Hitachi C 10FCE Miter cutting procedures, Bevel cutting procedures, Compound cutting procedures

Page 17

English

4. Miter cutting procedures

 

Turntable

Miter Scale

Indicator

(For miter scale)

Turn the

Lever

turntable

Push

Loosen

Tighten

 

Side Handle

(1)Loosen the side handle and push the lever for angle stoppers. Then, adjust the turntable until the indicator aligns with desired setting on the miter scale (Fig. 22).

(2)Re-tighten the side handle to secure the turntable in the desired position.

NOTE: * Positive stops are provided at the right and left of the 0° center setting, at 15°, 22.5°, 31.6° and 45° settings. Check that the miter scale and the tip of the indicator are properly aligned.

*Operation of the saw with the miter scale and indicator out of alignment, or with the side handle not properly tightened, will result in poor cutting precision.

Fig. 22

CAUTION: Never remove the side handle; use of the tool without it would be hazardous. To prevent an accident or personal injury always firmly tighten the miter handle.

5. Bevel cutting procedures

(1) Loosen the clamp lever and bevel the saw blade to the left.

(2) Adjust the bevel angle to the desired setting while watching the bevel angle scale and indicator, then secure the clamp lever.

Indicator

(for bevel scale)

Clamp Lever

Tighten

Loosen

Fig. 23

WARNING: When the workpiece is secured on the left or right side of the blade, the short cut-off portion will come to rest on the right or left side of the saw blade. Always turn the power off and let the saw blade stop completely before raising the handle from the workpiece.

If the handle is raised while the saw blade is still rotating, the cut-off piece may become jammed against the saw blade causing fragments to scatter about dangerously.

When stopping the bevel cutting operation halfway, start cutting after pulling back the motor head to the initial position.

Starting from halfway, without pulling back, causes the safety cover to be caught in the cutting groove of the workpiece and to contact the saw blade.

6. Compound cutting procedures

Compound cutting can be performed by following the instructions in 4 and 5 above. For maximum dimensions for compound cutting, refer to “SPECIFICATIONS” table on page 9.

