Hitachi C 10FCE USE Proper Extension Cord, Double Insulation for Safer Operation

Page 7

English

USE PROPER EXTENSION CORD

Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

MINIMUM GAGE FOR CORD SETS

 

 

 

Total Length of Cord in Feet (Meter)

 

 

 

 

0 – 25

26 – 50

51 – 100

101 – 150

 

 

 

(0 – 7.6)

(7.9 – 15.2)

(15.5 – 30.5)

(30.8 – 45.7)

Ampere Rating

 

AWG

 

 

More

Not More

 

 

 

 

Than

 

Than

 

 

 

 

0

– 6

18

16

16

14

6

– 10

18

16

14

12

10

– 12

16

16

14

12

12

– 16

14

12

Not Recommended

WARNING: Avoid electrical shock hazard. Never use this tool with a damaged or frayed electrical cord or extension cord.

Inspect all electrical cords regularly. Never use in or near water or in any environment where electric shock is possible.

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation design. “Double insulation” means that two physically separated insulation systems have been used to insulate the electrically conductive materials connected to the power supply from the outer frame handled by the operator. Therefore, either the symbol “ ” or the words and “Double insulation” appear on the power tool or on the nameplate. Although this system has no external grounding, you must still follow the normal electrical safety precautions given in this Instruction Manual, including not using the power tool in wet environments.

To keep the double insulation system effective, follow these precautions:

*Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this power tool, and only genuine HITACHI replacement parts should be installed.

*Clean the exterior of the power tool only with a soft cloth moistened with soapy water and dry thoroughly.

*Never use solvents, gasoline or thinners on plastic components; otherwise the plastic may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

7

Image 7
Contents Advertencia AvertissementContents Meanings of Signal Words Important Safety InformationImportant Safety Instructions for Using ALL Power Tools Specific Safety Rules for Use of this Power Tool DON’Ts Replacement Parts Double Insulation for Safer Operation USE Proper Extension CordName of Parts Operation and MaintenanceC10FCH SpecificationsApplications InstallationPreparation Before Operation Releasing the locking pin Before UsingInstalling the dust bag, holder, stopper and vises Make sure the power source is appropriate for the toolBefore Cutting Position adjustment of laser line Only Model C10FCH Confirmation for use of sub fence …Optional accessorySwitch Laser Line Practical Applications Switch operationCutting Operation Using the Vise Assembly Standard accessoryBevel cutting procedures Miter cutting proceduresCompound cutting procedures For miter cut setting Crown molding cutting proceduresFor bevel cut setting Crown molding Stopper L and R optional accessories allow Mounting the saw blade -a, -b, -c and -d How to use the dust bag Standard accessorySAW Blade Mounting and Dismounting Cutting easily-deformed materials, such as aluminum sashDismounting the saw blade Maintenance and InspectionInspecting the saw blade Inspecting the screws Inspecting the leverInspecting the carbon brushes and Fig About Handling the Motor see FigCleaning Service and RepairsLubrication Signification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéConsignes DE Securite Relatives AUX Outils Électriques Français Consignes de sécurité spéciales pour cet outil électrique Français Utiliser LE Cordon DE Rallonge Approprié Pieces DE RechangeDouble Isolation Pour UN Fonctionnement Plus SUR Français NOM DES Pièces Utilisation ET EntretienSpécifications Préparation Avant L’UTILISATION Vérifier que la gâchette est sur OFF Avant L’UTILISATIONLibérer la goupille de verrouillage ’assurer que la source d’alimentation convient pour l’outilAvant LA Coupe Une coupe stable du matériau avec une face arrière large Remarques Fonctionnement de l’interrupteur Applications PratiquesCoupe Utilisation de l’ensemble d’étau Accessoire standardProcédure de coupe de biseau Procédure de coupe d’ongletProcédures de coupe mixte Réglage d’une coupe d’onglet Procédures de coupe de corniche complexeRéglage d’une coupe de biseau ’étau B de corniche complexe accessoire en option peut Utilisation du sac à copeaux Accessoire standard Installation ET Retrait DE LA LameRetrait de la lame Installation de la lame -a, -b, -c et -dEntretien ET Inspection Nettoyage Service APRÈS-VENTE ET RéparationsRemisage GraissageSignificado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadNormas DE Seguridad Para LAS Herramientas Eléctricas Español Español Español Piezas DE Reemplazo Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Utilice EL Cable Prolongador AdecuadoNomenclatura DE Partes Operación Y MantenimientoMesa giratoria Dimensión máxima de corte Máxima Ingletes EspecificacionesPreparativos Previos a LA Operación AplicacionesInstalación Compruebe si la hoja de sierra posee defectos visibles Antes DE LA UtilizaciónLiberación del pasador de bloqueo Cerciórese de que el interruptor de disparo esté en OFFAntes DEL Corte Mm, como se muestra en la Fig Posición de ajuste de la línea de láser Sólo modelo C10FCHContinuación introduzca una llave de barra hexagonal de Operación de conmutación Aplicaciones PrácticasOperación de corte Procedimientos de corte de ingletes Procedimiento de corte de ingletesProcedimientos de corte compuesto Para el ajuste de corte de ingletes Procedimientos de corte con moldura en vérticePara el ajuste del corte en bisel Se muestra en la -a. Después de la in sercion, apriete el Una posición en que no haga contacto con la hoja de sierra Forma de utilizar la bolsa para el polvo Accesorio estándarMontaje de la hoja de sierra -a, -b, -c y -d Montaje Y Desmontaje DE LA Hoja DE SierraInspección de la palanca Mantenimiento E InspecciónDesmontaje de la hoja de sierra Inspección de la hoja de sierraServicio Y Reparaciones Page Page Page Page Page Page Page Page Hitachi Koki Canada Co

