Grizzly G0646, G0647 owner manual Inventory Clean Up, Inventory Figure Qty

Page 17

Inventory

 

Clean Up

 

 

 

 

 

 

The following is a description of the main compo- nents shipped with your machine. Lay the compo- nents out to inventory them.

Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging materials carefully. Occasionally we pre-install certain components for shipping purposes.

Inventory: (Figure 8)

Qty

A.

Ironworker (not shown)

1

B.

Guide Bar Assembly

1

C.

Extension Bar Assembly

1

D.

Toolbox

1

E.

Cap Screws M10-1.5 x 50 (Guide Bar)

3

F.

Lock Washers (Guide Bar)

3

G.

Punch Adapter 9036

1

H.

Punch Adapter 81031

1

I.

Punch Adapter 81029

1

J.

Spanner Wrench

1

K.

Adjustable Wrench

1

L.

Grease Gun

1

M.

Hex Wrench 17mm

1

N.

Hex Wrench 14mm

1

O.

Hex Wrench 12mm

1

P.

Hex Wrench Set 2.5–10mm

1

The unpainted surfaces are coated with a waxy oil to prevent corrosion during shipment. Remove this protective coating with a solvent cleaner or degreaser, such as shown in Figure 9. For thor- ough cleaning, some parts must be removed.

For optimum performance, clean all moving parts or sliding contact surfaces. Avoid chlo- rine-based solvents, such as acetone or brake parts cleaner that may damage painted surfac- es. Always follow the manufacturer’s instructions when using any type of cleaning product.

Gasoline and petroleum products have low flash points and can explode or cause fire if used to clean machinery. DO NOT use these products to clean the machinery.

Many cleaning solvents are toxic if inhaled. Minimize your risk by only using these products in a

G

B

D

F E

I

H

C

J

K

P

L

M

N

O

well ventilated area.

G2544—Solvent Cleaner & Degreaser

A great product for removing the waxy shipping grease from your machine during clean up.

Figure 8. Model G0646/G0647 inventory.

If any nonproprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store.

G0646/G0647 50/65 Ton Ironworker

Figure 9. Cleaner/degreaser available from

Grizzly.

-15-

Image 17
Contents 50/65 TON Ironworker Page Table of Contents Contact Info IntroductionForeword Functional Overview Identification G0646 Machine Data Sheet G0646/G0647 50/65 Ton Ironworker G0647 Machine Data Sheet G0646/G0647 50/65 Ton Ironworker Safety Instructions for Machinery G0646/G0647 50/65 Ton Ironworker Additional Safety Instructions for Ironworkers Additional Safety Instructions for Hydraulics Power Connection Device Power Supply Circuit RequirementsCircuit Requirements 220/440V Operation440V Conversion To rewire the Model G0646/G0647 for 440V operationSetup Safety SetupItems Needed for Setup UnpackingInventory Figure Qty Inventory Clean UpSite Considerations Placement LocationMoving & Placing Base Unit Floor LoadBolting to Concrete Floors Using Machine MountsMounting to Shop Floor To test run the machine Test RunFactory adjustments that should be verified Recommended AdjustmentsBasic Controls Operation SafetyOperations Operation Tips Using the Punching StationPunching Motor Stop Button Turns the motor OFFTo remove punch tooling Removing/Installing Punch ToolingTools Needed Qty Punch, adapter, retaining ring, Die installed To install punch toolingBolster Mounting Hex Bolts 4 shown Notching Using the Notching StationRemoving & Installing Notch Dies Notch Die Clearances To install the notch diesPage To avoid tooling or workpiece breakage Flat Stock ShearingTo shear flat stock To shear bar stock Bar Stock ShearingMaking a 90 Cut Extension BarAngle Iron Shearing Making a Less Than 90 Cut Adjusting Stroke Length Beam Lubrication T20448T20452 T20501 T20456 H0736 AccessoriesH7379-Tapmatic#1 Gold 16 oz H7380-Tapmatic#1 Gold 1 Gal Available Tooling Schedule MaintenanceCleaning Protecting Beam Pivot Shaft Shearing Hold-Down Adjustment RodLubrication Support Frame Lubrication Fluid Capacity Hydraulic SystemFilling Hydraulic Reservoir To drain and re-fill the hydraulic reservoir Draining & Re-Filling HydraulicReservoir To align the beam Beam AlignmentMotor & Electrical ServiceTroubleshooting Operations To remove and replace the flat stock shearing dies Flat Stock Shearing DiesTo remove the angle iron shearing dies Angle Iron Shearing DiesTo remove and replace the bar stock shearing dies Bar Stock Shearing DiesDisconnect Machine from Power Shearing Table Alignment Hydraulic Fluid Pressure To reset the position of the limit ringsLimit Rings Electrical Panel Wiring Control Panel Wiring Electrical Panel Wiring Diagram Control Panel Wiring Diagram Limit switch wiring Electrical Components Wiring DiagramMotor wiring G0646/G0647 50/65 Ton Ironworker Motor Wiring DiagramHydraulic System Overview Parts Description G0646 Upper Front-Half Parts ListG0647 Upper Front-Half Parts List Half UpperG0646 Upper Rear-Half Parts List Description G0647 Upper Rear-Half Parts ListCabinet G0646 Cabinet G0647 Cabinet Notching Station Punching Station Extension Bar & Tools Label Placement Page Page Warranty and Returns