Hitachi C 10FCE instruction manual Before Cutting

Page 12

English

7. Check the Power Receptacle.

To prevent overheating, accidental stopping or intermittent operation, confirm that the power cord plug fits properly in the electrical receptacle and does not fall out after it is inserted. Repair or replace the receptacle if it is faulty.

8. Confirm the tool’s power cord is not damaged.

Repair or replace the power cord if an inspection indicates that it is damaged.

AFTER CONNECTING THE POWER PLUG TO AN APPROPRIATE AC POWER SOURCE, CHECK THE OPERATION OF THE TOOL AS FOLLOWS:

9. Trial Run

After confirming that no one is standing behind, the power tool start and confirm that no operating abnormalities exist before attempting a cutting operation.

10. Inspect the rotating stability of the saw blade.

For precise cutting, rotate the saw blade and check for deflection to confirm that the blade is not noticeably unstable; otherwise vibrations might occur and cause an accident.

BEFORE CUTTING

1. Oblique angle

Before the power tool is shipped from the factory, it is adjusted for 0°, left 45° bevel cutting angle with the 8mm bolt (A) and the 8mm bolt (B).

When changing the adjustment, change the height of the 8mm bolt (A) or the 8mm bolt (B) by turning them. (Fig. 8-a, Fig. 8-b)

Indicator

(For bevel scale)

8mm Bolt (B) (Stopper for left 45° bevel angle)

8mm Bolt (A) (Stopper for 0°)

Fig. 8-a

Fig. 8-b

2.Securing the workpiece

WARNING: Always clamp or vise to secure the workpiece to the fence; otherwise the workpiece

might be thrust from the table and cause bodily harm.

3. Installing the holders ... (Optional accessory)

6mm Wing Bolt (Optional accessory)

Steel Holder Square (Optional

accessory)

6mm Wing

 

 

Nut (Optional

Height Adjustment

Base Surface

accessory)

Bolt 6mm (Optional

 

 

 

accessory)

 

The holders help keep longer workpieces stable and in place during the cutting operation.

(1)As indicated in Fig. 9, use a steel square for aligning the upper edge of the holders with the base surface.

Loosen the 6mm wing nut. Turn a height adjustment bolt 6mm, and adjust the height of the holder.

(2)After adjustment, firmly tighten the wing nut and fasten the holder with the 6mm wing bolt (optional accessory). If the length of Height Adjustment Bolt 6mm is insufficient, spread a thin plate beneath. Make sure the end of Height Adjustment Bolt 6mm does not protrude from the holder.

