Hitachi C 10FCE Maintenance and Inspection, Dismounting the saw blade, Inspecting the saw blade

Page 21

English

(4) Remove the bolt and washer (D)

Spindle Lock

4mm Machine Screw

Spindle Cover

Fig. 33-a

Fig. 33-b

(5) Lift the lower guard and mount the saw blade.

WARNING: When mounting the saw blade, confirm that the rotation indicator mark on the saw blade and the rotation direction of the gear case (see Fig. 1) are properly matched.

(6) Thoroughly clean washer (D) and the bolt, and install them onto the saw blade spindle.

6mm Bolt

Saw Blade

(15.9mm)

10mm Box Wrench

Washer

Bolt

Washer (D)

5/8"

 

Washer (D) (Chamfering side)

Washer (D)

Fig. 33-c

Fig. 33-d

 

(7)Press in the spindle lock and tighten the bolt by turning it to the left by standard accessorie’s wrench (10mm box wrench) as indicated in Fig. 33-c.

CAUTION: * Confirm that the spindle lock has returned to the retract position after installing or removing the saw blade.

*Tighten the bolt so it does not come loose during operation.

Confirm the bolt has been properly tightened before the power tool is started.

2.Dismounting the saw blade

Dismount the saw blade by reversing the mounting procedures described in paragraph 1 above. The saw blade can easily be removed after lifting the safety cover.

CAUTION: Never attempt to install saw blades larger than 10" (255mm) in diameter. Always install saw blades that are 10" (255mm) in diameter or less.

MAINTENANCE AND INSPECTION

WARNING: To avoid an accident or personal injury, always confirm that the trigger switch is turned OFF and the power plug has been disconnected from the receptacle before performing any maintenance or inspection of this tool.

1. Inspecting the saw blade

Always replace the saw blade immediately upon the first sign of deterioration or damage.

A damaged saw blade can cause personal injury and a worn saw blade can cause ineffective operation and possible overload to the motor.

CAUTION: Never use a dull saw blade. When a saw blade is dull, its resistance to the hand pressure applied by the tool handle tends to increase, making it unsafe to operate the power tool.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Advertencia AvertissementContents Important Safety Information Meanings of Signal WordsImportant Safety Instructions for Using ALL Power Tools Specific Safety Rules for Use of this Power Tool DON’Ts Replacement Parts Double Insulation for Safer Operation USE Proper Extension CordName of Parts Operation and MaintenanceC10FCH SpecificationsInstallation ApplicationsPreparation Before Operation Installing the dust bag, holder, stopper and vises Before UsingMake sure the power source is appropriate for the tool Releasing the locking pinBefore Cutting Position adjustment of laser line Only Model C10FCH Confirmation for use of sub fence …Optional accessorySwitch Laser Line Practical Applications Switch operationCutting Operation Using the Vise Assembly Standard accessoryMiter cutting procedures Bevel cutting proceduresCompound cutting procedures Crown molding cutting procedures For miter cut settingFor bevel cut setting Crown molding Stopper L and R optional accessories allow SAW Blade Mounting and Dismounting How to use the dust bag Standard accessoryCutting easily-deformed materials, such as aluminum sash Mounting the saw blade -a, -b, -c and -dMaintenance and Inspection Dismounting the saw bladeInspecting the saw blade Inspecting the carbon brushes and Fig Inspecting the leverAbout Handling the Motor see Fig Inspecting the screwsService and Repairs CleaningLubrication Informations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTConsignes DE Securite Relatives AUX Outils Électriques Français Consignes de sécurité spéciales pour cet outil électrique Français Pieces DE Rechange Utiliser LE Cordon DE Rallonge AppropriéDouble Isolation Pour UN Fonctionnement Plus SUR Français NOM DES Pièces Utilisation ET EntretienSpécifications Préparation Avant L’UTILISATION Libérer la goupille de verrouillage Avant L’UTILISATION’assurer que la source d’alimentation convient pour l’outil Vérifier que la gâchette est sur OFFAvant LA Coupe Une coupe stable du matériau avec une face arrière large Remarques Fonctionnement de l’interrupteur Applications PratiquesCoupe Utilisation de l’ensemble d’étau Accessoire standardProcédure de coupe d’onglet Procédure de coupe de biseauProcédures de coupe mixte Procédures de coupe de corniche complexe Réglage d’une coupe d’ongletRéglage d’une coupe de biseau ’étau B de corniche complexe accessoire en option peut Utilisation du sac à copeaux Accessoire standard Installation ET Retrait DE LA LameRetrait de la lame Installation de la lame -a, -b, -c et -dEntretien ET Inspection Remisage Service APRÈS-VENTE ET RéparationsGraissage NettoyageInformación Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónNormas DE Seguridad Para LAS Herramientas Eléctricas Español Español Español Piezas DE Reemplazo Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Utilice EL Cable Prolongador AdecuadoNomenclatura DE Partes Operación Y MantenimientoMesa giratoria Dimensión máxima de corte Máxima Ingletes EspecificacionesAplicaciones Preparativos Previos a LA OperaciónInstalación Liberación del pasador de bloqueo Antes DE LA UtilizaciónCerciórese de que el interruptor de disparo esté en OFF Compruebe si la hoja de sierra posee defectos visiblesAntes DEL Corte Mm, como se muestra en la Fig Posición de ajuste de la línea de láser Sólo modelo C10FCHContinuación introduzca una llave de barra hexagonal de Operación de conmutación Aplicaciones PrácticasOperación de corte Procedimiento de corte de ingletes Procedimientos de corte de ingletesProcedimientos de corte compuesto Procedimientos de corte con moldura en vértice Para el ajuste de corte de ingletesPara el ajuste del corte en bisel Se muestra en la -a. Después de la in sercion, apriete el Una posición en que no haga contacto con la hoja de sierra Forma de utilizar la bolsa para el polvo Accesorio estándarMontaje de la hoja de sierra -a, -b, -c y -d Montaje Y Desmontaje DE LA Hoja DE SierraDesmontaje de la hoja de sierra Mantenimiento E InspecciónInspección de la hoja de sierra Inspección de la palancaServicio Y Reparaciones Page Page Page Page Page Page Page Page Hitachi Koki Canada Co

