothly within the brush holders.

The carbon brushes can easily be removed after removal of the brush caps (see Fig. 36) with a slotted (minus) screwdriver.

Wear Limit Line

38

1/4" (6mm)

11/16" (17mm)

No. 38 indicates the last

Brush Cap

 

two numbers of carbon

 

brush Code No.

Fig. 35

Fig. 36

4. About Handling the Motor (see Fig. 1)

Winding of the motor is said to be the heart of this tool. Exercise utmost caution not to damage the winding by exposing it to wash oil or water.

NOTE: Accumulation of dust and the like inside the motor can result in a malfunction.

After using the motor for 50 hours or so, carry out no-load running, and blow in the dry air from a wind hole at the motor's rear. Such action is effective to discharge dust and the like.

5. Inspecting the screws

Regularly inspect each component of the power tool for looseness.

Re-tighten screws on any loose part.

WARNING: To prevent personal injury, never operate the power tool if any components are loose.

6. Inspecting the lower guard for proper operation

Before each use of the tool, test the lower guard (see Fig. 7) to assure that it is in good condition and that it moves smoothly.

Never use the tool unless the lower guard operates properly and it is in good mechanical condition.

7. Storage

After operation of the tool has been completed, check that the following has been performed:

(1)Trigger switch is in OFF position,

(2)Power plug has been removed from the receptacle,

(3)Lock-off button has been removed and stored in a secure place.

When the tool is not in use, keep it stored in a dry place out of the reach of children.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Avertissement AdvertenciaContents Meanings of Signal Words Important Safety InformationImportant Safety Instructions for Using ALL Power Tools Specific Safety Rules for Use of this Power Tool DON’Ts Replacement Parts USE Proper Extension Cord Double Insulation for Safer OperationOperation and Maintenance Name of PartsSpecifications C10FCHApplications InstallationPreparation Before Operation Make sure the power source is appropriate for the tool Before UsingInstalling the dust bag, holder, stopper and vises Releasing the locking pinBefore Cutting Confirmation for use of sub fence …Optional accessory Position adjustment of laser line Only Model C10FCHSwitch Laser Line Switch operation Practical ApplicationsUsing the Vise Assembly Standard accessory Cutting OperationBevel cutting procedures Miter cutting proceduresCompound cutting procedures For miter cut setting Crown molding cutting proceduresFor bevel cut setting Crown molding Stopper L and R optional accessories allow Cutting easily-deformed materials, such as aluminum sash How to use the dust bag Standard accessorySAW Blade Mounting and Dismounting Mounting the saw blade -a, -b, -c and -dDismounting the saw blade Maintenance and InspectionInspecting the saw blade About Handling the Motor see Fig Inspecting the leverInspecting the carbon brushes and Fig Inspecting the screwsCleaning Service and RepairsLubrication Signification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéConsignes DE Securite Relatives AUX Outils Électriques Français Consignes de sécurité spéciales pour cet outil électrique Français Utiliser LE Cordon DE Rallonge Approprié Pieces DE RechangeDouble Isolation Pour UN Fonctionnement Plus SUR Français Utilisation ET Entretien NOM DES PiècesSpécifications Préparation Avant L’UTILISATION ’assurer que la source d’alimentation convient pour l’outil Avant L’UTILISATIONLibérer la goupille de verrouillage Vérifier que la gâchette est sur OFFAvant LA Coupe Une coupe stable du matériau avec une face arrière large Remarques Applications Pratiques Fonctionnement de l’interrupteurUtilisation de l’ensemble d’étau Accessoire standard CoupeProcédure de coupe de biseau Procédure de coupe d’ongletProcédures de coupe mixte Réglage d’une coupe d’onglet Procédures de coupe de corniche complexeRéglage d’une coupe de biseau ’étau B de corniche complexe accessoire en option peut Installation ET Retrait DE LA Lame Utilisation du sac à copeaux Accessoire standardInstallation de la lame -a, -b, -c et -d Retrait de la lameEntretien ET Inspection Graissage Service APRÈS-VENTE ET RéparationsRemisage NettoyageSignificado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadNormas DE Seguridad Para LAS Herramientas Eléctricas Español Español Español Piezas DE Reemplazo Utilice EL Cable Prolongador Adecuado Aislamiento Doble Para Ofrecer UNA Operación MÁS SeguraOperación Y Mantenimiento Nomenclatura DE PartesEspecificaciones Mesa giratoria Dimensión máxima de corte Máxima IngletesPreparativos Previos a LA Operación AplicacionesInstalación Cerciórese de que el interruptor de disparo esté en OFF Antes DE LA UtilizaciónLiberación del pasador de bloqueo Compruebe si la hoja de sierra posee defectos visiblesAntes DEL Corte Posición de ajuste de la línea de láser Sólo modelo C10FCH Mm, como se muestra en la FigContinuación introduzca una llave de barra hexagonal de Aplicaciones Prácticas Operación de conmutaciónOperación de corte Procedimientos de corte de ingletes Procedimiento de corte de ingletesProcedimientos de corte compuesto Para el ajuste de corte de ingletes Procedimientos de corte con moldura en vérticePara el ajuste del corte en bisel Se muestra en la -a. Después de la in sercion, apriete el Forma de utilizar la bolsa para el polvo Accesorio estándar Una posición en que no haga contacto con la hoja de sierraMontaje Y Desmontaje DE LA Hoja DE Sierra Montaje de la hoja de sierra -a, -b, -c y -dInspección de la hoja de sierra Mantenimiento E InspecciónDesmontaje de la hoja de sierra Inspección de la palancaServicio Y Reparaciones Page Page Page Page Page Page Page Page Hitachi Koki Canada Co

C 10FCE specifications

The Hitachi C 10FCE is a powerful and versatile 10-inch sliding compound miter saw designed to meet the needs of both professional contractors and serious DIY enthusiasts. Renowned for its precision and ease of use, this tool is engineered to deliver accurate cuts while offering a range of features that enhance its functionality.

One of the standout features of the C 10FCE is its 15-amp motor, which delivers a robust performance capable of cutting through a variety of materials, including hardwoods, softwoods, and engineered woods. The motor provides a no-load speed of 5,000 RPM, allowing for swift and efficient cutting tasks. The saw is equipped with a unique 0 to 52-degree miter angle range, providing versatility for making precise crosscuts at various angles. The dual-bevel functionality allows users to make beveled cuts in both directions, amplifying the tool’s adaptability for a wide range of projects.

The C 10FCE is also equipped with a laser guide system, which aids in ensuring accuracy by projecting a line on the workpiece where the cut will occur. This feature is particularly useful for achieving clean and precise cuts, reducing the likelihood of errors. Additionally, the saw boasts a large, robust table that provides ample support for larger workpieces, enhancing stability during use.

Durability is an important characteristic of the Hitachi C 10FCE. The saw features a rigid base that minimizes vibration and maximizes stability, resulting in smoother operation. The model is constructed with high-quality materials, ensuring longevity and consistent performance over time.

Safety is another key aspect integrated into the C 10FCE design. The saw includes a blade guard that covers the upper portion of the blade while in operation, protecting users from accidental contact. The electric brake system stops the blade quickly after the trigger is released, further enhancing user safety.

In conclusion, the Hitachi C 10FCE sliding compound miter saw is a feature-rich tool combining power, precision, and safety. With its reliable motor, versatile cutting angles, laser guide system, and durable construction, it stands as an ideal choice for anyone looking to tackle complex cutting tasks with confidence and accuracy. Whether for intricate trim work or larger construction projects, the C 10FCE is built to handle a diverse range of applications efficiently.
Top Page Image Contents