Hitachi C 10FCE instruction manual Crown molding Stopper L and R optional accessories allow

Page 19

English

Head

Head

Bevel Angle Scale

Bevel Angle Scale

4

3

1

2

Fence

Fence

 

 

Base

Miter Angle Scale

Turntable

Base

 

Turntable

Miter Angle Scale

Fig. 26

Fig. 27

Fence

Fence

Table on Base

Table on Base

Fig. 28

Fig. 29

Cutting method of crown molding without tilting the saw blade.

Crown Molding Vise Ass’y (Optional accessories)

6mm Wing Bolt

6mm Wing Bolt

Crown Molding

(1)

Crown molding Stopper (L) and (R) (optional accessories) allow

Stopper (R)

6mm Wing (Optional accessories)

easier cuts of crown molding without tilting the saw blade.

Bolt

 

Install them in the base both-sides side to be shown in Fig. 30-

 

 

 

 

a. After inserting Tighten the 6mm knob bolts to secure the

 

 

crown molding Stoppers.

 

 

[Optional accessories used]

 

 

• Crown molding Vise Ass’y (Include Crown molding Stopper

 

 

(L))

Crown Molding Stopper (L)

 

• Crown molding Stopper (L)

 

• Crown molding Stopper (R)

(Optional accessories)

 

Fig. 30-a

Crown Molding Vise Ass’y (Optional accessories)

6mm Knob Bolt

Knob

Fence

6mm Wing Bolt Crown Molding

(2)The crown molding vise (B) (Optional accessory) can be mounted on either the left fence (Fence (B)) or the right fence (Fence (A)). It can unite with the slope of the crown molding and vice can be pressed down.

Then turn the upper knob, as necessary, to securely attach the crown molding in position. To raise or lower the vise assembly, first loosen the 6mm knob bolt.

After adjusting the height, firmly tighten the 6mm wing bolt; then turn the upper knob, as necessary, to securely attach the crown molding in position. (See Fig. 30-b)

Crown Molding Stopper (L) Crown Molding Stopper (R) (Optional accessories)

Fig. 30-b

WARNING: Always firmly clamp or vise to secure the crown molding to the fence; otherwise the crown molding might be thrust from the table and cause bodily harm.

Do not bevel cutting. The main body or saw blade may contact the sub fence, resulting in an injury.

CAUTION: Always confirm that the motor head (see Fig. 1) does not contact the crown molding vise ass’y when it is lowered for cutting. If there is any danger that it may do so, loosen the 6mm knob bolt and move the crown molding vise ass’y to a position where it will not contact the saw blade.

Position crown molding with its WALL CONTACT EDGE against the guide fence and its CEILING CONTACT EDGE against the crown molding Stoppers as shown in Fig. 30-b.