C 10FCE specifications

The Hitachi C 10FCE is a powerful and versatile 10-inch sliding compound miter saw designed to meet the needs of both professional contractors and serious DIY enthusiasts. Renowned for its precision and ease of use, this tool is engineered to deliver accurate cuts while offering a range of features that enhance its functionality.

One of the standout features of the C 10FCE is its 15-amp motor, which delivers a robust performance capable of cutting through a variety of materials, including hardwoods, softwoods, and engineered woods. The motor provides a no-load speed of 5,000 RPM, allowing for swift and efficient cutting tasks. The saw is equipped with a unique 0 to 52-degree miter angle range, providing versatility for making precise crosscuts at various angles. The dual-bevel functionality allows users to make beveled cuts in both directions, amplifying the tool’s adaptability for a wide range of projects.

The C 10FCE is also equipped with a laser guide system, which aids in ensuring accuracy by projecting a line on the workpiece where the cut will occur. This feature is particularly useful for achieving clean and precise cuts, reducing the likelihood of errors. Additionally, the saw boasts a large, robust table that provides ample support for larger workpieces, enhancing stability during use.

Durability is an important characteristic of the Hitachi C 10FCE. The saw features a rigid base that minimizes vibration and maximizes stability, resulting in smoother operation. The model is constructed with high-quality materials, ensuring longevity and consistent performance over time.

Safety is another key aspect integrated into the C 10FCE design. The saw includes a blade guard that covers the upper portion of the blade while in operation, protecting users from accidental contact. The electric brake system stops the blade quickly after the trigger is released, further enhancing user safety.

In conclusion, the Hitachi C 10FCE sliding compound miter saw is a feature-rich tool combining power, precision, and safety. With its reliable motor, versatile cutting angles, laser guide system, and durable construction, it stands as an ideal choice for anyone looking to tackle complex cutting tasks with confidence and accuracy. Whether for intricate trim work or larger construction projects, the C 10FCE is built to handle a diverse range of applications efficiently.
Top Page Image Contents