CAUTION: Always secure the workpiece with the right hand side for compound cutting. Never rotate the table to the right for compound cutting, because the saw blade might then contact the clamp or vise that secures the workpiece, and cause personal injury or damage.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Advertencia AvertissementContents Important Safety Instructions for Using ALL Power Tools Important Safety InformationMeanings of Signal Words Specific Safety Rules for Use of this Power Tool DON’Ts Replacement Parts Double Insulation for Safer Operation USE Proper Extension CordName of Parts Operation and MaintenanceC10FCH SpecificationsPreparation Before Operation InstallationApplications Installing the dust bag, holder, stopper and vises Before UsingMake sure the power source is appropriate for the tool Releasing the locking pinBefore Cutting Position adjustment of laser line Only Model C10FCH Confirmation for use of sub fence …Optional accessorySwitch Laser Line Practical Applications Switch operationCutting Operation Using the Vise Assembly Standard accessoryCompound cutting procedures Miter cutting proceduresBevel cutting procedures For bevel cut setting Crown molding cutting proceduresFor miter cut setting Crown molding Stopper L and R optional accessories allow SAW Blade Mounting and Dismounting How to use the dust bag Standard accessoryCutting easily-deformed materials, such as aluminum sash Mounting the saw blade -a, -b, -c and -dInspecting the saw blade Maintenance and InspectionDismounting the saw blade Inspecting the carbon brushes and Fig Inspecting the leverAbout Handling the Motor see Fig Inspecting the screwsLubrication Service and RepairsCleaning Consignes DE Securite Relatives AUX Outils Électriques Informations Importantes DE SécuritéSignification DES Mots D’AVERTISSEMENT Français Consignes de sécurité spéciales pour cet outil électrique Français Double Isolation Pour UN Fonctionnement Plus SUR Pieces DE RechangeUtiliser LE Cordon DE Rallonge Approprié Français NOM DES Pièces Utilisation ET EntretienSpécifications Préparation Avant L’UTILISATION Libérer la goupille de verrouillage Avant L’UTILISATION’assurer que la source d’alimentation convient pour l’outil Vérifier que la gâchette est sur OFFAvant LA Coupe Une coupe stable du matériau avec une face arrière large Remarques Fonctionnement de l’interrupteur Applications PratiquesCoupe Utilisation de l’ensemble d’étau Accessoire standardProcédures de coupe mixte Procédure de coupe d’ongletProcédure de coupe de biseau Réglage d’une coupe de biseau Procédures de coupe de corniche complexeRéglage d’une coupe d’onglet ’étau B de corniche complexe accessoire en option peut Utilisation du sac à copeaux Accessoire standard Installation ET Retrait DE LA LameRetrait de la lame Installation de la lame -a, -b, -c et -dEntretien ET Inspection Remisage Service APRÈS-VENTE ET RéparationsGraissage NettoyageNormas DE Seguridad Para LAS Herramientas Eléctricas Información Importante Sobre SeguridadSignificado DE LAS Palabras DE Señalización Español Español Español Piezas DE Reemplazo Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Utilice EL Cable Prolongador AdecuadoNomenclatura DE Partes Operación Y MantenimientoMesa giratoria Dimensión máxima de corte Máxima Ingletes EspecificacionesInstalación AplicacionesPreparativos Previos a LA Operación Liberación del pasador de bloqueo Antes DE LA UtilizaciónCerciórese de que el interruptor de disparo esté en OFF Compruebe si la hoja de sierra posee defectos visiblesAntes DEL Corte Mm, como se muestra en la Fig Posición de ajuste de la línea de láser Sólo modelo C10FCHContinuación introduzca una llave de barra hexagonal de Operación de conmutación Aplicaciones PrácticasOperación de corte Procedimientos de corte compuesto Procedimiento de corte de ingletesProcedimientos de corte de ingletes Para el ajuste del corte en bisel Procedimientos de corte con moldura en vérticePara el ajuste de corte de ingletes Se muestra en la -a. Después de la in sercion, apriete el Una posición en que no haga contacto con la hoja de sierra Forma de utilizar la bolsa para el polvo Accesorio estándarMontaje de la hoja de sierra -a, -b, -c y -d Montaje Y Desmontaje DE LA Hoja DE SierraDesmontaje de la hoja de sierra Mantenimiento E InspecciónInspección de la hoja de sierra Inspección de la palancaServicio Y Reparaciones Page Page Page Page Page Page Page Page Hitachi Koki Canada Co

C 10FCE specifications

The Hitachi C 10FCE is a powerful and versatile 10-inch sliding compound miter saw designed to meet the needs of both professional contractors and serious DIY enthusiasts. Renowned for its precision and ease of use, this tool is engineered to deliver accurate cuts while offering a range of features that enhance its functionality.

One of the standout features of the C 10FCE is its 15-amp motor, which delivers a robust performance capable of cutting through a variety of materials, including hardwoods, softwoods, and engineered woods. The motor provides a no-load speed of 5,000 RPM, allowing for swift and efficient cutting tasks. The saw is equipped with a unique 0 to 52-degree miter angle range, providing versatility for making precise crosscuts at various angles. The dual-bevel functionality allows users to make beveled cuts in both directions, amplifying the tool’s adaptability for a wide range of projects.

The C 10FCE is also equipped with a laser guide system, which aids in ensuring accuracy by projecting a line on the workpiece where the cut will occur. This feature is particularly useful for achieving clean and precise cuts, reducing the likelihood of errors. Additionally, the saw boasts a large, robust table that provides ample support for larger workpieces, enhancing stability during use.

Durability is an important characteristic of the Hitachi C 10FCE. The saw features a rigid base that minimizes vibration and maximizes stability, resulting in smoother operation. The model is constructed with high-quality materials, ensuring longevity and consistent performance over time.

Safety is another key aspect integrated into the C 10FCE design. The saw includes a blade guard that covers the upper portion of the blade while in operation, protecting users from accidental contact. The electric brake system stops the blade quickly after the trigger is released, further enhancing user safety.

In conclusion, the Hitachi C 10FCE sliding compound miter saw is a feature-rich tool combining power, precision, and safety. With its reliable motor, versatile cutting angles, laser guide system, and durable construction, it stands as an ideal choice for anyone looking to tackle complex cutting tasks with confidence and accuracy. Whether for intricate trim work or larger construction projects, the C 10FCE is built to handle a diverse range of applications efficiently.
Top Page Image Contents