C 10FCE specifications

The Hitachi C 10FCE is a powerful and versatile 10-inch sliding compound miter saw designed to meet the needs of both professional contractors and serious DIY enthusiasts. Renowned for its precision and ease of use, this tool is engineered to deliver accurate cuts while offering a range of features that enhance its functionality.

One of the standout features of the C 10FCE is its 15-amp motor, which delivers a robust performance capable of cutting through a variety of materials, including hardwoods, softwoods, and engineered woods. The motor provides a no-load speed of 5,000 RPM, allowing for swift and efficient cutting tasks. The saw is equipped with a unique 0 to 52-degree miter angle range, providing versatility for making precise crosscuts at various angles. The dual-bevel functionality allows users to make beveled cuts in both directions, amplifying the tool’s adaptability for a wide range of projects.

The C 10FCE is also equipped with a laser guide system, which aids in ensuring accuracy by projecting a line on the workpiece where the cut will occur. This feature is particularly useful for achieving clean and precise cuts, reducing the likelihood of errors. Additionally, the saw boasts a large, robust table that provides ample support for larger workpieces, enhancing stability during use.

Durability is an important characteristic of the Hitachi C 10FCE. The saw features a rigid base that minimizes vibration and maximizes stability, resulting in smoother operation. The model is constructed with high-quality materials, ensuring longevity and consistent performance over time.

Safety is another key aspect integrated into the C 10FCE design. The saw includes a blade guard that covers the upper portion of the blade while in operation, protecting users from accidental contact. The electric brake system stops the blade quickly after the trigger is released, further enhancing user safety.

In conclusion, the Hitachi C 10FCE sliding compound miter saw is a feature-rich tool combining power, precision, and safety. With its reliable motor, versatile cutting angles, laser guide system, and durable construction, it stands as an ideal choice for anyone looking to tackle complex cutting tasks with confidence and accuracy. Whether for intricate trim work or larger construction projects, the C 10FCE is built to handle a diverse range of applications efficiently.