Adjust the crown molding Stoppers according to the size of the crown molding. Tighten the 6mm wing bolt to secure the crown molding Stoppers.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Advertencia AvertissementContents Meanings of Signal Words Important Safety InformationImportant Safety Instructions for Using ALL Power Tools Specific Safety Rules for Use of this Power Tool DON’Ts Replacement Parts Double Insulation for Safer Operation USE Proper Extension CordName of Parts Operation and MaintenanceC10FCH SpecificationsApplications InstallationPreparation Before Operation Releasing the locking pin Before UsingInstalling the dust bag, holder, stopper and vises Make sure the power source is appropriate for the toolBefore Cutting Position adjustment of laser line Only Model C10FCH Confirmation for use of sub fence …Optional accessorySwitch Laser Line Practical Applications Switch operationCutting Operation Using the Vise Assembly Standard accessoryBevel cutting procedures Miter cutting proceduresCompound cutting procedures For miter cut setting Crown molding cutting proceduresFor bevel cut setting Crown molding Stopper L and R optional accessories allow Mounting the saw blade -a, -b, -c and -d How to use the dust bag Standard accessorySAW Blade Mounting and Dismounting Cutting easily-deformed materials, such as aluminum sashDismounting the saw blade Maintenance and InspectionInspecting the saw blade Inspecting the screws Inspecting the leverInspecting the carbon brushes and Fig About Handling the Motor see FigCleaning Service and RepairsLubrication Signification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéConsignes DE Securite Relatives AUX Outils Électriques Français Consignes de sécurité spéciales pour cet outil électrique Français Utiliser LE Cordon DE Rallonge Approprié Pieces DE RechangeDouble Isolation Pour UN Fonctionnement Plus SUR Français NOM DES Pièces Utilisation ET EntretienSpécifications Préparation Avant L’UTILISATION Vérifier que la gâchette est sur OFF Avant L’UTILISATIONLibérer la goupille de verrouillage ’assurer que la source d’alimentation convient pour l’outilAvant LA Coupe Une coupe stable du matériau avec une face arrière large Remarques Fonctionnement de l’interrupteur Applications PratiquesCoupe Utilisation de l’ensemble d’étau Accessoire standardProcédure de coupe de biseau Procédure de coupe d’ongletProcédures de coupe mixte Réglage d’une coupe d’onglet Procédures de coupe de corniche complexeRéglage d’une coupe de biseau ’étau B de corniche complexe accessoire en option peut Utilisation du sac à copeaux Accessoire standard Installation ET Retrait DE LA LameRetrait de la lame Installation de la lame -a, -b, -c et -dEntretien ET Inspection Nettoyage Service APRÈS-VENTE ET RéparationsRemisage GraissageSignificado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadNormas DE Seguridad Para LAS Herramientas Eléctricas Español Español Español Piezas DE Reemplazo Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Utilice EL Cable Prolongador AdecuadoNomenclatura DE Partes Operación Y MantenimientoMesa giratoria Dimensión máxima de corte Máxima Ingletes EspecificacionesPreparativos Previos a LA Operación AplicacionesInstalación Compruebe si la hoja de sierra posee defectos visibles Antes DE LA UtilizaciónLiberación del pasador de bloqueo Cerciórese de que el interruptor de disparo esté en OFFAntes DEL Corte Mm, como se muestra en la Fig Posición de ajuste de la línea de láser Sólo modelo C10FCHContinuación introduzca una llave de barra hexagonal de Operación de conmutación Aplicaciones PrácticasOperación de corte Procedimientos de corte de ingletes Procedimiento de corte de ingletesProcedimientos de corte compuesto Para el ajuste de corte de ingletes Procedimientos de corte con moldura en vérticePara el ajuste del corte en bisel Se muestra en la -a. Después de la in sercion, apriete el Una posición en que no haga contacto con la hoja de sierra Forma de utilizar la bolsa para el polvo Accesorio estándarMontaje de la hoja de sierra -a, -b, -c y -d Montaje Y Desmontaje DE LA Hoja DE SierraInspección de la palanca Mantenimiento E InspecciónDesmontaje de la hoja de sierra Inspección de la hoja de sierraServicio Y Reparaciones Page Page Page Page Page Page Page Page Hitachi Koki Canada Co

C 10FCE specifications

The Hitachi C 10FCE is a powerful and versatile 10-inch sliding compound miter saw designed to meet the needs of both professional contractors and serious DIY enthusiasts. Renowned for its precision and ease of use, this tool is engineered to deliver accurate cuts while offering a range of features that enhance its functionality.

One of the standout features of the C 10FCE is its 15-amp motor, which delivers a robust performance capable of cutting through a variety of materials, including hardwoods, softwoods, and engineered woods. The motor provides a no-load speed of 5,000 RPM, allowing for swift and efficient cutting tasks. The saw is equipped with a unique 0 to 52-degree miter angle range, providing versatility for making precise crosscuts at various angles. The dual-bevel functionality allows users to make beveled cuts in both directions, amplifying the tool’s adaptability for a wide range of projects.

The C 10FCE is also equipped with a laser guide system, which aids in ensuring accuracy by projecting a line on the workpiece where the cut will occur. This feature is particularly useful for achieving clean and precise cuts, reducing the likelihood of errors. Additionally, the saw boasts a large, robust table that provides ample support for larger workpieces, enhancing stability during use.

Durability is an important characteristic of the Hitachi C 10FCE. The saw features a rigid base that minimizes vibration and maximizes stability, resulting in smoother operation. The model is constructed with high-quality materials, ensuring longevity and consistent performance over time.

Safety is another key aspect integrated into the C 10FCE design. The saw includes a blade guard that covers the upper portion of the blade while in operation, protecting users from accidental contact. The electric brake system stops the blade quickly after the trigger is released, further enhancing user safety.

In conclusion, the Hitachi C 10FCE sliding compound miter saw is a feature-rich tool combining power, precision, and safety. With its reliable motor, versatile cutting angles, laser guide system, and durable construction, it stands as an ideal choice for anyone looking to tackle complex cutting tasks with confidence and accuracy. Whether for intricate trim work or larger construction projects, the C 10FCE is built to handle a diverse range of applications efficiently.
Top Page Image Contents