Fig. 9

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Avertissement AdvertenciaContents Important Safety Information Meanings of Signal WordsImportant Safety Instructions for Using ALL Power Tools Specific Safety Rules for Use of this Power Tool DON’Ts Replacement Parts USE Proper Extension Cord Double Insulation for Safer OperationOperation and Maintenance Name of PartsSpecifications C10FCHInstallation ApplicationsPreparation Before Operation Before Using Installing the dust bag, holder, stopper and visesMake sure the power source is appropriate for the tool Releasing the locking pinBefore Cutting Confirmation for use of sub fence …Optional accessory Position adjustment of laser line Only Model C10FCHSwitch Laser Line Switch operation Practical ApplicationsUsing the Vise Assembly Standard accessory Cutting OperationMiter cutting procedures Bevel cutting proceduresCompound cutting procedures Crown molding cutting procedures For miter cut settingFor bevel cut setting Crown molding Stopper L and R optional accessories allow How to use the dust bag Standard accessory SAW Blade Mounting and DismountingCutting easily-deformed materials, such as aluminum sash Mounting the saw blade -a, -b, -c and -dMaintenance and Inspection Dismounting the saw bladeInspecting the saw blade Inspecting the lever Inspecting the carbon brushes and FigAbout Handling the Motor see Fig Inspecting the screwsService and Repairs CleaningLubrication Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTConsignes DE Securite Relatives AUX Outils Électriques Français Consignes de sécurité spéciales pour cet outil électrique Français Pieces DE Rechange Utiliser LE Cordon DE Rallonge AppropriéDouble Isolation Pour UN Fonctionnement Plus SUR Français Utilisation ET Entretien NOM DES PiècesSpécifications Préparation Avant L’UTILISATION Avant L’UTILISATION Libérer la goupille de verrouillage’assurer que la source d’alimentation convient pour l’outil Vérifier que la gâchette est sur OFFAvant LA Coupe Une coupe stable du matériau avec une face arrière large Remarques Applications Pratiques Fonctionnement de l’interrupteurUtilisation de l’ensemble d’étau Accessoire standard CoupeProcédure de coupe d’onglet Procédure de coupe de biseauProcédures de coupe mixte Procédures de coupe de corniche complexe Réglage d’une coupe d’ongletRéglage d’une coupe de biseau ’étau B de corniche complexe accessoire en option peut Installation ET Retrait DE LA Lame Utilisation du sac à copeaux Accessoire standardInstallation de la lame -a, -b, -c et -d Retrait de la lameEntretien ET Inspection Service APRÈS-VENTE ET Réparations RemisageGraissage NettoyageInformación Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónNormas DE Seguridad Para LAS Herramientas Eléctricas Español Español Español Piezas DE Reemplazo Utilice EL Cable Prolongador Adecuado Aislamiento Doble Para Ofrecer UNA Operación MÁS SeguraOperación Y Mantenimiento Nomenclatura DE PartesEspecificaciones Mesa giratoria Dimensión máxima de corte Máxima IngletesAplicaciones Preparativos Previos a LA OperaciónInstalación Antes DE LA Utilización Liberación del pasador de bloqueoCerciórese de que el interruptor de disparo esté en OFF Compruebe si la hoja de sierra posee defectos visiblesAntes DEL Corte Posición de ajuste de la línea de láser Sólo modelo C10FCH Mm, como se muestra en la FigContinuación introduzca una llave de barra hexagonal de Aplicaciones Prácticas Operación de conmutaciónOperación de corte Procedimiento de corte de ingletes Procedimientos de corte de ingletesProcedimientos de corte compuesto Procedimientos de corte con moldura en vértice Para el ajuste de corte de ingletesPara el ajuste del corte en bisel Se muestra en la -a. Después de la in sercion, apriete el Forma de utilizar la bolsa para el polvo Accesorio estándar Una posición en que no haga contacto con la hoja de sierraMontaje Y Desmontaje DE LA Hoja DE Sierra Montaje de la hoja de sierra -a, -b, -c y -dMantenimiento E Inspección Desmontaje de la hoja de sierraInspección de la hoja de sierra Inspección de la palancaServicio Y Reparaciones Page Page Page Page Page Page Page Page Hitachi Koki Canada Co

C 10FCE specifications

The Hitachi C 10FCE is a powerful and versatile 10-inch sliding compound miter saw designed to meet the needs of both professional contractors and serious DIY enthusiasts. Renowned for its precision and ease of use, this tool is engineered to deliver accurate cuts while offering a range of features that enhance its functionality.

One of the standout features of the C 10FCE is its 15-amp motor, which delivers a robust performance capable of cutting through a variety of materials, including hardwoods, softwoods, and engineered woods. The motor provides a no-load speed of 5,000 RPM, allowing for swift and efficient cutting tasks. The saw is equipped with a unique 0 to 52-degree miter angle range, providing versatility for making precise crosscuts at various angles. The dual-bevel functionality allows users to make beveled cuts in both directions, amplifying the tool’s adaptability for a wide range of projects.

The C 10FCE is also equipped with a laser guide system, which aids in ensuring accuracy by projecting a line on the workpiece where the cut will occur. This feature is particularly useful for achieving clean and precise cuts, reducing the likelihood of errors. Additionally, the saw boasts a large, robust table that provides ample support for larger workpieces, enhancing stability during use.

Durability is an important characteristic of the Hitachi C 10FCE. The saw features a rigid base that minimizes vibration and maximizes stability, resulting in smoother operation. The model is constructed with high-quality materials, ensuring longevity and consistent performance over time.

Safety is another key aspect integrated into the C 10FCE design. The saw includes a blade guard that covers the upper portion of the blade while in operation, protecting users from accidental contact. The electric brake system stops the blade quickly after the trigger is released, further enhancing user safety.

In conclusion, the Hitachi C 10FCE sliding compound miter saw is a feature-rich tool combining power, precision, and safety. With its reliable motor, versatile cutting angles, laser guide system, and durable construction, it stands as an ideal choice for anyone looking to tackle complex cutting tasks with confidence and accuracy. Whether for intricate trim work or larger construction projects, the C 10FCE is built to handle a diverse range of applications efficiently.
Top Page Image Contents